Strong SRT 6011 User manual

Picture similar
User Manual
Digital Free-To-Air Satellite
Receiver SRT 6011

Explanation of WARNING symbols
The lightning flash with arrowhead symbol within
an equilateral triangle is intended to alert the
user to the presence of not isolated dangerous
voltage within the inside of the product that may
be of sufficient magnitude to constitute a risk of
electric shock to persons.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and servicing
instructions in the literature accompanying
the appliance.
Read the following instructions carefully
WARNING: TO REDUCE THE RISK OF FIRE, ELECTRICAL
SHOCK OR ANNOYING INTERFRERENCE, DO NOT
EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE AND
ONLY USE THE RECOMMENDED ACCESSORIES.
n Read All Instructions — Before you use the product, read all
operating instructions. For more information on accessories
such as the lithium ion battery, refer to the manuals provided
with those products
n Save These Instructions — Save all safety and operating
instructions for future reference
n Heed Warnings — Read carefully and follow all warning labels
on the product and those described in the instructions.
n Follow Instructions — Follow all instructions provided with
this product
n Cleaning — Always unplug this product from the wall outlet
before cleaning. Use only a damp cloth for cleaning. Never
use any type of liquid or aerosol cleaner, or any type of organic
solvent to clean this product
n Attachments — For your safety, and to avoid damaging the
product, use only accessories recommended by STRONG.
n Water and Moisture — Never use this product around water
(near a bathtub, kitchen sink, laundry tub, wet basement,
swimming pool or in the rain)
n Location — To avoid damage to the product and prevent
personal injury, never place this product on an unstable stand,
tripod, bracket, table or cart. Mount only on a stable tripod,
stand, or bracket. Follow the instructions that describe how to
safely mount the product,and use only the mounting devices
recommended by the manufacturer
n Power Sources — Connect this product only to the power
source described on the product label. If you are not sure
about the type of power supply in your home, consult your
local power company
n Refer to instruction pages for information on using the
product with a battery
n Grounding, Polarization — If this product is used with a
specified AC adapter, the adaptermay be equipped with a
polarized alternating current line plug (a plug with one blade
wider than the other). This safety feature allows the plug to
fit into the power outlet only one way. If you cannot insert
the plug into the wall outlet, pull it out, reverse it, and then
reinsert it. If the plug still fails to fit, contact an electrician and
have the receptacle replaced
n Protecting the Power Cord — The power
supply cord should be placed so it will not
bewalked on. Never put a heavy object on
the power cord or wrap it around the leg of
a table or chair. Keep the area around the
power cord connection points, at the power
outlet, and at the product connection, free of
all AC adapter or accessory power cords
General precautions
Safety precautions
n Lightning — If a lightning storm occurs while using a specified
AC adapter, remove it from the wall outlet immediately. To
avoid damage from unexpected power surges, always unplug
the AC adapter from the power outlet and disconnect it from
the camera when the camera is not in use
n Overloading — Never overload wall outlets, extension cords,
power strips, or other power connection points with too
many plugs
n Foreign Objects, Liquid Spillage — To avoid personal injury
caused by fire or electrical shock from contact with internal
high voltage points, never insert a metal object into the
product. Avoid using the product where there is a danger
of spillage
n Heat — Never use or store this product near any heat source
such as a radiator, heat register,stove, or any type of equipment
or appliance that generates heat, including stereo amplifiers
n Servicing — Refer all servicing to qualified personnel.
Attempting to remove the covers or disassemble the product,
could expose you to dangerous high voltage points
n Damage Requiring Service — If you notice any of the
conditions described below while using a specified AC adapter,
unplug it from the wall outlet and refer servicing to qualified
service personnel:
1. Liquid has been spilled onto the product or some other
object has fallen into the product.
2. The product has been exposed to water.
3. The product does not operate normally despite following
operating instructions. Adjust only the controls described
in the operating instructions as improper adjustment
of other controls could damage the product and require
extensive repair work by a qualified technician.
4. The product has been dropped or damaged in any way.
5. The product exhibits a distinct change in performance.
n Replacement Parts — When replacement parts are required,
make sure that the authorized service center uses only
parts with the same characteristics as the originals, as
recommended by the manufacturer. Unauthorized substitution
of parts could result in fire, electrical shock, or create
other hazards
n Safety Check — Upon completion of servicing or repairs, ask
the service technician toperform safety checks to determine that
the product is in good working order
SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
CAUTION: TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS
INSIDE. REFER TO QUALIFIED SERVICE FOR SERVICING.

PART 1 • English
1
English
TABLE OF CONTENTS
1.0 INTRODUCTION 2
1.1 Safety Instructions 2
1.2 Storage 2
1.3 Equipment Set-up 3
1.4 Features & Accessories 3
2.0 YOUR RECEIVER 4
2.1 Front Panel 4
2.2 Rear Panel 4
2.3 Remote Control 5
3.0 CONNECTIONS 6
3.1 Connecting to TV & VCR 6
3.2 Connecting to Digital Audio Amplifier 6
3.3 Connecting to Satellite Dish 6
3.4 Connecting to serial cable for downloading software 7
4.0 STARTING UP 7
4.1 Language Selection 7
4.2 Select Satellite 7
4.3 Antenna mode 8
5.0 MAIN MENU 8
5.1 Channel Organiser 8
5.2 Installation 9
5.3 System setting 10
5.4 Timer 13
5.5 Game 14
5.6 Calendar 14
6.0 WATCHING TV AND LISTENING TO THE RADIO 15
6.1 Program Information 15
6.2 Mosaic (Nine picture view) 15
6.3 EPG (Electronic Program Guide) 15
6.4 Changing channel list mode between TV, Radio and Favourite 15
6.5 Selection Audio Language 16
6.6 TELETEXT function 16
6.7 Subtitles function 16
A.1 TROUBLESHOOTING 16
A.2 SPECIFICATIONS 17
A.3 GLOSSARY OF TERMS 19
* €0.12/Min. from Austrian wired line
* €0.14/Min. from German wired line
per February 2008

PART 1 • English
2
1.0 INTRODUCTION
1.1 Safety Instructions
DO NOT INSTALL YOUR RECEIVER:
n In a closed or poorly ventilated cabinet; directly on top of or under any another
equipment; on a surface which might obstruct the ventilation slots
DO NOT EXPOSE THE RECEIVER OR ITS ACCESSORIES:
n To direct sunlight or near any other equipment that generates heat; to rain or intense
moisture; to intense vibration and to any shock which may cause permanent damage to
your receiver or to any magnetic objects, such as loudspeakers, transformers, etc
n Do not use a damaged power cord. It may cause a fire or an electrical shock. Do not
touch a power cord with wet hands. It may cause an electric shock
n Never open the cover. It is dangerous to touch the inside of the receiver due to high
voltage currents and possible electrical hazards. Your warranty will be void if the receiver
has been opened
n When the receiver is not used for a long period of time, you should unplug the power
cord from the wall socket
n Do not use alcohol or ammonia based liquids to clean the receiver. If you wish, you
may clean your receiver with a soft lint-free cloth slightly made damp with a mild soap
solution, only after disconnecting from the mains voltage supply. Make sure no foreign
objects fall through the ventilation slots because this could cause fire or an electric shock
n Do not place any objects on top of the receiver because this might prevent proper cooling
of the components inside
Safety Precautions
n Do not open the receiver cover, as you will be exposed to a shock hazard. It will also void
your warranty. Refer all maintenance or servicing to suitably qualified personnel
n When you are connecting the cables, be sure that the receiver is disconnected from the
mains supply voltage. Wait a few seconds after switching off the receiver before you move
the receiver or disconnect any equipment
n It is a necessity that you only use an approved extension and compatible wiring that
is suitable for the electrical power consumption of the installed equipment. Please
ensure that the electrical power supply corresponds with the voltage on the electrical
identification plate at the back of the receiver
If the receiver does not operate normally even after strictly following the instructions in this user
manual, it is recommended to consult your dealer.
1.2 Storage
Your receiver and its accessories are stored and delivered in a packaging designed to protect against
electric shocks and moisture. When unpacking it, make sure that all the parts are included and keep
the packaging away from children. When transporting the receiver from one place to another or if
you are returning it under warranty make sure to repack the receiver in its original packaging with its
accessories. Failing to comply with such packaging procedures could void your warranty.

PART 1 • English
3
English
1.3 Equipment Set-up
We recommend you consult a professional installer to set up your equipment. Otherwise, please
follow the instructions below:
n Refer to the user manual of your TV and your antenna.
n Make sure that the SCART cable and outdoor components are in a good condition and
the SCART connections are well shielded
This manual provides complete instructions for installing and using this receiver. The following
symbols will serve as follow.
Warning Indicates warning information.
Tips Indicates any other additional important or helpful information.
MENU Represents a button on the remote control or the receiver
Move to Represents a menu item within a window.
1.4 Features & Accessories
n For all digital Free-To-Air TV and Radio programmes via satellite*
n Set-up support for first time installation & user-friendly menu
n 4 800 channel memory capacity for 64 satellites
n 3 seconds replay
n 4 Favourite lists for TV-and Radio programme
n ASTRA and HOT BIRD channels are pre-programmed
n Future-proof: Software update via satellite (OTA)
n Multi-lingual support on screen menu (OSD): English, German, French, Italian, Spanish,
Russian, Croatian, Romanian, Hungarian, Czech, Polish
n Display showing channel number or time
n Digital sound through coaxial output (S/PDIF)
n Separate power switch
n Parental lock function for menu and selectable per channel
n Teletext via OSD & VBI.Full multi-lingual DVB subtitling and audio track support
n Supports DiSEqC 1.0, DiSEqC 1.2 and GOTO X
n Electronic Programme Guide (EPG) for present/following event information and up to 7
days for on screen programme information
n Automatic, network and manual channel scan options
n 10 Timer for recording and/ or sleep-timer with 3 modes (daily, weekly, once)
n Mosaic function: 9 TV Channel in overview
n 5 Games (Boxman, Mine, Tetris, Rush Hour, Gomoku)
n Signal strength bar for digital transponders
n Connections: SAT IN, SAT OUT, 1 Scart TV (RGB/CVBS), 1 Scart VCR (CVBS), 3 RCA
(Video, Audio Left & Right ), S/PDIF, Serial Port RS-232, Power switch
* subject of local broadcast condition

PART 1 • English
4
Accessories:
n User’s Manual
n 1 Remote control unit
n 2x Batteries (AAA type)
Note: The batteries should not be recharged, disassembled, electrically short-circuited or
be mixed or used with other types of batteries.
2.0 YOUR RECEIVER
2.1 Front Panel
1. Mode indicator
The RED light indicates that the receiver is in STAND-BY mode. The GREEN light indicates that the
receiver is in AWAKE mode.
2. Power On/Off button
3. Channel Up/Down buttons
4. 4 digits display In STAND-BY mode this indicates current time
In AWAKE mode this indicates current channel number
2.2 Rear Panel
Fig. 2
1. SAT IN
Connect the digital signal from your LNB on the satellite dish to this connector.
2. SAT OUT
Gives you the possibility to connect an extra receiver (analogue or digital).
3. TV SCART Connector
To connect your receiver to your TV set using a SCART cable.
4. Video RCA Connector
To connect your receiver to your TV set using RCA cable
5. Audio Left/Right RCA Connector
To connect your receiver to your TV set or amplifier using RCA cable
6. RS-232 Serial Port
This serial port can be used to connect your PC with your receiver, to download new
versions of software to your receiver.
7. Power Cord
Your receiver requires a voltage of 90 ~ 240 V AC (Auto-selectable), 50 ~ 60Hz ±5%. Make
sure to check the power specification before connecting your receiver to the wall outlet.
8. VCR SCART Connector
To connect your receiver to your video recorder using a scart cable. Your video signal will
now be looped through your receiver to your TV set.

PART 1 • English
5
English
9. S/PDIF Digital audio output
Use this coaxial output to connect your receiver to the input of your digital audio amplifier.
10. Power ON/OFF Switch
2.3 Remote Control
Turns the receiver On/Off
Mutes audio output of the receiver
AV Toggle between TV and AV mode
0 ~ 9 Changes channel and controls numeric functions
FAV Toggle Favourite mode ON / OFF
TV/R Toggle between TV or RADIO mode
MENU Shows the main menu and exits from any level of menu
to view mode
INFO Shows information of the current channel
EPG Shows the EPG (Electronic Program Guide) only when
menu is off
EXIT Exits from the menu or sub-menu and cancels the
progressing function if applicable
pq Menu Off: Change the current program to the
previous/next program when menu is off.
Menu On: Moves the cursor up/down when menu
is on.
tu Menu Off: Increases/decreases the volume level
when menu is off.
Menu On: Change the setting values in specific
Menu item when menu is on.
OK Activates the highlighted menu item. Displays a channel
list according to TV / Radio Mode
V+ / V- Use to increase or decrease the receiver volume level
P+ / P- Page up and down in menu list
MOSAIC Show pictures of 9 channels on the screen simultaneously
PAUSE Freeze/Resume picture
AUDIO Shows list of available audio languages for the channel
you are watching. In addition it sets the current channel
audio to stereo ((•)), left-mono ((• or right-mono •))
EDIT Program edit
REPLAY Replay last 3 seconds of current channel
TEXT Shows current service’s Teletext on OSD (On Screen Display)
SUB Show list of subtitled languages current channel is supporting
RCL Switches back to previous channel viewed

PART 1 • English
6
3.0 CONNECTIONS
3.1 Connecting to TV & VCR
Basic connection with a Scart cable
Fig. 3
1. Connect the satellite signal from the LNB to the LNB IN connector.
2. Connect the TV SCART connector at the back of the receiver to the SCART IN connector
on your TV set.
Basic connection with a RCA cable
Fig. 4
1. Connect the satellite signal from the LNB to the LNB IN connector.
2. Connect the Video RCA connector at the back of the receiver to the Video IN RCA
connector on your TV set.
3. Connect the Audio Left and Right RCA connectors at the back of the receiver to the Audio
Left and Right IN connectors on your TV set or audio amplifier.
Advanced connection of the receiver to the TV set and VCR
Fig. 5
1. Connect the satellite signal from the LNB to the LNB IN connector.
2. Connect the TV scart connector at the back of the receiver to the scart-in connector on
your TV set.
3. Connect the VCR scart connector at the back of the receiver to the scart-in connector on
your VCR.
3.2 Connecting to Digital Audio Amplifier
Fig. 6
Connect your Digital Audio Amplifier with the S/PDIF connector on the back of the receiver.
3.3 Connecting to Satellite Dish
Connecting a fixed satellite dish to your receiver
Fig. 7
First choose a satellite you want to receive your signals from, and have your dealer aim your dish at
the requested satellite.
Connect a coax cable to your LNB and the other end directly to the LNB IN connector of your receiver.
Connecting multiple fixed dishes to your receiver using a DiSEqC 1.0 switch (Fig. 8)
If you want to watch programs from more than one satellite (For example from ASTRA and from
HOT BIRD) it is advisable to use fixed dishes and a DiSEqC 1.0 switch. Have your Dealer aim the
dishes at the requested satellites and connect the LNB’s with coax cables to the IN connectors
of the DiSEqC 1.0 switch. Connect the OUT connector of the DiSEqC 1.0 switch to the LNB IN
connector at the back of your receiver.

PART 1 • English
7
English
Connecting a dish on a motorized positioner to your receiver (Fig. 9)
Fig. 9
Another possibility for watching programs from multiple satellites is by mounting a dish to a
motorized DiSEqC 1.2 positioner. Have your dealer mount the dish to the positioner, set the correct
angle of the elevation and let him set the center point for your positioner. Connect the LNB with
a coax cable to the LNB IN connector of the positioner, and connect the OUT connector of the
positioner to the LNB IN connector at the back of your receiver.
3.4 Connecting to serial cable for downloading software
Fig. 10
Connect the RS-232 connector on the back of your receiver to the Serial port of your computer using a
serial cable. Instructions how to download software can be found on our website www.strong.tv (support
> download). However, this receiver can download new system software automatically by satellite.
4.0 STARTING UP
Ensure your satellite receiver is correctly connected to your television and dish, and that your
satellite signal is of good quality. (If you are not sure about this then ask your local STRONG
dealer to check your installation or satellite signal.) Confirm that the power plug on the receiver is
plugged into the wall outlet. Turn on the receiver. It is recommended that you perform the first time
installation following the Installation Wizard step by step. It will help you to easily achieve system
configuration and channel installation. If you are a professional installer then you can skip wizard by
pressing MENU button and set-up channels using the Installation menu.
4.1 Language Selection
Press UP/DOWN to choose your language, press OK to confirm. The Select Satellite menu will
appear. Future installation steps are depending from satellite where your dish is aimed.
4.2 Select Satellite
a) Your dish is aimed to ASTRA 1C, 1E, 1F or HOT BIRD satellite.
Press UP/DOWN to select the ASTRA or HOT BIRD satellite and press OK button. Follow the
instructions. When you have fixed your dish at correct direction choose NEXT and press the OK
button. The Channel Setup menu will appear.
b) Your dish is aimed at another satellite
Select Other in Select satellite menu and press OK, more satellites will be listed. If you select one out
of the satellite list, the Configure Antenna menu will appear, please set the LNB Type, LNB Low Freq,
LNB High Freq, Band control, Polarisation control, DiSEqC Switch and Antenna mode.

PART 1 • English
8
4.3 Antenna mode
a) Fixed dish
Set Antenna mode to Fixed, select NEXT and press the OK button. The Adjust antenna screen appears,
select transponder receivable at your location and adjust the antenna position for maximum level for
the signal strength and quality. When you have completed the adjustment, choose NEXT and press
the OK button. The Channel Setup menu will appear
b) Dish mounted on DiSEqC 1.2 motor
Set Antenna mode to DiSEqC 1.2, choose NEXT and press the OK button. The menu Adjust antenna
will appear. Select transponder receivable at your location (choose Transponder field and select
transponder by pressing LEFT/RIGHT button). Then choose field Move Dish and adjust position
of the dish by pressing the LEFT/RIGHT button. Once you adjust the dish position choose Store
position, set number of the position by pressing LEFT/RIGHT button. Then choose NEXT and press
the OK button. The Channel Setup menu will appear.
c) Dish mounted on GOTO X motor
Set Antenna mode to GOTO X, choose NEXT and press the OK button. The menu Adjust antenna
will appear. Select transponder receivable at your location (choose Transponder field and select
transponder by pressing LEFT/RIGHT buttons). Then choose field My Longitude and using numeric
buttons enter value of your longitude. Use LEFT/RIGHT buttons to select hemisphere East or West.
Then choose field My Latitude and using numeric buttons enter value of your latitude. Use LEFT/
RIGHT buttons to select hemisphere Nord or South. Choose field Goto Position and press OK. Your
dish will be turned to the position of satellite. Then choose NEXT and press the OK button. The
Channel Setup menu will appear.
Choose NEXT and press the OK button to start the scan. When the scan is completed, the receiver will
save the services information automatically and exit to the normal play state.
5.0 MAIN MENU
All the important settings and features of your receiver can be operated in Main Menu. The Main
Menu consists of five sub-menus which are "Channel Organizer", "Installation", "System setting",
"Timer" and "Game".
Press the MENU key when the menu is off, The MAIN MENU screen will appear.
5.1 Channel Organiser
In MAIN MENU screen, press UP/DOWN to move the cursor to Channel Organiser, and then press
OK to enter the Channel Organiser menu, which consists of two sub-menus; “Channel Manager” and
“Favourites Manager”.
5.1.1 Channel Manager
In this menu, you can change the order of the channels, move, delete and edit channels. To change
the satellite use the RED button.
n Sort (GREEN buton)
You can sort the channel order in the channel list by “Name a~z”, “Name z~a”,“Free-CA”, “Fav – NO
Fav” or “Default” type.

PART 1 • English
9
English
n Edit (YELLOW button)
Select the channel that you wish to edit, press the YELLOW (Edit) button to move into the modify
program menu. In this menu, you can modify the Program Name, Down Frequency, Symbol rate,
Video PID, Audio PID.
If you want to rename the channel, use the UP/DOWN keys to select “Program Name” and press
OK, the program name dialog will shown as below.
Use the LEFT/RIGHT buttons to move the cursor to the character you wish to edit. Use the UP/
DOWN buttons to change character (scroll alphabet). If you wish to delete character you have to
replace it with “space” character. When editing is complete, press the OK button.
n Move channel
Press the UP/DOWN keys to point the focus of the menu to the channel of your selection. Press
the LEFT/RIGHT keys to point the focus of the menu to the column “Move”. When the focus is on
column “Move”, press the OK button to confirm selection of the channel, using the UP/DOWN
buttons move the channel to its new location and press the OK button to confirm the new location.
Repeat this for every channel that you want to move.
n Delete channel
Press the UP/DOWN keys to point the focus of the menu to the channel of your selection. Press the
LEFT/RIGHT keys to point the focus of the menu to the column “Del”. When the focus is on column
“Del”, press the OK button to mark the channel as selected to be deleted from the list. To apply the
changes press the EXIT button and confirm the channel’s deletion.
n Delete All channels
To delete all channels from current satellite press BLUE button (Dell All). You will be asked to confirm operation.
5.1.2 Favourites Manager
Press the UP/DOWN keys to select the channel. Press the LEFT/RIGHT keys to point the focus to
the favourite group. Press the OK button to add the selected channel to the Favourite group. To
remove the channel from the favourite group, repeat same operation.
5.2 Installation
The installation menu contains three sub-menus; “Antenna Installation”, “Auto Scan” and “Manual Scan”.
5.2.1 Antenna Installation
You can add a satellite, edit a satellite and delete a satellite in this menu.
n Add satellite
If you want add a new satellite, press the RED key in this menu, a satellite list will appear on the screen.
Press RIGHT/LEFT to select the satellite. If the satellite does not exist in the satellite list, please select
“NEW SAT1”. After selection of a satellite from the satellite list, the Configure Antenna menu will appear,
please set the LNB Type, LNB Low Freq, LNB High Freq, Band control, Polarisation control, DiSEqC
Switch and Antenna mode. Further steps of installation are described in 4.2.
n Edit satellite
If the parameters of the satellite were changed or the satellite is a new satellite, you must set the parameters of
the satellite, such as LNB type, LNB low Freq, LNB High Freq, Transponder, LNB Power, 22k Tone, DiSEqC and
Antenna Mode. Sequence of editing of satellite parameters is same as sequence of “Add satellite” described in 4.2

PART 1 • English
10
n Delete satellite
If you want to delete a satellite, press the YELLOW key. Then warning message will appear. Select
OK and press the OK key to confirm.
5.2.2 Auto Scan
Press the GREEN key to set the scan mode to Free or Free+Scrambled. If mode is Free then only “Free
to Air” channels will be added to the channel list. If mode is Free+Scrambled then all channels from
selected satellite will be added to the channel list.
Press the YELLOW Key to set the Blind Scan to ON or OFF. Blind scan function is useful to scan
new added satellite, but scan may take long time.
Press the BLUE Key to set the scan type to NIT OFF or NIT ON while Blind Scan is set to OFF and
to Quick Search or Detail Search while Blind Scan is set to ON.
When the set-up is completed, press the RED key to start the scan, shown as below.
5.2.3 Manual Scan
In this menu, you can scan single transponder, add a new transponder, edit the transponder or
delete the transponder.
You can switch between satellites with the RED button,
Scan transponder:
Use UP/DOWN buttons to select the transponder. Press OK button to start scan.
Add Transponder:
In this menu, you can add a new transponder to the system. Press the GREEN button, the Add
Transponder sub-menu will appear.
Frequency: input the frequency of the new transponder.
Symbol Rate: input the symbol rate of the new transponder.
Polarity: Select the Polarity of the new transponder.
Edit Transponder:
In this menu, you can edit a transponder in the system. Press the YELLOW button, the Edit
Transponder sub-menu will appear. This menu is similar to Add Transponder menu.
Delete Transponder
Press the BLUE button to delete a transponder. You will need to confirm operation.
Press LEFT/RIGHT to select OK, press the OK button to confirm.
5.3 System setting
In this menu, you configure the system, such as Language Setting, OSD style, Parental Control, TV
Settings and Time Setting.

PART 1 • English
11
English
5.3.1 Preference
5.3.1.1 Language Setting
You can change the language of the OSD, preferred Audio and Subtitles.
Use UP/DOWN to select the OSD language, Audio language or Subtitles language. Press OK or Right
to enter the language list and Press UP/DOWN to select the language. Press OK to confirm.
5.3.1.2 TV settings
You can set the TV mode, Screen mode and Video output.
n TV mode
In TV mode Screen press OK or RIGHT to select mode, press OK to confirm. If you don’t
know which standard your TV has, please select AUTO.
n Screen mode
In TV format Screen press OK or RIGHT to select 4:3 or 16:9, press OK to confirm.
n Video output
In Video output Screen press OK or RIGHT to select CVBS or RGB, press OK to confirm.
5.3.1.3 Time Settings
If a broadcaster provides GMT, you can set the time using GMT, or set your own time by yourself.
If the GMT usage is ON then you have to set the Time Zone. If you set GMT Usage to OFF, Set Data
and Set Time item are displayed. To set the time value manually, move the cursor to the time item
and use the numeric buttons on the remote control.
5.3.1.4 Set Factory Default
Please be careful when using this function, because it will erase all the data and parameters you
may have set earlier to your receiver. Once you set the factory default you will have to re-install your
preferences and re-scan your channels. To reset your receiver to factory default, apply the following steps:
Select Set Factory default and press OK. Confirm warning message with OK and press the OK key,
the receiver will return to its factory default state, and all user data will be deleted.
NOTE: Your PIN code will change back to the factory setting “0000”.
5.3.2 OSD Style
In this menu, you can set the Menu Colour, Transparency Level and Border Pattern.
5.3.3 Parental Control
In this menu, you can set Channel Lock status (ON or OFF), the Menu Lock status, Parental Setting
and change the PIN code.
The default PIN code is 0000.
5.3.3.1 Channel Lock
Set the system Channel Lock to ON or OFF. If the channel lock is on, the user has to enter the
parental PIN code correctly before watching the locked channel.

PART 1 • English
12
5.3.3.2 Menu Lock
Press OK to select whether you need the lock or not for the Menu, YES or NO, press OK to confirm.
If the menu lock is on, then for some operations such as search program and set factory default,
you need to enter your PIN.
5.3.3.3 Parental Setting
Set some channels to lock status. If a channel is locked, the user has to enter the parental PIN code
correctly before watching the locked channel. Use the UP/DOWN keys to select the channel you
want to lock. Press the OK button to lock the channel.
5.3.3.4 Change PIN
Modifying the PIN, you must enter the 4 digits PIN and confirm it again; the system PIN will be
changed to the new PIN.
5.3.4 System info
The system information displays information about your receiver such as software and User
Interface version. Compare version of the software given on this menu with version available in the
internet in order to know if you have latest version of software.
5.3.5 System Update
In this menu, you can select between “STB to STB” and “OAD”
5.3.5.1 STB to STB software transfer
1. First power off both STBs, connect them with cross RS-232.
2. Then power on master STB (master is STB from which you will copy software) and keep
slave STB off. Navigate in the menu of master STB and select
“System Update – STB to STB”.
3. When the status displays “detecting slave STB”, power on slave STB, after the master
STB detects the slave, the master starts transmission and burns.
4. While transmitting and burning, it is very important to avoid other operations such as
power off because this may cause destruction of the data in the FLASH memory and the
receiver will need to be repaired.
5. When update is complete, first power off both STBs, then disconnect the RS-232 line.
5.3.5.2 Over Air Download (OAD)
Select this option in order to update your receiver with the latest software version. Software update
service is available from satellites ASTRA 1C, 1E, 1F at 19E and HOT BIRD 1, 2, 3, 4 at 13E.
If your antenna is primed to ASTRA 1C, 1E, 1F at 19E then enter following parameters:
Frequency: 12603; Polarity: H (Horizontal); Symbol rate: 22000
If your antenna is primed to HOT BIRD 1, 2, 3, 4 at 13E then enter following parameters:
Frequency: 12476; Polarity: H (Horizontal); Symbol rate: 27500
Move menu focus to OK and press OK button on remote control. The receiver will check availability
of the software update on air and load the latest software, if available. Do not switch power off and

PART 1 • English
13
English
do not disconnect the receiver from the aerial during update process. Availability of the software
update is subject of local broadcast condition and may not work in all countries. Contact your
vendor to find out more about this function.
5.3.5.3 Update through PC to STB
1. Connect Computer to receiver (receiver must be power off) with a 9-pin cross cable
(two females).
2. The computer will follow the steps below:
Start->Programs->Accessories->Communications->Hyper terminal
Then choose “COM1” or “COM2” according to which port you are using in the computer
and port setting as follows:
Bits per Second: 115200
Data bits: 8
Parity: None
Stop bits: 1
Flow Control: None
3. In Hyper Terminal menu select “transfer” item and then press “send file” item. Select the
file with the new software (*.UPD) you want to download and choose the protocol
“1K X modem”. Finally press OK and a download menu will appear on the computer
screen. Power on the receiver, then the download process will start.
4. After about 2.5 minutes, the message “OK, Reset” will appear on the computer on Hyper
Terminal window, which means the download has completed successfully.
5. Power off the receiver and then unplug the RS-232 interface.
NOTE: INCORRECT OPERATION MAY CAUSE UNREPAIRABLE DAMAGE TO THE RECEIVER.
1. DO NOT POWER OFF THE RECEIVER DURING THE PROCESS OF DOWNLOAD.
2. DO NOT PLUG IN OR UNPLUG THE RS-232 INTERFACE WHEN RECEIVER IS
POWERED ON
5.4 Timer
You can set the timer to make the receiver perform designated actions including timer based wake
up or sleep instructions to the receiver.
Use the UP/DOWN buttons to select timer. Press the RED key to activate/inactivate current timer.
Press the OK button to enter your selected timer settings.
Action: You can select the following functions:
“Power On”: The receiver powers on at the designated date and time within defined channel.
“Time interval”: The receiver switches on at the designated date and time, displays the channel and
then switches off at the designated date and time (The value set at the end time).
“Power Off”: The receiver powers off at the designated date and time.
Cycle: You can set the cycle of the action designated in the timer mode (One time, Daily
or Weekly).
Start Date: You can set the start date of the timer action.

PART 1 • English
14
Start Time: You can set the start time of the timer action.
End Time: You can set the end time of the channel viewing when the Timer mode is on
Time Interval.
Channel Type: Select between TV and Radio.
Channel name: Press the RIGHT button to display the channel list and using navigation buttons
select the channel to be shown when the receiver will power on by the timer.
5.5 Game
The receiver has five games (Boxman, Mine, Tetris, Rush Hour and Gomoku) and a calendar. In this
menu user can select any game item and press OK to play the game. Or you can press the GAME
key in normal play state into the game menu directly.
5.5.1 Boxman
UP/DOWN/LEFT/RIGHT key to move the cursor to push the box.
EXIT to exit from game.
5.5.2 Mine
UP/DOWN/LEFT/RIGHT key to move the cursor.
MENU button: To mark the mine.
OK button: to open cell
5.5.3 Tetris
LEFT/RIGHT key to move the block to left or right.
DOWN to drop the block.
UP to Rotate the block.
5.5.4 Rush Hour
Press UP/DOWN/LEFT/RIGHT keys to move the cursor, and press OK to select the object.
5.6 Calendar
UP / DOWN: next/previous months.
LEFT / RIGHT: next/previous years (range from 1900 to 2100).

PART 1 • English
15
English
6.0 WATCHING TV AND LISTENING TO THE RADIO
6.1 Program Information
In normal operation status (no menu operation), press the INFO button. The program information banner
will be displayed at the bottom of screen. From program information banner you can read channel number,
channel name, current and next program name (if available from broadcast) and current time.
To check technical information about channel press INFO button twice, the Program Information
menu will appear on screen. In this menu, the user can view the current program information such
as the satellite name, program name, program number, local frequency, polarity, 22K tone, DiSEqC,
down frequency, symbol rate, video PID and audio PID. You also can view the signal strength of the
current program and its signal quality.
6.2 Mosaic (Nine picture view)
In normal operation status (no menu operation), press the MOSAIC button, there are nine picture
being showing on screen.
6.3 EPG (Electronic Program Guide)
The EPG shows a programs schedule of the channels.
Note: not all the broadcasters do provide a programme information.
From normal view mode press the EPG button. The EPG Menu will appear.
Press UP / DOWN to choose the channel. Press RIGHT to display programs schedule of the current channel.
1. In EPG programme schedule menu: Press the UP / DOWN keys to choose the program
items. Press LEFT/RIGHT keys to get programs schedule for previous/next dates. Press
EXIT to return to EPG Menu. Press GREEN to display the details of current program.
2. In program details:
Press UP / DOWN to scroll information (next / previous page). Press LEFT or EXIT to
return to the EPG schedule Menu.
3. Programming Timer from EPG
You can set up the event timer by pressing RED button or OK button from the EPG
program schedule. To set up a timer event:
Press UP/DOWN to move the cursor to the program for which you want to add a timer.
Press RED button to add a timer. You can also use this screen to modify each value. To
save the settings, press OK. To quit event timer setup, press EXIT.
6.4 Changing channel list mode between TV, Radio and Favourite
To change between TV and Radio channel lists use TV/R button from normal operation mode or
from channel list mode. To change channel list to favourite mode press FAV button from normal
operational mode. Use LEFT/RIGHT buttons to select favourite group. Press OK to confirm
selection. Then select channel of your choice and press OK to switch to full screen mode. If you
wish to select another favourite group of channels or exit from favourite channel list mode – press
FAV button. List of favourite channels will appear on screen. Press RED or FAV button to move
menu focus to selection of group. Use LEFT/RIGHT buttons to select group of your choice. Select
group “NO FAV” and press OK if you wish to exit from favourite channel list mode.