Telecom FM OneStream GBRI User manual

1
OneStream GBRI Quick Start Guide
Version 1
This guide gives a basic overview of installing and programming the OneStream GBRI to route calls
between PBX Trunk (S0) ports and GSM. For more information please refer to the OneStream
Hardware Installation Guide and OneStream Programming Guide which are both included
with the unit.
1Hardware Installation
1. Insert SIM Cards and attach Antennae:
2. Take the bottom cover off by removing
the small screw at the bottom of the unit
and sliding the cover downwards
3. Connect the Safety Earth
Ground

OneStream GBRI Quick Start Guide
2
4. Replace the bottom cover by
sliding it back upwards and
replacing the screw.
5. Connect the first TE port
on the OneStream to an
available Trunk (S0) Port
on the PBX.
6. Connect the power to the unit and wait for
the Red LED to go out.

OneStream GBRI Quick Start Guide
3
2Programming
By default:
When OneStream starts up, it will try to find a DHCP Server to obtain an IP Address automatically.
If it does not find a DHCP server, it will use its default IP Address of 192.168.0.1.
2.1 Setting up your PC
In order to access the OneStream Web Interface and program the unit your PC must be set to a
compatible IP Address e.g. 192.168.0.2. To change the IP Address of your PC:
1. Click on the Start menu,
Control Panel (if you do not
see the display like this then
click on “Switch to Classic
View”):
2. Double-click on Network
Connections:

OneStream GBRI Quick Start Guide
4
3. Right-click the Local Area Connection icon
and click Properties:
4. Click on the Internet Protocol (TCP/IP)
entry and click the Properties button.
Click the Use the following IP address option
and fill in the details as shown here:
IP Address: 192.168.0.2
Subnet Mask: 255.255.255.0
Click the OK button to exit the Internet Protocol Properties window
Click the Close button to exit the Local Area Connection Properties window

OneStream GBRI Quick Start Guide
5
2.2 Editing the OneStream Programming
1. Connect one end of a Crossover
(X-Over) Ethernet Cable to the
LAN port of the OneStream:
2. Connect the other end of the Crossover Ethernet cable to the LAN port of your computer.
3. Open Internet Explorer web browser on your PC.
4. In the Address Bar of the Internet
Explorer window type the IP Address of
the OneStream unit 192.168.0.1 and
press the Enter key. You will see the
Login screen for the OneStream unit:
5. Enter the Password for the OneStream unit and click the Login button. The default password is
12345678. If the password entered is correct you will be taken to the Home page.
6. Click on the Routes link on the left of the page. The current routing table will then be displayed.
This may be correct if pre-configured by the supplier, if not it will have the default setting shown
here:

OneStream GBRI Quick Start Guide
6
7. To alter the routing to your requirements for Outbound GSM calls from the PBX, click the Edit icon
next to the route named TE to NT and set the following options:
•Change the Name of the route to TE to GSM
•In Destination Address change the ? to (for example) 08? in order to route any number
beginning with 08. The ? is a wild card that allows any digit dialled after the 08.
•In To Group change the NT to GSM
Click the Save button to save your changes and return to the routing table

OneStream GBRI Quick Start Guide
7
8. To alter the routing to your requirements for Inbound GSM calls to the PBX, click the Edit icon
next to the route named NT to TE and set the following options:
•Change the Name of the route to GSM to TE
•In From Group change the NT to GSM
•In Destination Address change the ? to sas this is required for an incoming call when no
destination address is set.
Click the Save button to save your changes and return to the routing table

OneStream GBRI Quick Start Guide
8
The Routing table should now look like this:
The OneStream is now ready for use.