Technika STB 9005 User manual

Digital Terrestrial Receiver
STB 9005
Operating Instructions
Technika STB 905.book Seite 1 Mittwoch, 27. September 2006 8:21 08

Tabel of Contents
2
1. Control elements and functional components . . . . . . . . . 3
2. Your DVB-T receiver introduces itself . . . . . . . . . . . . . . . . 6
3. Scope of delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
4. Safety warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
5. Connecting the receiver . . . . . . . . . . . . . . . . . . . . . . . . . . 11
6. Commissioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
7. Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Changing channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Volume control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Info banner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Showing the help text . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Using the channel list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Blocking a channel (Parental lock) . . . . . . . . . . . . . . . . . . . . . . . 19
Adding a channel to your favourites . . . . . . . . . . . . . . . . . . . . . . 20
Extended installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
EPG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Selecting the language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Use text/MHEG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Listening to the radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Software Upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Parental Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
8. Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
9. Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Technika STB 905.book Seite 2 Mittwoch, 27. September 2006 8:21 08

Operation
3
1. Control elements and functional components
Front view of the receiver
A IR sensor with LED display
Green: device is switched on
Red: device in standby mode
No colour: device is not connected to the mains supply
Rear view of the receiver
BRF IN socket for antenna connection
C Analogue audio left L
D VCR/DVD SCART connection VCR
E Mains connection socket 12 V
F TV-SCART connection TV
G Analogue audio right R
HRF OUT socket for antenna output
(Loop-through socket)
A
BCD
G
HFE
Technika STB 905.book Seite 3 Mittwoch, 27. September 2006 8:21 08

STB 9005
4
Remote control
1On / Off
2Mute
mute the sound, pressing again switches the sound back
on
3TV/radio button
open the channel list
1
2
3
25
15
23
14
24
4-13
16
22
21
27
26
28
29
30-33
17-20
Technika STB 905.book Seite 4 Mittwoch, 27. September 2006 8:21 08

Operation
5
4-13 Numerical keys
- direct channel selection via the individual buttons
- edit timer settings
14, 21 Channel buttons Ch+ / Ch-
select next / previous channel
15, 22 Volume buttons Vol+ / Vol-
increase / decrease volume
16 OK button
- confirm selection
- open the channel list
17-20 Arrow buttons
- for navigation
- selection in menus
23 Info button
- show information banner
- show help in the menu
24 Exit button
- cancel procedure
-exitmenu
25 Text button
open the MHEG (info guide)
26 EPG button
open the EPG
27 Swap button
change between the two channels last viewed
28 Menu button
open the main menu
29 OPT button
opens the configuration window
30-33 Colour buttons
EPG operation / MHEG
Technika STB 905.book Seite 5 Mittwoch, 27. September 2006 8:21 08

STB 9005
6
2. Your DVB-T receiver introduces itself
Welcome!
With your new digital receiver the whole world of digital
television is open to you - and in top quality!
These Operating Instructions help you to optimally use the
extensive functions and options of your new digital receiver.
Overview of the features
DVB terrestrial TV and Radio reception
Logical Channel Numbering (LCN) support
MHEG5 support
Easy-to-use graphical user interface
Automatic and manual channel scan
Electronic Program Guide (EPG)
Aspect ratio: 4:3, 16:9
Wide Screen Signalling (WSS) for AFD support
Context based help function
3. Scope of delivery
After unpacking the device, check the contents below are all
present and undamaged:
1 receiver
1 Operating Instructions (including Quick Start Guide)
1 remote control (battery already inserted)
1 SCART cable
1 pluggable power supply (AC/DC Adaptor)
Technika STB 905.book Seite 6 Mittwoch, 27. September 2006 8:21 08

Operation
7
4. Safety warnings
Basic notes
  Intended use
This device serves to receive digital channels via an antenna.
The replay is effected via a TV connected to the receiver.
Every other use is not intended and is impermissible.
Only the functions described in these Operating Instructions
may be carried out with this device.
The receiver is designed for domestic use.
  Notes regarding the Operating Instructions
If possible, keep the Operating Instructions ready at hand
near the appliance.
If you hand the receiver on to another person, please also
enclose these Operating Instructions.
Danger to children
Never leave children unattended with this device. Children
underestimate the danger associated with electric
appliances.
Keep children away from the packing material. When it is
swallowed, there is a risk of suffocation.
Batteries can be dangerous if they are swallowed. Therefore
keep batteries out of reach of babies. If a battery has been
swallowed, seek medical assistance immediately.
Technika STB 905.book Seite 7 Mittwoch, 27. September 2006 8:21 08

STB 9005
8
Danger caused by electricity
In the interior of the device there are hazardous voltages.
Never open the housing or insert objects through the
ventilation openings.
The device must not be exposed to dripping or splashing
water. Prevent liquids from entering into the device. If this
happens, immediately disconnect the power plug.
Do not place items filled with fluids, like vases or coffee mugs
on the device.
The device must not be used in damp locations (e. g.
bathroom) or rooms with heavy dust accumulation.
Only connect the pluggable power supply of the device to a
power outlet that is installed according to regulations.
The power outlet has to be easily accessible so that you are
able to disconnect the power plug immediately if necessary.
Check that the connector cables are not pinched or
squeezed.
Do not switch on the device if the device or the connector
cables show visible damage, or if the device has been
damaged.
If apparent damage occurs (e. g. smoke or similar) during
operation, immediately disconnect the power supply from the
power outlet. In doing this, always pull at the plug, never at
the cable.
Power outlets and extension cables must not be overloaded,
as this may create fire hazard!
In order to completely disconnect the device from the power
supply, the power supply has to be disconnected from the
power outlet.
Do not make any modifications to this device.
Technika STB 905.book Seite 8 Mittwoch, 27. September 2006 8:21 08

Operation
9
Have repairs to on your receiver carried out by qualified
skilled personnel only. The manufacturer accepts no liability
for accidents to the user if the device is opened. Incorrect
wiring of the connections can result in failures or malfunctions
on the device.
Use the provided cables and pluggable power supplies only.
During thunderstorms devices may be damaged by power
surges. Therefore, in the event of a thunderstorm always
disconnect the pluggable power supply from the power outlet
and remove the antenna connector.
If you do not use the receiver for a long period of time,
disconnect it from the power supply and antenna connection.
This also applies to devices connected to the receiver.
Danger of injuries by other causes
Check that nobody can trip over the connector cables.
Notes with regard to the installation location
Always place the device on a solid, even surface.
Do not expose this device to extreme temperatures.
Therefore:
- avoid direct sunlight and radiator heat,
- leave a minimum space of approx. 50 cm above and to the
sides,
- do not cover the device with magazines, table cloths or
similar. The heat may not build up in the device an create
a fire hazard!
The device must not be installed close to inflammable
material (e. g. curtains, flammable liquids, etc.).
Handling of batteries
Batteries must not be thrown into the fire, disassembled, or
short-circuited.
Replace the batteries at least one a year to prevent them
from leaking. If you do not use the device for a long period of
time, remove the batteries from the remote control.
Technika STB 905.book Seite 9 Mittwoch, 27. September 2006 8:21 08

STB 9005
10
Never try to reactivate a used battery by heat, charging, or by
other means.
Miscellaneous notes
Only switch the receiver on after the connections with the
antenna and the TV set have been established.
Do not place open fire sources, for example burning candles,
on the device.
Opening the device results in loss of warranty.
Condensation can be produced within the device, e. g. if the
device is brought in from a cold to a warm environment. In
such cases wait for approx. one hour before commissioning
the receiver. After this amount of time, the condensation has
usually evaporated.
Disposal of battery and device
Contact your local authority to establish the correct method of
disposal for both the device at end of life and spent batteries.
Technika STB 905.book Seite 10 Mittwoch, 27. September 2006 8:21 08

Operation
11
5. Connecting the receiver
Inserting the battery into the remote control
The battery (type CR2025 / 3 V) is already inserted in the
remote control. It is covered by an insulating plastic separator to
avoid premature discharge of the battery.
1. To remove the battery, extract it from the remote control as
showed above.
2. Simply re-insert the battery compartment into the remote
control.
The remote control is now ready for use.
Connecting the receiver
    Note:
Observe the connection diagram, see page 13.
  Connection to an antenna
Connect the antenna via a (not supplied) coaxial cable to the
receiver. First connect the coaxial cable to the antenna and
then to the RF IN socket of the receiver.
Caution!
Please be sure that all devices are switched off before you
connect them. Only plug in the power supply when all other
connections have been established. By this, possible damage
is avoided.
Technika STB 905.book Seite 11 Mittwoch, 27. September 2006 8:21 08

STB 9005
12
  Connection to a Television
Connect the receiver and TV set by means of the SCART cable.
Connect the TV SCART socket and the corresponding
SCART socket of your TV set using a SCART cable.
    Note:
If your TV set is provided with more than one SCART sockets,
consult the Operating Instructions of the TV set. This will advise
you which SCART socket is appropriate for the connection.
    NOTE:
If you also want to receive analog channels in addition to the
digital channels, the analog signal of these channels has to be
"looped through“. For this purpose, connect the RF OUT socket
of the receiver to the antenna input socket of your TV set by
means of an additional coaxial cable.
  Connection of a video or DVD recorder
Connect the receiver and video/DVD recorder to each other
using a further SCART cable.
Connect the VCR SCART socket and the corresponding
SCART socket of the other device using a SCART cable.
    NOTE:
If your recorder is provided with more than one SCART socket,
consult the Operating Instructions of the device.
Caution!
Do not use the decoder input included on some TV sets. For
this, read the Operating Instructions of your TV set.
Technika STB 905.book Seite 12 Mittwoch, 27. September 2006 8:21 08

Operation
13
Connection diagram
  Connection to a stereo
Connect the AUDIO OUT L and Routput sockets to the
corresponding input sockets of your stereo using a cinch
cable (not included).
    NOTE:
Observe the Operating Instructions of your stereo or audio
system.
Antenna
Mains Adaptor
VCR
TV
Stereo
Technika STB 905.book Seite 13 Mittwoch, 27. September 2006 8:21 08

STB 9005
14
  Connecting the power cable
Connect the device and the power outlet using the power
supply.
1. First connect the power cable to the power connection of the
receiver.
2. Then plug the power supply into a power outlet.
6. Commissioning
Switching on the receiver
Switch on the receiver by pressing the Power button on the
remote control.
When you switch on your receiver for the first time, the “First
Time Installation“ assistant will guide you through all the
required steps.
The selection is carried out by the Arrow buttons orand
the OK button.
    NOTE:
You may have to set the AV channel on your TV set. Information
on this can be found in the Operating Instructions of your TV set.
First time installation
After the first switch-on, the following window appears:
Caution!
Only connect the device to a power outlet that is installed
according to regulations.
Only switch the device on after the connections with the
antenna and the SCART cable have been established.
Technika STB 905.book Seite 14 Mittwoch, 27. September 2006 8:21 08

Operation
15
1. Select the screen format of your TV using the Arrow buttons
orand press the OK button.
2. Press OK to start the automatic search.
    NOTE:
If you do not press the OK button, the search is started
automatically after a few seconds.
The screen dialogue provides information on the progress of the
channel search. Furthermore you will see the channels that
have been found listed as below.
As soon as the search is completed, the first channel found will
be displayed.
Technika STB 905.book Seite 15 Mittwoch, 27. September 2006 8:21 08

STB 9005
16
7. Operation
Changing channel
You can change the channel in different ways:
By pressing the Ch +or Ch buttons.
By pressing the Swap button you skip between the two
channels last viewed.
By selecting the channel directly via the channel list, see
page 18.
By entering the memory number in the channel list. For this
purpose, enter the number via the numerical buttons. For
instance, if the memory has the number 80, press the
corresponding numerical buttons successively.
Volume control
Use the Volume buttons Vol + and Vol - to increase or
decrease the volume.
The volume selected is shown in the form of a bar on the screen.
Mute function
By pressing the Mute button, the sound reproduction is
stopped.
The sound is audible again if you ...
... press the Mute button again, or
... press one of the volume control buttons.
Info banner
At every channel change the info banner is displayed.
Technika STB 905.book Seite 16 Mittwoch, 27. September 2006 8:21 08

Operation
17
1. Press the INFO button to call up the information banner without
changing the channel.
The info banner displays the following information:
storage space number, channel, mode and time,
signal strength,
the current programme and the following programme
including their broadcasting times.
2. Press the Info button i again to have information on the current
and next programme, respectively, displayed.
3. Where required, use the Arrow buttons =and=to have
further text displayed in the window.
    NOTE:
You can also press the yellow or blue colour button to have
information on the current or next programme displayed.
4. Close the window by pressing the Info button i or the Exit
button once.
Showing the help text
If a window is opened, you show a window with a help text and
hide it again by using the Info button i. It informs you on the
respective operation of the functions.
Technika STB 905.book Seite 17 Mittwoch, 27. September 2006 8:21 08

STB 9005
18
Using the channel list
  Selecting a channel
1. Press the TV/Radio button or the OK button to call the channel
list.
2. By means of the Arrow buttons you can navigate in the
channel list:
The current channel is displayed on the right while the
channel list is shown on the left.
Use the Arrow buttons =and=to select the desired
channel which is shown on the right.
3. After pressing OK you change to the desired channel.
4. Press Exit to close the channel list and view the selected
channel.
  Deleting / editing the channels
By pressing the Arrow button orand the OK button, you
can delete channels and change the channel name in the
channel list.
1. Open the channel list.
Technika STB 905.book Seite 18 Mittwoch, 27. September 2006 8:21 08

Operation
19
2. Use the Arrow buttons and the OK button to select the
desired function.
3. When you change a channel name, use the Numerical buttons
of the remote control to change the channel name.
The following table shows you how to generate or enter the
different characters:
Blocking a channel (Parental lock)
The block function prevents access to a channel.
    NOTE:
In order to be able to block channels, you must have carried out
the corresponding settings in the configuration window, see
page 29.
1. Open the channel list.
2. Highlight Lock and press the OK button.
3. Enter the code that consists of four digits via the buttons of the
remote control (standard code at delivery: 0000).
In the left half of the channel list a lock symbol is displayed next
to the channel name.
RemoteButton 1234567890
Press once 1 A D G J M P T W
Press twice . B E H K N Q U X 0
Press three times , C F I L O R V Y +
Pressfourtimes : 23456S8Z-
Press five times ; a d g j m 7 t 9 *
Presssixtimes ! behknpuw/
Press seven times ? c f i l o q v x $
Press eight times @ r y %
Press nine times / s z &
Technika STB 905.book Seite 19 Mittwoch, 27. September 2006 8:21 08

STB 9005
20
4. Press Exit to close the channel list.
Now the channel can only be selected after entering the four
digit lock code.
Adding a channel to your favourites
Favourites are usually channels that you frequently wish to
watch. If you have added channels to a favourite list, only
"favoured" channels are displayed when you change channels
using the Ch +or Ch buttons. There are a total of five favourite
lists available.
1. Open the channel list.
2. Select Favourites by means of the Arrow button orand
press the OK button.
The favourite list is displayed.
Technika STB 905.book Seite 20 Mittwoch, 27. September 2006 8:21 08