Tee-Zed dreambaby Royale Converta 3-in-1 Play-Pen... User manual

IMPORTANT!·READ AND FOLLOW THESE INSTRUCTIONS CAREFULLY
AND KEEP FOR FUTURE REFERENCE
Read the entire instructions before assembling and inst{llling this product.
If you sell or give away this product, make sure you give this-instruction to the new owner.
Complies with Standards: EN 12227:2010.
A WARNING
• Suitable for children up to 24 months.
• Ensure that the Play-Pen is fully erected and all the locking
rnechanisrns engaged before placing your child in this Play-Pen.
• Do not place the Play-Pen close to an open fire or other heat
source. Ensure the Fireplace Barrier is installed at least
60cm/23.5in from fire source.
• This product does not replace adult supervision.
Never leave a child unattended.
• Never use with a child able to climb over or dislodge/open the
Play-Pen/Fireplace Barrier/Wide Barrier Gate.
• Do not leave anything in the playpen which may provide a
foothold for climbing.
• The safety barrier is for domestic use only.
• The gate panel has a manual close system.
• The safety barrier must not be fitted across windows,
• Do not use if any components are missing or damaged.
• This Play-pen is not intended for sleep u~e.
COMPONENTS
A GATE PANEL
B BARRIER PANEL
C UPPER SECURING HINGE
D SECURING SCREW
E LOWER HINGE
F VERTICAL BAR
G VERTICAL BAR TOP CASING
H GATE RELEASE SWITCH
GATE UPPER LOCK
J GATE LOWER LOCK
WALL MOUNTING PARTS
K UPPER MOUNT I Side XI
L UPPER MOUNT I Side Y I
M LOWER MOUNTS
N SCREWS [38mm/ 1.5in!
o LOWER HINGE CAP
P FLOOR CAP
REQUIRED FOR
ASSEMBLY!MOUNTING
Q ALLEN KEY [4mm!
NOTE: Store Allen Key safely
out of reach of children.
Keep for future use .
. 11\ WARNING: This package contains small parts and
~ sharp points in an unassembled state. Keep out
of reach of children. Adult assembly required.
~D
Q~1
F

PLAY-PEN ASSEMBLY @
Remove Play-Pen from packaging and place upright on flat surface.
2 Position panels to desired shape.
3 The vertical bars (F) at each end of the Play-Pen must first be removed.
Note- For Play-Pen assembly only one of these vertical bars are required.
The other vertical bar is only used when wall mounting as a barrier gate or fire barrier, store for future
use. For shipping purposes one of these vertical bars is temporarily secured at the lower hinge (E) with a
securing screw (0).
• Use Allen Key (Q) to remove securing screw (D) from upper securing hinge (Cl, and lower hinge [E).
Keep screws for future use. Keep out of reach of children.
• Release the vertical bars [F) from the upper securing hinge (C) by pulling down on the top casing [G).
• Twist to release and remove vertical bar [F) from lower hinge [E).
4 Join panels by connecting upper securing hinge (C) and lower hinge [E).
_5 Install vertical bar [F).
•.Insert vertical bar into lower hinge [E). Twist to lock into place.
~ Pull down top casing (G) and insert into upper securing hinge [C).
• Insert securing screw [D) and position in place with Allen Key [Q)'
6 Position Play-Pen into desired shape, then lock
and secure by firmly tightening all securing
screws (D) using Allen Key [Q)'
Assembled
Play-Pen
Play-Mats available
(sold separately)
F962/F2006

BARRIER GATE OR FIREPLACE BARRIER INSTALLATION ®
CAUTION: Ensure fireplace barrier is installed at least 60cm/23.5in from fire source.
Ensure the surface you mounting the barrier is structurally sound such as solid timber, brick or masonry.
For plaster/gyprock surface, locate the timber beam or stud behind and mount in this location [mounting on
plaster/gyprock alone. is not strong enough and not safe!' Do not mount to glass.
Follow steps 1-3 of Play-Pen assembly.
2 Locate best position for barrier gate/fireplace barrier to be installed.
Position panels 1od·~sire~d shape plactAg end panels close to the wall.
3 Cut out templates and position on wall.
Note- The 2 ends of the barrier gate/fireplace barrier are different. Match the template to correct end.
4 Mark screw holes.
5 Drill holes.
6 Install wall mounts Side X and Side Y.
SIDE X SIDE Y
SIDE X
• Insert upper mount [K) and lower hinge cap [a).
• Thread lower mount [M) onto vertical bar [F).
• Install vertical bar [F) into lower hinge cap (01 and upper mount [K).
• Insert securing screw [D) and position in place with Allen Key [Q)'

SIDEY
• Thread lower mount [M] onto vertical bar [F].
• Install floor cap [P] under lower hinge [E].
• Insert upper mount [l.l onto upper securing hinge [Cl and hold in place.
• Insert vertical bar [F] into lower hinge [E] and upper mount [L],
• Insert securing screw [0] and position in place with Allen Key [Q]'
,
7 Align both sides
with template
and affix with
screws [N].
8 Position barrier gate/ fireplace barrier
into desired shape, then lock and
secure by firmly tightening all securing
screws [0] using Allen Key [Q]'
Assembled
Barrier Gate
T
GATE OPERATION
Slide the release switch [H] and lift gate panel [A].
Gate swings in both-directions,
Swing gate closed ensuring upper [I] and lower [J]locks engaged.
Swin9 gate fully open to engage SMART STAY OPEN feature.
Oaution: Keep gate closed when children are present.
V'"
r.
MAINTENANCE & CARE
• Play-Pen/Fireplace Barrier/Barrier Gate must be fitted according to instructions to ensure it works correctly.
• Regularly check all pails to ensure Play-PeoLFireplace Barrier/Wide Barrier Gate is secure. Adjust as required.
• Only use Dreambab? spare parts.
• To clean, wipe surface with a damp cloth using mild detergent and warm water.
Never clean with abrasive, ammonia, bleach or spirit based type cleaner.
Look for the Dreambabfl range of Child Safety and Care Products.
Tee-Zed ackn~ tiat its customers may be entitled to statutory consumer guarantees and does not seek to exclude or limit them. These guarantees include that Tee-Zed's products are of acceptable quality. This Tee-Zed product is for
the specific pUrpc2~hdin the instructions and packaging and Tee-Zed considers use outside of that purpose to be abnormal use. To the maximum extent permitted hylaw, Tee-Zed does not accept any liability for damage:
• arising from a~::cn:::algse of the products;
• caused by insbtwi; er nmovaL of the products other than in accordance with the supplied installation and removaL instructions; or
• arising under the tzwof tert or contract.
Dreambabye products by
~~
Tee-Zed Products Pty Ltd
PO Box 2022
Bondi Junction NSW 1355
Australia
Tel:+61 [01293864000
[email protected]
www.dreambaby.com.au
Tee-Zed Products [N.Z.I Ltd
PO Box 64013
Botany Town Centre Auckland
New Zealand
Tel: +64 [019 2748788
[email protected]
www.dreambaby.co.nz
(,.,{Cl.qe
Made in Zhejiang, China. ~ (J;i<;.-
©2016 Tee-Zed Products Pty Lld <.6<:9
drea mba bysafety
You. lii4I"I®M
Tee-Zed Products Ltd
PO Box 29227
Dunfermline, KY122DN
United Kingdom
Tel: +44[018448009445
[email protected]
www.dreambaby.co.uk