Teka Intra Endura ED2DF User manual

POLISHED
Art. no.
GTIN
ED2DF
7055570014226
Overall dimension in mm 331 x 338 x 236
Depth in mm 106
Material AISI 304
Material thickness in mm 1,25
Installation height in mm 900 / 700 / 500
Product load in N 1000
Gross weight in kg 4.50
Weight pallet 106.00
Pcs per pallet 18
Made in Norway
Description
Vandal r sistant drinking fountain in stainl ss st l
18/10, for wall mounting. With clos d shroud for
conc al d in- and outl t. Suppli d with int grat d
wast , wat r trap wat r bubbl r.
Installation
Fast n th top and bottom brack t to th wall
according to th nclos d drill t mplat . Fix th
bubl r and conn ct to wat r. Conn ct th wat r trap
to th outl t in th wall with a 32mm push fit tub
(Not suppli d). Fix th drinking fountain onto th top
fixing brack t and lock it with th 2 h adl ss scr ws to
th bottom fixing to s cur th fountain to th wall.
Drink. fountain ED2DF
FDV Revision 20151215www.intra-teka.com

Installation ED2DF
ASSEMBLY / SPARE PARTS:
Included in the box + spare part nu bers:
* Fountain hole
* Drink nozzle fitting: 79090
* Male thread R1/2” -R3/8": 78099
* Flexible hose 1/2” x 1/2" elbow: 82033
* Fibre gasket Ø19: 79098
* Valve 1 1/4” botto section: 79004
* Gasket, Celleprene Ø70: 91093
* Water trap 1 1/4” x 32 : 78088
* Pipe Ø32 -150 in length: 78090
* Set screw M6x25 A4: 86160
* Suspension strip: ZED2OPP
* Wall bracket: ZED2VF
* Asse bly kit: YMX01
* Asse bly instructions with te plate: 76272
Attach the te plate to the wall at the correct height
for the sink and use this to pre-drill the holes for the
suspension strip and wall bracket. Existing pipework
ust be flushed and cleaned before connecting the
drinking fountain, so that there is no dirt in the
drinking nozzle. Pipe filters which collect dirt should
be ounted in the transition between the fixed piping
and the flexible hose for water intake.
Install the suspension strip and wall bracket in
accordance with the acco panying drilling te plate.
Install drinking nozzle and connect to the water
supply. Connect the water trap to the outlet in the
wall, hang the washstand on the suspension strip and
affix it to the wall bracket with 2 set screws on the
underside of the cover.
Mounting height 900 for adults, 700 – 800
for children and 500 for young children.
The stop valve ust not be used to adjust the a ount
of water in the drinking nozzle, as this ay cause
leakage. A pressure reducing valve should reduce the
water pressure
to 3.5 bar.
ADJUSTING THE WATER JET:
The water flow through the drinking nozzle and the
path of the water jet is adjusted with the screw on the
underside of the drinking spout. This is acco plished
by pressing the shutter release while the screw is
adjusted.
The screw is very s all, so it ust be screwed very
carefully so that the screw does not co e out.
- Turn the screw clockwise and the water flow is
reduced.
- Turn the screw anti-clockwise and the water flow is
increased.
2
FDV Revision 20151215www.intra-teka.com

Maintenance ED2DF
SPARE PARTS:
(See ASSEMBLY)
TECHNICAL INFORMATION:
Drinking nozzle:
Ma . working pressure: 5.5 bar
Min. working pressure: 0.5 bar
Recommended working pressure: 3.5 bar
Connection to water:
The amount of water must not be restricted with a
shut-off valve,as this may cause leaks from the
drinking nozzle.
SERVICING IN THE EVENT OF LEAKS:
Leaks by the spout of the drinking nozzle: may be
caused by a damaged O-ring or dirt under O-ring JR2:
Clean piston P312U included in KBP311N.
Apply some grease around the piston before
assembly. If the O ringJR2 is damaged, the entire
drink nozzle should be replaced.
Leakage under the pressure button: most
likelycaused by a damaged or dirty O-ring, JR1:
Clean the piston P312U included in KBP311N.
Apply some grease around the piston before
assembly. If the O ringJR1 is damaged, the entire
drink nozzle should be replaced.
MAINTENANCE:
In order for the product to retain its original quality
and appearance, regular cleaning is recommended.
Use mild soap or products specifically designed for
stainless steel and clean water. Then wipe the surface
with a dry cloth.
Never use detergents containing chlorine, iodine,
fluoride or abrasives. Also avoid contact with acidic
solutions and other substances incompatible with
stainless steel. Remember that foodstuffs and skin
care products may contain such substances; e.g.
ketchup, juice, salt, some cleansers, nail polish, etc.
Promptly remove spills of such products.
* Do not allow water or other liquid to dry in. This is
to avoid staining the surface.
* Even though stainless steel can withstand harsh
treatment, it will easily be scratched by sharp objects.
For products with polished (brushed) finishes, this
will be very visible when the product is new, but after
a period of use, this will be negated as the steel loses
3
FDV Revision 20151215www.intra-teka.com