TechNexion TWP-1010-IMX6 User manual

3.1 VESA Mounng
3.2 Yoke Mounng
TWP-1010-IMX6 / TWP-1560-IMX6
Quickstart Guide
3 Installaon Instrucons
This secon describes the mounng procedures for the TWP series device. The material in the mounng area must
provide sufficient strength for support of this HMI.
This device is compable with VESA MIS-D Standard 75*75mm. There are 4 VESA MIS-D (M4) mounng holes on
the rear side of the device. M4 screws with at least 6mm head-to-p length are required to secure this device.
This device is compable with 50mm Yoke Standard. There are two Yoke (M6) mounng holes each on the le and
on the right side of the device. M6 screws with at least 7.5mm head-to-p length are required to secure this
device.
INNOVATORS OF TECHNOLOGY
2 Dimensions
TWP-1010-IMX6 TWP-1560-IMX6
TWP-1010-IMX6 TWP-1560-IMX6
1 Safety Precauons
Thank you for purchasing a TechNexion TWP series device. This installaon guide will be helpful in the installaon,
wiring and inspecon of your TechNexion stainless steel IP69K HMI. Before using the product, please read this
guide to ensure correct use. You should thoroughly understand all safety precauons before proceeding with the
installaon, wiring, and operaon. Place this instrucon sheet in a safe locaon for future reference.
• Keep the device dry. Precipitaon, humidity, and all types of liquids or moisture can contain minerals that will
corrode electronic circuits. If your device does get wet, allow it to dry completely.
• Do not use or store the device in dusty or dirty areas. Its parts and electronic components can be damaged.
• Do not store the device in hot areas. High temperatures can shorten the life of electronic devices, damage
baeries, and warp or melt certain plascs.
• Do not store the device in cold areas. When the device returns to its normal temperature, moisture can form
inside the device and damage electronic circuit boards.
• Do not aempt to open the device.This product needs to be installed by qualified personnel.
• Do not drop, knock, or shake the device. Rough handling can break internal circuit boards and fine mechanics.
• Do not paint the device. Paint can clog the parts and prevent proper operaon.
• Unauthorized modificaons or aachments could damage the device and may violate regulaons governing radio
devices.
• Do not touch any internal or exposed parts of the device as electrical shock may result.
• Do not open the device while power is on. Otherwise electrical shock may result.
• Do not use harsh chemicals, cleaning solvents, or strong detergents to clean the device.
• Be sure the venlaon holes are not obstructed during operaon. Otherwise malfuncon may result due to
bad venlaon or overheang.
These suggesons apply equally to your device, baery, charger, or any enhancement. If any device is not
working properly, take it to the nearest authorized service facility for service.
• Make sure that the available power source matches the required input power of the device. Failure to observe
this cauon may result in electric shock or fire.
• Do not power the unit by DC input when you apply power over the PoE (8-pin M12).
1.1 Storage and Installaon
1.2 Wiring
1.3 Maintenance and Inspecon
!
Unit : mm
211.8
57.5 293.2
289.1
438.4
56.5
75
75
4-M4
75
75
4-M4
1 2

4 External Connectors
Le side view: Right side view:
Rear view: Rear view:
Le side view: Right side view:
• All Rights Reserved. No part of this document may be photocopied, reproduced, stored in a retrieval system, or transmied, in any
form or by any means whether, electronic, mechanical, or otherwise without the prior wrien permission of TechNexion Ltd.
• No warranty of accuracy is given concerning the contents of the informaon contained in this publicaon. To the extent permied
by law no liability (including liability to any person by reason of negligence) will be accepted by TechNexion Ltd., its subsidiaries or
employees for any direct or indirect loss or damage caused by omissions from or inaccuracies in this document.
• TechNexion Ltd. reserves the right to change details in this publicaon without noce. Please download the most updated version
at: hps://www.technexion.com/support/download-center/
TWP-1010-IMX6 TWP-1560-IMX6
TWP-1010-IMX6 TWP-1560-IMX6
Description No.No. Description
1 Antenna hole
Grounding M4 screw
DC Input(3-pin M12) connector
LAN (8-pin M12) connector
USB 2 port (8-pin M12) connector
RS-XXX Serial Port (8-pin M12) connector
OPT-A connector hole
OPT-B connector hole
OPT-C connector hole
Antenna hole
2
3
4
5
6
7
8
9
10
Phone: [phone]
Web: www.technexion.com
16F-5, No. 736, Zhongzheng Road,
ZhongHe District, 23511, New Taipei City, Taiwan
© 2001-2018 TechNexion Ltd.
2018-11-09
5.1 Power Input Connector (DC INPUT)
5 Pin Definion
The TWP-1010-IMX6/TWP-1560-IMX6 can be powered either over the DC INPUT connector or PoE
(oponal) over the M12 LAN port.
Header: Amphenol LTW 12-03PMMP-SF8003 (3-pin M12) front fastened male connector.
Cable receptacle: Amphenol LTW 12-03BFFA-SL8001 (3-pin M12) screw thread female connector.
NOTE: Do not power the unit by DC input when you apply power over the Power over Ethernet (M12)!
Port Pin # Signal Device
1 GND Ground
DC Voltage input (12V/24V/8~36VDC)3 VCC
4 NC
5.2 Gigabit Ethernet Interface (LAN)
Header: Amphenol LTW 12-08PMMP-SF8003 (8-pin M12) front fastened male connector.
Cable receptacle: Amphenol LTW 12-08BFFA-SL8001 (8-pin M12) screw thread female connector.
MDI0+
MDI0-
MDI1+
MDI2+
MDI2-
MDI1-
MDI3+
MDI3-
Transmit Data+
Transmit Data-
Receive Data+
Receive Data-
Transmit Data+
Transmit Data-
Receive Data+
Receive Data-
Port Pin # 1000 Mbps 100 Mbps 10 Mbps
1
2
3
4
5
7
6
8
5.3 USB Connector (USB)
5.4 Serial Port Connector (RS-XXX)
Header: Amphenol LTW 12-08PMMP-SF8003 (8-pin M12) front fastened male connector.
Cable receptacle: Amphenol LTW 12-08BFFA-SL8001 (8-pin M12) screw thread female connector.
Header: Amphenol LTW 12-08PMMP-SF8003 (8-pin M12) front fastened male connector.
Cable receptacle: Amphenol LTW 12-08BFFA-SL8001 (8-pin M12) screw thread female connector.
Port Pin # GPIO1/2 Signal Description
1 VBUS
VBUS
USB_D-
USB_D+
USB_D-
USB_D+
GND
GND
5V Universal Serial Bus Power port 1
5V Universal Serial Bus Power port 2
Ground port 1
Ground port 2
2
3
4
5
6
7
8
The unit is preloaded with soware that can download and install a selecon of OS images over hardwired
network. Simply connect a network to the unit through the Ethernet LAN M12 connector and power it up, then
follow the steps on the screen to load the soware. Local proxies will interfere with this process. For more
informaon, go to our Knowledge Base at: hps://www.technexion.com/support/knowledge-base/
6 Soware Installaon
50
25
4-M6
4-M6
50
25
2 3 4 567 18 9
10
1 2 3 4 567 8 9
10
1
4 3
1 2
8
7
6 5
3
4
1 2
8
7
6 5
3
4
Port Pin # GPIO1/2 Signal Device
1 NC
SERIAL1A_RXD
SERIAL1A_TXD
NC
GND
NC
SERIAL1A_RTS
SERIAL1A_CTS
2
3
4
5
6
7
8
1 2
8
7
6 5
3
4
ttymxc0
ttymxc0
ttymxc0
ttymxc0
Universal Serial Bus differential pair signal port 1
Universal Serial Bus differential pair signal port 2
3 4