Tektronix RMD5000 User manual

RMD5000
Rackmount Kit
ZZZ
Instructions
xx
www.tektronix.com
*P075102000*
075-1020-00

Copyright © Tektronix. All rights reserved. Licensed software products are owned by Tektronix or its subsidiaries
or suppliers, and are protected by national copyright laws and international treaty provisions.
Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication
supersedes that in all previously published material. Specifications and price change privileges reserved.
TEKTRONIX and TEK are registered trademarks of Tektronix, Inc.
Contacting Tektronix
Tektronix, Inc.
14150 SW Karl Braun Drive
P.O. Box 500
Beaverton, OR 97077
USA
For product information, sales, service, and technical support:
In North America, call 1-800-833-9200.
Worldwide, visit www.tektronix.com to find contacts in your area.

Service Safety Summary
Only qualified personnel should perform service procedures. Read this Service
Safety Summary and the General Safety Summary in the product service manual
or the instruction manual.
Do Not Service Alone. Do not perform internal service or adjustments of this
product unless another person capable of rendering first aid and resuscitation is
present.
To prevent the instrument and rack from falling onto the operator, two or more
installers should install the instrument into the rack cabinet. After completing the
installation procedure, the installers should verify that the instrument and rack
cabinet will not tip forward while the instrument is in the extended position.
Disconnect Power. To avoid electric shock, switch off the instrument power, then
disconnect the power cord from the mains power.
UseCareWhenServicingWithPowerOn. Dangerousvoltagesorcurrentsmay
exist in this product. Disconnect power and disconnect test leads before removing
protective panels, soldering, or replacing components.
To avoid electric shock, do not touch exposed connections.
RMD5000 Rackmount Kit Instructions 1

Kit Description
Kit Description
These instructions describe the installation of the rackmount kit to your standard
bench-top instrument. The rackmount kit is a collection of parts that, once
installed, configure the instrument for mounting in a fixed position into a standard
19-inch equipment rack. (See Table 1.) If you require the instrument to slide in
and out of the rack, order the optional slide kit. (See Table 2.)
Products
DPO4000B Series All Serial Numbers
MSO4000B Series AllSerialNumbers
DPO5000 Series AllSerialNumbers
MSO5000 Series AllSerialNumbers
Kit Parts List
The parts included in this rackmount kit are listed below. (See Table 1.) (See
Figure 1 on page 3.)
Table 1: RMD5000 Rackmount kit
Item Quantity Part number Description
1 1 each 407-5531-XX PLATE, MOUNTING; RACKMOUNT LEFT
2 1 each 407-5532-XX PLATE, MOUNTING; RACKMOUNT RIGHT
3 1 each 407-5534-XX PLATE, SUPPORT; RACKMOUNT TOP
4 1 each 407-5533-XX PLATE, SUPPORT; RACKMOUNT BOTTOM
51 each 426-2636-XX PLATE, SUPPORT; RACKMOUNT FRONT
6 1 each 016-2037-XX HARDWARE KIT
71 each 016-2038-XX COMMON HARDWARE KIT
—1 each 075-1020-XX TECH MANUAL: INSTRUCTIONS, RACKMOUNT KIT
Optional Accessories
Table 2: Optional Accessories
Part number Description
351-1095-XX SLIDE ASSY; PAIR, W/STD HARDWARE KIT AND REAR BRACKET
2 RMD5000 Rackmount Kit Instructions

Kit Description
Figure 1: Rackmount kit parts (part appearance may vary)
Figure 2: Optional slide assembly kit
RMD5000 Rackmount Kit Instructions 3

Kit Description
Warranted Characteristics
When the instrument is installed according to the instructions in this document,
the rack-mounted instrument meets all warranted characteristics listed in the
instrument specification except for those listed. (See page 5, Environmental
Requirements.) Instruments mounted using methods other than those described in
these instructions may not meet their warranted characteristics.
See the specifications for your instrument model for tables of the warranted
characteristics.
Cooling air enters on the bottom and right sides as shown. (See Figure 3.) You
must provide adequate cool air to meet the ambient temperature requirements
listed. (See Table 3 on page 5.)
Figure 3: Instrument cooling
4 RMD5000 Rackmount Kit Instructions

Kit Description
Environmental Requirements
The following environmental characteristics supersede those listed in the
specifications and performance verification sections of the manual for your
instrument.
Table 3: Warranted characteristics
Characteristic Description
Temperature
inside rack cabinet
Operating +10°Cto+45°C(+50°Fto+113°F)
Nonoperating –22 °C to +60 °C (–7.6 °F to +140 °F)
Shock
Operating and
nonoperating
20 g, 11 ms, half sine, each axis, 3 drops each
Clearance Requirements
The rack in which the rack adapted instrument is mounted must provide the
following clearance requirements:
A minimum of 8.75 in (222.25 mm) of vertical space
A minimum width of 17.72 in (450.09 mm) between the left- and right-front
rails in the rack
A minimum depth of 12.75 in (323.85 mm)
CAUTION. Adhering to these clearance requirements provides the rack-mounted
instrument with sufficient clearance for air circulation and accommodation of the
power cord and mounting hardware. Failure to provide these clearances can
result in overheating and can cause instrument faults or failure.
RMD5000 Rackmount Kit Instructions 5

Kit Description
Figure 4: Instrument with rack adapter installed
6 RMD5000 Rackmount Kit Instructions

Installation Instructions
Installation Instructions
This section contains the procedures needed to rackmount a DPO4000B,
MSO4000B, DPO5000, or MSO5000 series instrument.
Minimum Tool and Equipment List
The following tools are required to attach the rack-adapter kit hardware, install
cabling hardware, and mount the rack-adapted instrument into a standard
equipment cabinet. All tools are standard tools that are readily available.
Table 4: Tools required for rackmount installation
Name Description
Screwdriver handle
(magnetic)
Accepts 1/4-inch hexagonal head driver tips
No. 2 Phillips or
PoziDriv tip
Phillips or PoziDriv-driver tip for number 2 size screw heads
T-10 TORX tip TORX-drive tip for T-10 size screw heads (flat-head)
T-15 TORX tip TORX-drive tip for T-15 size screw heads
T-20 TORX tip TORX-drive tip for T-20 size screw heads
1/4-inch wrench Wrench or nut driver can be used to install slides
Torque driver 6.5 in long shaft; accepts 1/4-inch hexagonal head driver tips
These instructions are for qualified service personnel who are familiar with
servicing the product. If you need further details for disassembling or reassembling
the product, refer to the appropriate product manual. Contact your nearest
Tektronix Service Center or Tektronix Factory Service for installation assistance.
WARNING. To prevent the rackmounted instrument from tipping forward onto the
operator, install the instrument so that the operator will be able to access all of its
rear-panel connectors without pushing down on the instrument.
Verify that the rack does not become unstable with the instrument fully extended.
Do not leave the instrument extended when finished accessing the rear panel.
WARNING. To avoid electric shock, disconnect the power cord from the mains
power before removing the cover. Failure to do so could result in personal injury
or death.
RMD5000 Rackmount Kit Instructions 7

Installation Instructions
Remove
Equipment Required: Screwdriver handle with T-15 tip.
This procedure prepares the instrument for installation of the rackmount parts.
NOTE. Retain all parts removed from the instrument for later use. Some of those
parts will be reinstalled as you perform this rack conversion; store the remainder
in case reconversion to a standard instrument configuration is desired at a later
time.
1. Disconnect the power cord from the rear of the instrument.
2. Remove the four T-15 TORX screws that secure the rear cover to the front
case assembly. (See Figure 5.)
3. Remove the rear cover.
Figure 5: Removing the rear case cover
8 RMD5000 Rackmount Kit Instructions