Teknik FS-100DT2 User manual

FS-100DT2
FS-150DT2
FS-200DT2-W
[SENTRY]
LED FLOODLIGHT
USER MANUAL
Teknik Lighting Solutions Pty Ltd
ABN: 44 608 397 913
Tel: [phone]
www.tekniklighting.com.au

INTRODUCTION
Thank you for selecting the [SENTRY] LED Floodlight. Please ensure that the luminaire is
installed in accordance with the below instructions. Teknik Lighting Solutions Pty Ltd assumes no
responsibility for inappropriate use or installation of the product, including any associated damage
caused.
PRECAUTION
1. Read the entire manual carefully
before installation and operation.
2. The Warranty Period is five (5) years.
Teknik will repair or replace the product if it
fails or becomes defective during normal
use within the prescribed warranty period.
3. Designed for industrial and
commercial use.
4. The lifetime of the product is aected
when it is used in a fully enclosed fixture.
5. Installation must be performed by a
licenced and qualified electrician.
6. Use solid copper wire of 18 AWG
(minimum) for the input terminal
extension, and 20 AWG (minimum)
for the output terminal extension.
7. Do not change or tamper with any
internal electric circuits or wiring,
connectors or cables for any reasons.
8. Do not insert foreign objects into the
product. This may result in electric shock,
malfunction or damage to the products.
9. When in operation the luminaire
temperature may reach up to 60°C.
10. Teknik accepts no liability for any injuries
or damages resulting from the incorrect
use of the lamp or use of the lamp in
combination with inappropriate equipment.
11. Luminaire is non-dimmable.
12. For further information, please
contact Teknik Lighting Solutions
or your local distributor.
13. This product has no user serviceable
parts. If any part is damaged, disconnect
from mains and discontinue use.
14. Warning: Luminaire marked as NON-
IC according to ASNZS60598-2.2. Not
suitable for use on residential properties.
DO NOT COVER OR ABUT. Any insulation
material must be positioned at a minimum
distance of 100 mm from the fitting.
15. Do not cover the light.
16. The warranty shall exclude modifications
to the product, incorrect installation and
use outside of the intended scope.
SPECIFICATIONS
Input Voltage 90-305 VAC ~ 50/60Hz
Power 100W 150W 200W-100W
Lumen Output 13000lm 19500lm 26000lm-13000lm
Colour Temp 5000K
CRI >70
Beam Angle Asymmetric T2
Connection Flex and plug (1.2m)
Net Weight 2.7kg 3.2kg 3.8kg
Lifetime ≥50,000 hours
IP Rating IP65
Dimensions 285(L) x 50(W) x 302(H) 285(L) x 50(W) x 352(H) 285(L) x 50(W) x 415(H)
2

3
Locate the Wattage Switch box as per the dimensional drawing below. To access the
switches, use a large screwdriver or coin to open the box.
120W
1 2 3 4
200W
1 2 3 4
150W
1 2 3 4
OFF
ON
180W
1 2 3 4
100W
1 2 3 4
Wattage
Switch Box
INSTALLATION
Fix M8 screws
to mounting
position. Loosen screws,
adjust the bracket
to appropriate
angle and then lock
screws.
WATTAGE SWITCHABLE FUNCTION: FS-200DT2-W ONLY
DIMENSIONAL DRAWINGS
200W-100W
285mm
415mm
50mm
150W
285mm
352mm
50mm
100W
285mm
302mm
50mm

5/26-34 Dunning Ave, Rosebery NSW 2018 | 1300 313 780 | [email protected]
www.tekniklighting.com.au
DISCLAIMERS
1. This product must be installed and used as per these instructions.
2. This product contains no serviceable parts and no attempt should be made to repair this product. If the
product is faulty it should be discarded.
3. This product is not suitable for installation in hazardous and/or corrosive areas.
4. Electrical installations periodically receive transient over voltages. This product has been designed to
minimise the eect of such voltages on connected equipment. It may not give full protection for extreme
over-voltage transients such as those resulting from a close lightning strike.
5. This product utilises intellectual property in the form of registered designs, trademarks, and/or patents.
Such intellectual property remains the property of Teknik Lighting Solutions Pty Ltd in all cases.
6. This product has been designed to operate in ambient temperatures -20oC to + 40oC.
Terminal block is not included. To ensure that the product meets the protection level requirements,
the luminaire must be connected to terminal block with IP66 degree or above.
The terminal block shall be conformed to IEC/EN 60998-2-1 or IEC/EN 60998-2-2 and have the
following specifications:
- Screw terminal block with 3 holes
- Suitable for 1.0-2.5 mm2wire
Installation must be performed by a qualified person:
- Brown wire must be connected to L pole
- Blue wire must be connected N pole
- Yellow green wire must be connected earth pole
WIRING DIAGRAM
4