Tecnospiro 3arm 2 Series Parts list manual

INSTRUCTIONS OPERATING
SERIES 2
ARM Nº
CONFIGURATION
WEIGHT RANGE
YEAR OF MANUFACTURE
Polígon Industrial Pla dels Vinyats, B
08250 Sant Joan de Vilatorrada (Barcelona) SPAIN
[phone] / 93 8764359
¬[phone] / 93 8764044
e-mail: [e-mail]
http: // www.3arm.net

CONTENTS
Series 2 2
Introduction 3
Safety information 4
Description 6
Arm and headmember selection 7
Operation 9
Maintenance 10
Spare parts 11
Exploded View and Parts list 12
SUPPORT Accessories 21
Notes 24
Certificate “CE” of Conformance 25

INTRODUCTION
Series 2 3
Dear customer,
We would like to congratulate you on your purchase and thank you for enabling us to
continue in our work of offering our customers an easy, reliable and versatile way of doing
any kind of manufacturing tasks.
We hope these easy instructions help you in operating and using your chosen device.
Please pay close attention to the installation and maintenance instructions detailed in
these pages.
We hope you use your device for many years and come to view your purchase of this
3ARM as an excellent investment.

SAFETY INSTRUCTIONS
Series 2 4
This operating manual contains very important information for everybody involved in the
safety during the installation, setting in operation and maintenance of this product. Despite
you feel known with similar products you must read this manual before working with the
equipment.
DANGER
Danger. Used to
indicate the
presence of a
danger that
causes severe
damages, the
death or important
material damages
if you ignore the
warning.
WARNING
NOTICE
Warning. Used to
indicate the
presence of a
danger that can
cause severe
damages, the
death or important
material damages
if you ignore the
warning.
CAUTION
Caution.Used to
indicate the
presence of a
danger that
causes or can
cause severe
personal or
material damages
if the warning is
ignored.
Notice. Used to
inform important
information for the
installations,
setting in operation
or maintenance,
but it is not related
with dangers.
Not leave the arm floating when it is not used. Fix the tilting arm together the radial arm by
means the fixation clip.
You must use the protection equipment according the manufacturer instructions of the tool
fixed in the arm.
•Operators must keep out of the vertical route of the arm.
•Do not exceed the weight limits marked in the arm and the main page of this
manual.
•In case of change of the load, loose the damper (see page 9). Please, bear the
possible going up movement in mind when you take out the load.
•Do not put your hand in the area below the lifter sheath when repositioning this in its
lowest positions.
•Do not put your fingers in the upper part of the cross unit or in the lower part of the
headmember when the arm is nearing its most raised position.
•Do not put your fingers in the lower part of the cross unit or in the upper part of the
headmember when the arm is nearing its lowest position.
•To make sure the tool is totally fixed before starting to work.
CAUTION

SAFETY INSTRUCTIONS
Series 2
5
The elevator equipments are subjected to different rules in each country. These
regulations could not be described in this instructions manual.
Operators working closer to the suspension weight or with an arm with tooling must keep
out of its vertical route. From the safety point view, all operations must be done without
any damage if the equipment fails.
The owner or user has the responsibility to decide the suitable use of the product. We
recommend the checking of the current rules in each sector, activity, country, etc.
Read the instructions before using it.
It is very important to familiarize the operators with the right use of these products or
similar and be able to work with them. They must have basic knowledge of:
•To work with common manual tools.
•Safety procedure, cautions and habits of safe jobs.
Tecnospiro Machine Tool does not know the procedures and applications that the
customer can apply to the arm, and damages and/or results of them. If you make working
operations or maintenance not described for the manufacturer, be sure that you are not in
danger. If you have any doubt or query, please do not hesitate to contact with the
authorized supplier. .
WARNING

DESCRIPTION
Series 2 6
1.- Base 2.- Radial arm
3.- Cross unit 4.- Tilting arm
5.- Headmember
The machine consists of a pendular parallelogram that is balanced by a pneumatic spring,
plus a radial arm. The gas spring and radial arm assembly fixes the motor head (6 options)
and keeps it perpendicular to the working area.
WORKING AREA

ARM and HEADMEMBER SELECTION
Series2 7
METRIC / KG

OARM and HEADMEMBER SELECTION
8
Arm VERTICAL headmember ARTICULATED headmember
B / BE
Vertical
A2 Flat B2 Adjustable C2 Articulated D2 Flat E2 Adjustable F2
BE: Radial arm with
regulating base
INCHES / LB.

OARM and HEADMEMBER SELECTION
INSTALLATION
1. Attach the machine base plate to the work table by means of three M8 screws or a
clamp.
2. Fit the radial arm into the base axis, tighten the 2 Allen M5 and cover them with the
two plastic caps.
WORK WITH HIGH PIECES
Hold the base casing, pull it up and turn it 90º to fix it. The machine will be 130 mm higher,
and now it is ready to work.
ARM BALANCE
Regulating the internal strain damper different weights at the arm end are balanced.
•Using an ALLEN key of 5mm, take up or let down the thread regulating shank (1)
located in the lower part of the cross unit.
oDown (turn left): More strain to the damper.
oUp (turn right): Less strain to the damper.

MAINTENANCE
The arm DOES NOT need maintenance and it is difficult to have anomalies if you make a
correct use of it, although we specify the main and easy repairs that you can do.
DAMPER REPLACEMENT
1. Let down the damper regulating assembly (1), located below the cross unit.
2. Take out the headmember (2).
2.1.Remove the screws that hold the headmember to the arm
2.2.Use the screw M5 to take out the stay spindle (figure 2). For doing this operation,
the arm must be located in its lowest position. Then, loosen the screw rod (located
below the headmember) that fixes the stay spindle.
3. Take out the spindle of the arm damper (4).
4. Take up the damper regulating assembly.
5. Take out the damper (5).
6. Reverse the process for the reassembling.
Figure 1
Figure 2

SPARE PARTS
Base: 20105004
Base casing: 201025A3
Radial arm: 20105104
Tilting arm: 20101503
Cross unit: MV200104
Damper: MVL_ _ _ 04
(according weight)
Thread regulation bushing : 20B103A3
Thread regulation shank: 20B102A3
Headmember
VERTICAL 201055A4
Headmember
Vertical FLAT : 20105604
Headmember
Vertical ADJUSTABLE:
MV200204
Headmember
ARTICULATED: MV200504
Headmember
Articulated FLAT:
MV201104
Headmember
Articulated ADJUSTABLE:
MV201304
Spindle of the arm damper:
20101803
Spindle arm with screws:
20105304
Stay: 20105404
Stay spindle: CL020116

EXPLODED VIEW

EXPLODED VIEW
Series 2
13
No. Qty. Ref. DESCRIPTION
1 1 20101103 Base
2 1 201012A3 Radial arm
3 1 301035A3 CE label
4 2 AC090586 Rivet DIN 7337 - Ø4
5 2 CO080906 Axial disc AS2035 - 20 x 35 x 1
7 1 20101503 Tilting arm
8 1 FA030366 Washer DIN 125 - A Ø6
10 4 CA011436 Screw DIN 912 - M6 x 16
11 4 AC040376 Cap 0390006
14 1 201025B7 Base casing
16 3 AC040426 Cap R26-D16
17 2 AC040136 Cap R26-D30
21 1 20101803 Spindle damper
22 1 20B10703 Cross pin
23 4 CA030356 Stud DIN 913 - M5 x 10
24 1 20101603 Stay
25 1 CO070326 Selfoil bushing 20-25-20
26 1 CO070316 Selfoil bushing 20-25-25
27 1 201021A3 Base spindle
28 1 CO061046 Elastic ring WR20
29 3 CA011256 Screw DIN 912 - M5 x 8
30 4 CO011076 Bearing HK2016 - 20 x 26 x 16
33 2 CO011056 Bearing - HK0810 - 8 x 12 x 10
34 1 CL020116 Pin DIN 7979 D8x28
35 1 AC090476 Fixation clip M6
36 1 FA010286 Nut DIN 934 - M6
39 1 MVL_ _ _ 04 Damper (indicate the weight to support in the 3 central digits)
40 2 20101703 Spindle arm
41 1 MV200104 Cross unit
41.1 1 20B10103 Cross
41.2 1 201020A3 Spindle cross
41.3 2 CO011066 Ball bearing HK1012 - 10 x 14 x 12
43 1 20B103A3 Thread regulating bushing
44 1 20B102A3 Thread regulating shank

EXPLODED VIEW
Series 2
14

EXPLODED VIEW
Series 2
15
No. Qty. REF. DESCRIPTION
1 1 25101303 Base
2 1 CL030103 Elevator spindle
3 1 FA030406 Washer DIN 9021 - Ø12
4 1 FA030196 Washer DIN 125 - Ø8
5 1 CA010106 Screw DIN 912 - M8 x 25
7 2 AC060446 Handle ERX63pM6x40-C5
8 1 CA031546 Stud DIN 914 - M20 x 40
9 1 CL030503 Radial arm
10 1 AC040506 Abutment 049160011407
11 2 CO130056 Cup PAP3020P20
12 1 CL030203 Locking ring
13 2 CL030303 Locking bushing
14 3 AC040426 Cap R26-D16
18 1 AC040136 Cap R26-D30
19 1 CO080906 Axial disc AS2035 - 20 x 35 x 1
25 2 CO011076 Bearing HK2016 - 20 x 26 x 16
26 1 FA030296 Washer DIN 125 - Ø5
27 1 CA011256 Screw DIN 912 - M5 x 8
28 2 20101703 Spindle arm
29 1 20101503 Tilting arm
30 4 CA011436 Screw DIN 912 - M6 x 16
31 4 AC040376 Cap 0390006
32 1 20101803 Spindle of the arm damper
33 1 20101603 Stay
34 2 CO011056 Bearing HK0810 - 8 x 12 x 10
39 2 CA031076 Stud DIN 913 - M5 x 8
40 1 MVL_ _ _ 04 Damper (indicate the weight in the 3 central digits)
41 1 20B10703 Cross pin
46 1 MV200104 Cross unit
46.1 1 20B10103 Cross
46.2 1 201020A3 Spindle cross
46.3 2 CO011066 Bearing HK1012 - 10 x 14 x 12
47 1 20B103A3 Thread regulating bushing
48 1 20B102A3 Thread regulating shank
49 2 CA030356 Stud DIN 913 - M5 x 10

EXPLODED VIEW
Series 2
16
No. Qty. REF. DESCRIPTION
1 1 201014A3 Vertical headmember
2 2 CO011066 Bearing HK1012 – 10x14x12
3 1 CA010716 Screw DIN 912 – M8x35
No. Qty. REF. DESCRIPTION
1 1 20B11103 Flat headmember
2 2 CO011066 Bearing HK1012 – 10x14x12
A2
VERTICAL
head
B2
Vertical FLAT
head

EXPLODED VIEW
Series 2
17
No. Qty. REF. DESCRIPTION
1 1 20B11103 Flat headmember
2 4 CA01066 Screw DIN 912 – M6x30
3 4 CA011966 Screw DIN 931-1 M6x60
4 1 MV200303 Adjustable headmember base
5 1 MV200403 Adjustable headmember clamp
6 2 CO011066 Bearing HK1012 – 10x14x12
C2
Vertical ADJUSTABLE
hea
d

EXPLODED VIEW
Series 2
18
No. Qty.. REF. DESCRIPTION
1 1 CO110486 Bushing Ensat M10x14x10 30710016
4 2 CA010616 Screw DIN 912 - M5 x 25
5 1 CA031536 Stud DIN 913 - M5 x 16
6 1 CA031026 Stud DIN 913 - M8 x 10
7 2 CO011066 Bearing HK1012 - 10 x 14 x 12
8 1 AC060456 Handle ERX78pM8x40-C5 Blue
9 1 MV200603 Pivot
10 1 CA031596 Stud DIN 915 - M8 x 20
11 1 203B10A3 Fork headmember
12 1 MV200704 Tilting base with brake discs (“ferodos”)
12.1 2 MV200803 Brake disc “ferodo”
12.2 1 MV200903 Tilting base
13 1 MV201003 Motor support
15 1 MV201003 Handle ERZ78pM10x40
16 2 DC006503 Axial disc
17 1 MV201703 Handle rod
18 1 AC060566 Handle ERX78bM8-C5
19 2 CO081196 Axial disc SS 8x14x1.2
D2
Articulating
VERTICAL
head

EXPLODED VIEW
Series 2
19
No. Qty. REF. DESCRIPTION
1 1 CO110486 Bushing Ensat M10x14x10 30710016
5 1 CA031536 Stud DIN 913 - M5 x 16
6 1 CA031026 Stud DIN 913 - M8 x 10
7 2 CO011066 Bearing HK1012 - 10 x 14 x 12
9 1 203B10A3 Fork headmember
10 1 MV200704 Tilting base with brake discs “ferodos”
10.1 2 MV200803 Brake disc “ferodo”
10.2 1 MV200903 Tilting base
12 1 MV201203 Flat support
13 1 CA031596 Stud DIN 915 - M8 x 20
14 1 MV200603 Pivot
15 1 AC060503 Handle ERZ78pM10x40
16 2 DC006503 Axial disc
17 1 AC060566 Handle ERX78bM8-C5
18 1 Mv201703 Handle rod
19 2 CO081196 Axial disc SS 8x14x1.2
E2
Articulating FLAT
head

EXPLODED VIEW
Series 2
20
No. Qty. REF. DESCRIPTION
1 1 CO110486 Bushing Ensat M10x14x10 30710016
4 1 CA031536 Stud DIN 913 - M5 x 16
5 1 CA031026 Stud DIN 913 - M8 x 10
6 2 CO011066 Bearing HK1012 - 10 x 14 x 12
9 4 CA010666 Screw DIN 912 - M6 x 30
10 4 CA011966 Screw DIN 931-1 - M6 x 60
11 1 MV200303 Adjustable head base
12 1 MV200403 Adjustable head clamp
13 1 203B10A3 Fork head
14 1 MV200704 Tilting base with brake discs “ferodo”
14.1 2 MV200803 Brake disc “ferodo”
14.2 1 MV200903 Tilting base
15 1 MV201203 Motor flat support
16 1 CA031596 Stud DIN 915 - M8 x 20
17 1 MV200603 Pivot
18 2 DC006503 Axial disc
19 1 AC060546 Handle ERZ78pM10x40
20 1 AC060566 Handle ERX78bM8-C5
21 1 MV201703 Handle rod
22 2 CO081196 Axial disc SS 8x14x1.2
F2
Articulating ADJUSTABLE
head