TechniSat MultyMedia TS 1 User manual

Bedienungsanleitung
with integrated
CONAX decoding system and
PCMCIA slot for
insertion of a CI module.
For reception of free-to-air and encrypted
(e.g. CONAX, CRYPTOWORKS, VIACCESS,
IRDETO, SECA etc.)
satellite and DVB-T programmes.
Operating Manual
MultyMedia TS 1
Features motor antenna controls and
software update via satellite / antenna.
BED_AN_Multymedia_TS1 2Q4eng 29.03.2006 10:40 Uhr Seite 1

1 Contents
1 Contents . . . . . . . . . . . . . . . . . . . . . . . . . .2, 5
2 Illustrations . . . . . . . . . . . . . . . . . . . . . . . . .3
Important notes on operation . . . . . . . . . . . . . . . . . . .8
Disposal instructions . . . . . . . . . . . . . . . . . . . . . . . . . .8
Safety advice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
4 Connecting the DVB Receiver . . . . . . . . .10
4.1 External unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
4.2 Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
4.3 Connection to a television set . . . . . . . . . . . . . . . . . .11
4.4 Video cassette recorder (VCR) . . . . . . . . . . . . . . . . .11
4.5 Hi-Fi amplifier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
4.5.1 Analogue . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
4.5.2 Digital . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
4.6 Serial interface (RS 232) . . . . . . . . . . . . . . . . . . . . . .12
4.7 Mains power connection . . . . . . . . . . . . . . . . . . . . . .12
5 Initial installation . . . . . . . . . . . . . . . . . . . .12
6 Settings . . . . . . . . . . . . . . . . . . . . . . . . . . .17
6.1 Operating language . . . . . . . . . . . . . . . . . . . . . . . . . .17
6.2 Basic settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
6.2.1 Time difference to GMT (hours) . . . . . . . . . . . . . . . .18
6.2.2 Country . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
6.2.3 Remote control code . . . . . . . . . . . . . . . . . . . . . . . . .18
6.2.4 Stand-by clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
6.3 Audio/Video settings . . . . . . . . . . . . . . . . . . . . . . . . .19
6.3.1 Picture format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
6.3.2 Language (Audio signal/sound-track) . . . . . . . . . . . .20
6.3.3 Language (sub-titles) . . . . . . . . . . . . . . . . . . . . . . . . .20
6.3.4 TV SCART mode . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
6.3.5 VCR SCART mode . . . . . . . . . . . . . . . . . . . . . . . . . .20
6.3.6 Dolby Digital (AC3) . . . . . . . . . . . . . . . . . . . . . . . . . .21
6.4 Antenna settings (DVB-S) . . . . . . . . . . . . . . . . . . . . .22
6.4.1 Multytenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
6.4.2 Switching DiSEqC on and off . . . . . . . . . . . . . . . . . .22
6.4.3 Setting the switching matrix . . . . . . . . . . . . . . . . . . . .23
6.4.4 Additional settings/LNB characteristics . . . . . . . . . . .23
6.4.5 Rotating antenna unit . . . . . . . . . . . . . . . . . . . . . . . .25
6.5 Antenna settings (DVB-T) . . . . . . . . . . . . . . . . . . . . .25
7 Operation . . . . . . . . . . . . . . . . . . . . . . . . . .26
7.1 Switching on and off . . . . . . . . . . . . . . . . . . . . . . . . .26
7.2 Programme selection . . . . . . . . . . . . . . . . . . . . . . . . .26
7.2.1 Using the programme keys up/down . . . . . . . . . . . . .26
7.2.2 Using the numeric keys . . . . . . . . . . . . . . . . . . . . . . .26
7.2.3 Using the Navigator (programme list) . . . . . . . . . . . .27
7.2.4 Calling up blocked programmes . . . . . . . . . . . . . . . .27
2
BED_AN_Multymedia_TS1 2Q4eng 29.03.2006 10:40 Uhr Seite 2

7.2.5 Infobox . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
7.3 Receiving encrypted programmes . . . . . . . . . . . . . .28
7.3.1 Special functions . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
7.3.2 CONAX PIN code . . . . . . . . . . . . . . . . . . . . . . . . . . .30
7.4 Volume control . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
7.5 TV/Radio switching . . . . . . . . . . . . . . . . . . . . . . . . . .30
7.6 Selecting a different language . . . . . . . . . . . . . . . . .31
7.6.1 Dolby Digital (AC3 mode) . . . . . . . . . . . . . . . . . . . . .31
7.7 Return to last programme selected . . . . . . . . . . . . . .32
7.8 Display clock and programme information . . . . . . . .32
7.9 Additional programme information . . . . . . . . . . . . . .32
7.10 Transponder information . . . . . . . . . . . . . . . . . . . . . .32
7.11 Freeze frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
7.12 Sleep timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
7.13 Videotext . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
7.14 Sub-titles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
7.15 Electronic Programme Guide SFI (SiehFern Info) . .35
7.15.1 Downloading SFI data . . . . . . . . . . . . . . . . . . . . . . . .35
7.15.2 Interrupting the download procedure . . . . . . . . . . . .35
7.15.3 Calling up the Electronic Programme Guide . . . . . .36
7.15.4 Now (table with current programme contents) . . . . .36
7.15.5 Next . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
7.15.6 More . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
7.15.7 SFI functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
7.15.8 Ending SFI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
7.16 Timer recordings . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
7.16.1 Programming the timer manually . . . . . . . . . . . . . . .41
7.16.2 Timer overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
7.16.3 Changing the timer programming . . . . . . . . . . . . . . .43
7.16.4 Deleting the timer programming . . . . . . . . . . . . . . . .43
7.16.5 Programming a new timer event . . . . . . . . . . . . . . . .44
8 Changing the basic programming . . . . . . .44
8.1 Configuring the Favourites list . . . . . . . . . . . . . . . . .44
8.1.1 Calling up the programme list manager . . . . . . . . . .45
8.1.2 Add programmes to Favourites list . . . . . . . . . . . . . .46
8.1.3 Deleting programmes . . . . . . . . . . . . . . . . . . . . . . . .47
8.1.4 Sorting programmes . . . . . . . . . . . . . . . . . . . . . . . . .48
8.2 Programming the Electronic Programme Guide . . . .49
8.2.1 Updating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49
8.2.2 Updating time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49
8.2.3 SFI channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50
8.2.4 Selecting channels . . . . . . . . . . . . . . . . . . . . . . . . . .50
8.2.5 Start category . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
8.2.6 Manual updating of SFI data . . . . . . . . . . . . . . . . . .52
8.3 Parental control . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53
8.3.1 PIN query mode . . . . . . . . . . . . . . . . . . . . . . . . . . . .53
8.3.2 Changing the unit PIN . . . . . . . . . . . . . . . . . . . . . . . .53
5
BED_AN_Multymedia_TS1 2Q4eng 29.03.2006 10:40 Uhr Seite 3

8.3.3 Selecting a channel . . . . . . . . . . . . . . . . . . . . . . . . . . .54
8.4 Programme scan . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55
8.4.1 Automatic scan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56
8.4.2 Expanded scan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56
8.4.3 Manual search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58
8.4.4 PID search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59
8.4.5 After the scan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
8.5 Service settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61
8.5.1 Activating factory default setting . . . . . . . . . . . . . . . . .61
8.5.2 Delete all programmes . . . . . . . . . . . . . . . . . . . . . . . . .62
8.5.3 Update programme list (ISIPRO) only DVB-S . . . . . . .62
8.5.4 Update software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65
8.5.5 Copy settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67
8.6 System configuration . . . . . . . . . . . . . . . . . . . . . . . . . .67
8.7 Encryption system . . . . . . . . . . . . . . . . . . . . . . . . . . . .68
9 Operating a rotating antenna (DiSEqC 1.2) .68
9.1 East and West limits . . . . . . . . . . . . . . . . . . . . . . . . . .69
9.1.1 Delete existing limits . . . . . . . . . . . . . . . . . . . . . . . . . .69
9.1.2 Set Eastern limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69
9.1.3 Set Western limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70
9.2 Geo-Positioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70
9.3 Setting a satellite position . . . . . . . . . . . . . . . . . . . . . .71
9.3.1 Selecting a satellite position . . . . . . . . . . . . . . . . . . . .72
9.3.2 Positioning the satellite antenna . . . . . . . . . . . . . . . . .73
9.3.3 Saving a satellite position . . . . . . . . . . . . . . . . . . . . . .74
9.4 Current satellite list . . . . . . . . . . . . . . . . . . . . . . . . . . .75
9.4.1 Turning to a satellite position . . . . . . . . . . . . . . . . . . . .75
9.5 Deleting a satellite position . . . . . . . . . . . . . . . . . . . . .75
9.6 Reference position . . . . . . . . . . . . . . . . . . . . . . . . . . . .76
10 Technical terms . . . . . . . . . . . . . . . . . . . . . .76
11 Technical data . . . . . . . . . . . . . . . . . . . . . . .79
12 Trouble-shooting guide . . . . . . . . . . . . . . . .82
13 Annexure . . . . . . . . . . . . . . . . . . . . . . . . . . .84
14 Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .86
6
Your receiver bears the CE symbol and complies with all requisite EU stan-
dards.
Not responsible for printing errors. Subject to change without notice. Correct as
at 03/06
TechniSat and MultyMedia TS 1 are registered trademarks of
TechniSat Digital GmbH
Postfach 560
D-54541 Daun/ Germany
www.technisat.de
Technical Hotline
0180/5005-910* (from Germany only)
*0,12 EUR/min. via the Deutsche Telekom AG network
BED_AN_Multymedia_TS1 2Q4eng 29.03.2006 10:40 Uhr Seite 4

3
2 Illustrations
*This function is only available where the corresponding data is broadcast by the channel
on the programme slot selected.
Remote control
Sound On/Off
SFI
Programme -
Volume -
Programme +/-
Programme +
Videotext*
On/Mix/Off
Arrow key left
Arrow key up
Arrow key down
Sleep timer
Option*
inTV mode:
Select sound track/sub-
titles, special functions
in Radio mode: Select
stations by switching sound
sub-carriers
Numeric keys
On/Stand-by
Programme list On/Off
Back
Info
Stop/Freeze frame
Menu On/Off
EXTERNAL
Multi-function keys
TV/Radio
Volume +
Volume +/-
OK
Arrow key right
OPT
Fernbedienoption:
Durch Umschalten der Fernbedienoption können mit dieser Fernbedienung zwei Receiver,
ein Fernsehgerät sowie ein weiters Gerät mit gleicher Codierung bedient werden.
> Zur Umstellung der Fernbedienoption drücken Sie gleichzeitig die gewünschte
Taste (SAT1, SAT2, VCR oder TV) und OK!!!
Beachten Sie:
Zur Bedienung dieses Receivers, müssen die hier gewählte Fernbedienoption der
Fernbedienung und der nach Punkt 6.2.3 eingestellte Fernbediencode übereinstimmen.
Remote control option:
By changing/switching the remote control option, you can use this remote control unit to
control two TechniSat receivers and a TechniSat television set using the same coding
bedient werden.
> To change the remote control option, simultaneously press the desired key
(SAT1, SAT2 or TV)and OK!!!
Please note:
To operate this receiver, the remote control option selected for the remote control and
the remote control code selected in accordance with Point 6.2.3 must agree.
BED_AN_Multymedia_TS1 2Q4eng 29.03.2006 10:40 Uhr Seite 5

4
LNB
input
Input
terrestrial
antenna
SCART socket
TV
Audio output
digital (optical)
SCART socket
VCR
DC input socket for
mains adapterl
Inserting the CI module:
> Follow the instructions given by the manufacturers
of the CI module and of the card.
> Insert the desired Smartcard into the corres-
ponding module.
> Now insert the CI module carefully into the slot.
RS 232
interface
Audio outputs
analogue
Audio output
digital (electrical)
Programm selec-
tor up/down On/Stand-by
LED display
Card reader for CONAX Smartcard:
> Insert the CONAX Smartcard (with the gold chip pointed down and
in the direction of insertion) carefully into the card reader as far as
is possible.
BED_AN_Multymedia_TS1 2Q4eng 29.03.2006 10:41 Uhr Seite 6

7
Dear customer,
congratulations on your decision to purchase the MultyMedia
TS 1 digital receiver.
The operating manual supplied is intended to help you tuilise
the comprehensive functions of your new digital receiver to the
fullest extent.
We have kept the operating instructions as brief as possible,
and have used terminology that everybody can understand.
The range of functions of your receiver is constantly being
expanded in the form of software updates. This means that
additional steps in the operation may be added that are not yet
described in this operating manual, or the operation of existing
functions may be changed. For this reason you should occa-
sionally visit the TechniSat homepage, to download the current
version of the operating manual.
We wish you many years of viewing pleasure with your
TechniSat
MultyMedia TS 1!
Your
TechniSat Team
BED_AN_Multymedia_TS1 2Q4eng 29.03.2006 10:41 Uhr Seite 7

3 Please read this first
> Before starting to use your receiver, please check that all
the components have been supplied correctly. The follo-
wing should be included:
1 digital receiver, 1 mains adapterr and connection cable,
1 remote control, 1 operating manual,
1 guarantee card, 2 batteries (1,5V microcells)
1 SCART cable.
> Please insert the batteries supplied in the battery compart-
ment of the remote control unit, with attention to the cor-
rect polarity as indicated.
Important notes on operation
The use of so-called "On Screen Displays" (OSD) means that
operation of the digital receiver is simplified, and the number of
keys on the remote control unit reduced. All functions are display-
ed on screen, and can be controlled by means of a few simple
keystrokes. Functions that are logically connected are combined
in a "MENU". Any function selected will be indicated in a different
colour. The function keys red, yellow, blue and green are indica-
ted by coloured bars at the bottom of the screen. In the various
menues, these coloured bars represent different functions, which
can be implemented by pressing the appropriate coloured keys
(multi-function keys) on the remote control. The function keys are
only activated when a brief description is displayed in the appro-
priate field.
Key names and terms that appear in the OSD menu are shown
in black type in this operating manual.
Help: where available, press the blue function key in the
menues to display a help text; press again to close the help win-
dow.
Disposal advice
The packaging material of your receiver consists entirely of recy-
clable materials. Please sort the components appropriately, and
dispose of them in line with your local waste disposal regulations.
At the end of its useful life span, this receiver may not be dispo-
sed of in your regular domestic refuse bin. It must be taken to a
recycling collection point for electrical and electronic equipment.
The symbol on the product, the operating manual or the packa-
ging will indicate this.
The materials used are recyclable and re-usable in accordance
with their labelling. By ensuring that valuable raw materials are
used again you can make a valuable contribution towards protec-
ting our environment.
Please contact your local authorities for the location of the nearest
recycling collection point.
8
BED_AN_Multymedia_TS1 2Q4eng 29.03.2006 10:41 Uhr Seite 8

Please ensure that spent batteries removed from the remote con-
trol are not disposed of in your regular household refuse, but are
correctly disposed either in special bins for problem waste, or at
collection points in the retail trade.
Safety notes
For your own protection you should read the safety notes careful-
ly before proceeding to operate your new receiver.
The manufacturer accepts no liability for damage caused by
careless and irresponsbile handling, or by non-compliance with
the safety notes.
> To ensure adequate ventilation, place the receiver on a
smooth, horizontal surface and do not place any objects
on top of the receiver, as ventilation slots are located here
to allow heat to be dissipated from the interior of the unit.
> Do not place any burning objects, such as burning cand-
les, on top of the receiver.
> Do not subject the receiver to water droplets or water
spray, and do not place any obkects filled with liquid, such
as vases, on top of the receiver.
> Operate the receiver only in a temperate climate.
> Do not open the reciever housing under any circumstan-
ces! You are in danger of receiving an electrical shock. If it
is necessary to effect repairs in the receiver, these should
only be carried out by trained and qualified service person-
nel.
In the following cases you should disconnect the receiver
from the mains power, and should consult an expert:
> the mains cable or the mains plug are damaged
> the receiver was exposed to liquid, or liquid has run into
the unit
> in case of severe malfunctions
> in case of significant external damage
Operating breaks
In case of electrical storms, or in case of extended operating bre-
aks (e.g. while on holiday), the receiver should be disconnected
from the mains power supply.
9
BED_AN_Multymedia_TS1 2Q4eng 29.03.2006 10:41 Uhr Seite 9

10
4 Connecting the DVB receiver
a. Connecting the LNB with the LNB input (LNB IN) of the
DVB receiver.
b. Connection of the terrestrial antenna input with the
DVB-T antenna.
c. Scart connection of the DVB receiver with the television
set.
d. Scart connection of a video recorder with the VCR Scart
socket of the DVB receiver.
e. Connection from the audio outputs to a hi-fi system.
f. Mains power connection
VCR
a
e
f
c
d
b
BED_AN_Multymedia_TS1 2Q4eng 29.03.2006 10:41 Uhr Seite 10

The following references a b c etc.
refer to the illustration on page 10.
4.1 External unit
aUse a suitable co-axial cable to connect the LNB
input of the digital receiver with the LNB of your
external unit. Please also note Point 6 "Settings".
4.2 Antenna
bThe cable coming from the terrestrial antenna (indoor
or roof-mounted antenna) must be connected to the
Input terrestrial antenna of the receiver.
If possible, you should give preference to using a roof-
mounted antenna. Under favourable conditions, an
indoor antenna may also be sufficient. When using
an active antenna without an external feed,
the antenna feed must be switched on
(Point 6.5).
4.3 Connection to a television set
cUse the SCART cable supplied to connect the recei-
ver (SCART socket TV) with the television set
(SCART socket). If your television set is appropriately
equipped, this will be switched to AV mode automati-
cally when the digital receiver is switched on, and is
thus switched to receiver operation.
4.4 Video cassette recorder (VCR)
dConnect the video recorder to the SCART socket
VCR. In playback mode the video recorder will supply
a switching signal to the digital receiver. This allows
the video recorder signal to be fed automatically to the
TV set.
If your video recorder does not prtovide a switching
current, switch your digital receiver to the external
input AV using the EXTERN key. Press this key
again to return to normal operation.
11
BED_AN_Multymedia_TS1 2Q4eng 29.03.2006 10:41 Uhr Seite 11

4.5 Hi-fi amplifier
4.5.1 Analogue
eTo achieve the best possible sound quality, you can
connect your digital receiver to a hi-fi amplifier. To do
this, use a suitable cable to connect the cinch sockets
Audio R and Audio L of the digital receiver with an
input of your hi-fi amplifier (e.g. CD or AUX; note that
the phono input is not suitable!).
4.5.2 Digital
eIf your amplifier is equipped with a suitable electrical or
optical input, you should connect the socket AUDIO
OUT DIGITAL electrical resp. AUDIO OUT
DIGITAL optical wmwith the electrical resp. optical
input of your amplifier.
Depending on the signal provided by each individual channel,
sampling rates of 32, 44,1 and 48 kHz are available.
In addition, where broadcast, the Dolby Digital signal (AC3) is
also available.
4.6 Serial interface (RS 232)
The RS 232 interface is used in conjunction with updating the
operating software or pre-programming via a PC.
4.7 Mains power connection
The digital receiver should only be connected to the mains
power supply once you have completed making all the con-
nections with the various other components. This will avoid
possible damage to the digital receiver or other components.
fOnce you have made all the other connections, use
the mains adapter supplied to connect the receiver to
a mains power outlet 230 V/50-60 Hz.
5 Initial installation
Once you have read the safety notes, and have connected
the digital receiver as described in Chapter 4, you can now
switch on the receiver as described in Chapter 7. When swit-
ching on the receiver for the first time, the starting window of
the installation assistant AutoInstall will be displayed. The
installation assistant allows you to make the most important
settings of your digital receiver in the simplest way possible.
To make the settings in each respective step of the installa-
tion procedure, the keys on the remote control required for
this will be marked.
At each step of the installation there will be an explanation,
which settings can be made.
12
BED_AN_Multymedia_TS1 2Q4eng 29.03.2006 10:41 Uhr Seite 12

You can interrupt the initial installation by pressing the red
function key in the starting window of the installation assi-
stant. In the following steps of the installation, you can then
confirm the settings made by pressing the green function
key; you will then be taken to the next step of the installation
procedure. If you press the red function key you will be
taken to the previous step of the installation, thus giving you
an opportunity to correct errors at any time.
If the initial installation is not performed, or if it is aborted, the
receiver will commence operation with a standard pre-pro-
grammed procedure.
The initial installation process shown here ser-
ves merely as an example. The exact process of the
initial installation will depend on the settings you select.
Please therefore follow all instructions displayed on screen
carefully.
Operating language
> When starting the installation assistant, the first selec-
tion window to be displayed will be that for the
Operating language. (Fig. 5-1)
> Use the arrow keys up/down to mark the desired
operating (menu) language.
Your selection will automatically be taken over for the
setting of your preferred audio language.
> Confirm by pressing the green function key Accept.
Country setting
> Use the arrow keys to select the country in which
you are located.
The selection made here will result in the time zone
being set, and will affect the sorting of the programme
list. (Fig. 5-2)
> Confirm by pressing the green function key Accept
to accept the selection.
Selecting reception signals
> Use the arrow keys up/down to mark the line showing
the signal yource you wish to activate resp. de-activa-
te. (Fig. 5-3)
> Use the arrow keys left/right to activate (Yes)
resp. deactivate (No) the marked signal source.
> Confirm your selection by pressing the green func-
tion key.
13
(Fig. 5-1)
(Fig. 5-2)
(Fig. 5-3)
BED_AN_Multymedia_TS1 2Q4eng 29.03.2006 10:41 Uhr Seite 13

Antenna configuration (DVB-S)
If in your selection of signal sources you have selected Yes
for DVB-S signals, this installation step will allow you to
adjust the configuration of your digital receiver to that of your
satellite antenna.
If you have selected No for DVB-S, continue with the Point
Antenna confuguration (DVB-T).
> If you wish to accept the standard antenna setting,
press the green function key Accept. (Fig. 5-4)
Fahren Sie in diesem Fall mit dem Punkt Antennen-
Konfiguration (DVB-T) fort.
> If the configuration of your reception equipment does
not conform to the standard setting, press the yellow
function key Change.
Multytenne
> If the digital receiver is being operated in conjunction
with a Multytenne antenna, use the arrow keys
left/right to select on.
The switcvhing positions will be automatically adjusted
for the Multytenne.
In this case, continue with the point Accept antenna
configuration (DVB-S).
DiSEqC
> If you are using DiSEqC components in your receiving
equipment, use the arrow keys up/down to mark
the line DiSEqC and use the arrow keys
left/right to select on.
(Fig. 5-5). (Additional information on DiSEqC can be
found in Chapter 10, Technical terms).
> Then use the arrow keys in the column Satellite
to mark the switching position you would like to alloca-
te to a different satellite.
> Press OK to open the satellite list.
Position A/Option A
> Use the arrow keys up/down to mark the satellite
you are receiving with the DiSEqC setting Position
A/Option A, and confirm by pressing OK. (Fig. 5-6)
14
(Fig. 5-4)
(Fig. 5-5)
(Fig. 5-6)
BED_AN_Multymedia_TS1 2Q4eng 29.03.2006 10:41 Uhr Seite 14

Position B/Option A
> Use the arrow keys up/down to mark the satellite
you wish to receive with the DiSEqC setting Position
B/Option Aand confirm by pressing OK. (Fig. 5-7)
Position A/Option B
> Use the arrow keys up/down to mark the satellite
you wish to receive with the DiSEqC setting Position
A/Option Band confirm by pressing OK. (Fig. 5-8)
Position B/Option B
> Use the arrow keys up/down to mark the satellite
you wish to receive with the DiSEqC setting Position
B/Option Band confirm by pressing OK. (Fig. 5-9)
Accepting antenna configuration (DVB-S)
> When you have completed the settings for the switch
positions, press the red function key Back.
Check the configuration of your satellite antenna once
more.
> If you wish to accept the settings you have made,
press the green function key Accept.
Antenna configuration (DVB-T)
If in your selection of signals to be received you have selec-
ted Yes for DVB-T, follow this installation step to adjust the
DVB-T antenna in its optimum position, using the channel
spectrum. In addition, if you are using an active antenna that
is not fed with current via an external mains adapter, you can
use these instructions to switch the antenna current feed to
on.
> Use the arrow keys up/ down to mark the line
Antenna feed.
> Use the arrow keys left/right to switch the anten-
na feed on resp. off.
> Now position your DVB-T antenna so that the signal
level display shows the maximum level for the DVB-T
channels available at your location.
15
(Fig. 5-8)
(Fig. 5-9)
(Fig. 5-7)
BED_AN_Multymedia_TS1 2Q4eng 29.03.2006 10:41 Uhr Seite 15

Programme search/scan/ ISIPRO
The receiver will check whether a new ISIPRO program-
me list is available for downloading. If a new programme list
is available, this can be installed with the aid of the ISIPRO
function.
> Use the arrow keys up/down to mark the line ISI-
PRO programme list update. (Fig. 5-10)
> Confirm by pressing OK.
The current progrtamme list will now be downloaded
via satellite.
Please note that the programme list update will be car-
ried out only for satellite programmes. If in your selec-
tion of signals to be received you have selected Yes
for DVB-T signals as well, the programme list update
will be immediately followed by a programme scan for
DVB-T programmes.
If no new ISIPRO programme list is available, or if you do not
wish to download this, please perform a programme scan.
> To do this, use the arrow keys up/down to mark
the field All Programmes, if you wish to scan for
free-to-air as well as encrypted programmes, or All
unencrypted programmes, if you wish to search
only for free-to-air programmes.
> Confirm by pressing OK, to start an automatic pro-
gramme scan. If appropriately activated, the receiver
will first scan DVB-S sources, followed by DVB-T sour-
ces, for programmes. This procedure may take several
minutes. Please note all messages displayed on
screen.
Software update
When you have completed making the antenna settings, the
digital receiver will check whether any new version of the soft-
ware for the receiver is available via satellite. If a new version
is available, you can perform an automatic software update.
> Press the green function key Update. (Fig. 5-11).
The new software for your receiver will now be down-
loaded.
This procedure may take a few minutes, and should
not be interrupted.
16
(Fig. 5-10)
(Fig. 5-11)
BED_AN_Multymedia_TS1 2Q4eng 29.03.2006 10:41 Uhr Seite 16

Loading SFI data
our digital receiver features an electronic programme guide
(EPG) called SFI (SiehFern Info). For the data of this electro-
nic programme guide to be displayed, you must first downlo-
ad the SFI data.
When you have completed the update of your programme
list, resp. the programme scan, your receiver will automatical-
ly download the SFI data. This procedure can take up to 30
minutes.
> If you do not wish to wait for the SFI data to be down-
loaded, you can skip this procedure. To do this, press
the yellow function key Skip. (Fig. 5-12)
The SFI data will then be automatically updated the
following night, or you can update them manually at
any time (see Point 7.15.1).
Ending the installation assistant
> Confirm the final message of the installation assistant
by pressing the green function key Finish, to return
to normal operation. (Fig. 5-13)
6 Settings
Now that you have connected your new digital receiver, and
commenced operating it, you can, if you wish, proceed to
optimise its functions for your preferences.
6.1 Operating language
This menu item gives you the opportunity of setting the lang-
uage used in all the menues according to your preference.
To change the operating language proceed as follows:
> Use the Menu key to call up the Main menu.
(Fig. 6-1)
> Now use the arrow keys up/down to mark the
menu line Operating language.
> Confirm by pressing OK.
The sub-menu Operating language will be
displayed.
> Use the arrow keys up/down to mark the desired
language.
> Confirm your selection by pressing OK.
> Press the Back key to return to the Main Menu
without making any changes.
17
(Fig. 6-1)
(Fig. 5-12)
(Fig. 5-13)
BED_AN_Multymedia_TS1 2Q4eng 29.03.2006 10:41 Uhr Seite 17

6.2 Basic settings
To make the optimum use of your DVB receiver, you can still
make a number of settings in line with your personal prefe-
rences.
> Press the Menu key to call up the Main Menu.
> Use the arrow keys up/down to mark the line
Settings.
> Confirm by pressing OK.
The sub-menu Settings will be displayed.
(Fig. 6-2)
> Use the arrow keys up/down to mark the line
Basic settings.
> Confirm by pressing OK. The menu Basic settings
will be displayed. (Fig. 6-3)
> Use the arrow keys up/down to move the marker
within the menu, and to change the individual items as
indicated. When selecting a menu item, please also
note any messages displayed on screen.
The following settings can be made:
6.2.1 Time difference to GMT (hours)
Your receiver is equipped with a clock. This is synchronised
to Greenwich Mean Time via satellite.
If under Country (Point 6.2.2) you have selected the setting
None, you must simply correct the time accordingly relative
to your local time, using the arrow keys left/right. For
Germany, this difference is +1 hour, and + 2 hours in summer.
6.2.2 Country
This function allows the adjustments for the difference to
GMT, as well as the change-over from standard to daylight
savings (summer) time to be made automatically.
> Use the arrow keys left/right to enter your country
(location) in the line Country.
6.2.3 Remote control code
You can use the remote control unit of your receiver to opera-
te as many as four different appliances all using the same
remote control code. If two receivers are operated in the
same room, this may lead to accidental malfunctions. To
avoid these malfunctions, you should set different remote
control options for the two receivers.
> In this line, press the SAT1 resp. the SAT2 key as
well as the OK key simultaneously.
The remote control code of the receiver has now been
changed.
18
(Fig. 6-3)
(Fig. 6-2)
BED_AN_Multymedia_TS1 2Q4eng 29.03.2006 10:41 Uhr Seite 18

> If you wish to change the remote control from one
receiver to the other while in operation, again press
the SAT1 rssp. the SAT2 key and the OK key simul-
taneously,
6.2.4 Stand-by clock
In this line you can decide whether the current time is to be
shown in the display while the receiver is in stand-by mode.
> In this line, use the arrow keys left/right to set
the mode of the stand-by clock to on or off.
Accept settings
To accept and store the settings made in this menu, proceed
as follows:
> Press the green function key Accept. The changes
made will be saved, and you will be returned to the
menu Settings.
alternatively:
> Press the red function key Back.
A query message will now be displayed (Fig. 6-4).
> Use the arrow keys left/right to mark the field
Yes, if you wish to accept the changes made, and
confirm by pressing OK.
You will now return to the previous menu.
> Press the TV/Radio key to return to normal opera-
ting mode. The settings will not be saved.
6.3 Audio/Video settings
To optimise the digital receiver for use with your television
set, you can make further settings in the menu
Audio/Video settings.
> Press the Menu key to call up the Main menu.
> Use the arrow keys up/down to mark the line
Settings.
> Confirm by pressing OK.
The sub-menu Settings will be displayed.
(Fig. 6-5)
> Now use the arrow keys up/down to mark the line
Audio/Video settings.
> Confirm by pressing OK.
The menu Audio/Video settings will be displayed.
(Fig. 6-6)
> Use the arrow keys up/down to move the marker
within the menu, and to change the individual settings
as indicated.
19
(Fig. 6-4)
(Fig. 6-5)
(Fig. 6-6)
BED_AN_Multymedia_TS1 2Q4eng 29.03.2006 10:41 Uhr Seite 19

When selecting a menu item, please also note any
messages displayed on screen. The following settings
can be made:
6.3.1 Picture format
> Use the arrow keys left/right to set the picture for-
mat of your TV set appropriately, to 4:3 or 16:9.
This function automatically adjusts the picture format
to that of your television set.
6.3.2 Language (Audio signal)
> In this line, use the arrow keys left/right to select
your preferred language.
Where an appropriate signal is broadcast, this function
will, after a scan, automatically set this language.
6.3.3 Language (sub-titles)
Your DVB receiver is able to display sub-titles. If the function
Sub-titles is switched on, and the language selected is
being broadcast, these will be displayed automatically.
> In this line, use the arrow keys left/right to select
your sub-title language.
If the function is not activated, sub-titles can also be switched
on manually. The availability of sub-titles is indicated by
display of the message Select sub-titles. Please also note
Point 7.13 of the operating manual.
6.3.4 TV SCART mode
> In this line, use the arrow keys left/right to set the
parameter appropriate to your TV set, to the options
FBAS, RGB or S-Video. For standard sets use the
setting FBAS.
6.3.5 VCR SCART mode
> Use the arrow keys left/right to set this line in
accordance with the output signal of your VCR, to the
options FBAS, RGB or S-Video.
> For standard recorders use the setting FBAS.
20
BED_AN_Multymedia_TS1 2Q4eng 29.03.2006 10:41 Uhr Seite 20