Telit Wireless Solutions WE310F5-I Installation manual

1VV0301698 2021-01 Rev.0
Telit Technical Documentation
WE310F5-I/P EVB
Hardware User Guide
1VV0301663 Rev. 4 –2021-07-05

WE310F5-I/P EVB Hardware User Guide (CS2106A)
1VV0301663 Rev. 4 Page 2of 35 2021-07-05
APPLICABILITY TABLE
PART NUMBER
WE310F5-I
WE310F5-P

WE310F5-I/P EVB Hardware User Guide (CS2106A)
1VV0301663 Rev. 4 Page 3of 35 2021-07-05
Contents
APPLICABILITY TABLE 2
CONTENTS 3
1. INTRODUCTION 5
Scope 5
Audience 5
Contact Information, Support 5
Symbol Convention 5
Related Documents 6
2. GENERAL PRODUCT DESCRIPTION 7
Overview 7
3. WE310F5-I/P INTERFACE DESCRIPTION 8
WE310F5-I/P Development Kit 8
Antenna and Arduino Uno Rev 3 Connector 10
ESD Characteristics 11
3.3.1. Antenna connector: 11
3.3.2. UART 11
3.3.3. I2S, I2C connector 11
3.3.4. GPIO alternative function 12
3.3.5. RESET, Power Switch-Module, PB1-PB2, ARUDINO Enable 12
3.3.6. Program or Run switch 13
3.3.7. Audio jack 14
3.3.8. USB 2.0 and UART 14
3.3.9. EVB power configuration 14
3.3.10. SWD debug connector 16
3.3.11. LEDs and GPIOs 16
3.3.12. SPI-SDIO 17
4. WE310F5-I/P BASIC OPERATIONS 18
General Information on Power Supply 18
Program and Run the WE310F5-I/P Module 18
5. REVISION 19
Identification 19

WE310F5-I/P EVB Hardware User Guide (CS2106A)
1VV0301663 Rev. 4 Page 4of 35 2021-07-05
Change List 19
Known Issues 20
6. CONFORMITY ASSESSMENT ISSUES 21
Approvals summary 21
RED approval 21
6.2.1. RED Declaration of Conformity 21
6.2.2. Antennas 21
FCC and ISED approval 22
6.3.1. FCC Certificate 22
6.3.2. ISED approval/ISDE approbation 22
6.3.3. Applicable FCC and ISED rules 22
6.3.4. FCC and ISED Regulatory notices 22
6.3.5. Antennas 24
6.3.6. FCC Label and compliance information 26
6.3.7. ISED Label and compliance information 26
6.3.8. Information on test modes and additional testing requirements 27
6.3.9. FCC Additional testing, Part 15 Subpart B disclaimer 27
ANATEL Regulatory Notices 27
RoHS and REACH info 28
6.5.1. RoHS info 28
6.5.2. REACH info 28
Copyrights and Other Notices 29
7.1.1. Copyrights 29
7.1.2. Computer Software Copyrights 29
Usage and Disclosure Restrictions 30
7.2.1. License Agreements 30
7.2.2. Copyrighted Materials 30
7.2.3. High-Risk Materials 30
7.2.4. Trademarks 30
7.2.5. Third-Party Rights 30
7.2.6. Waiver of Liability 31
Safety Recommendations 31
9. DOCUMENT HISTORY 34

WE310F5-I/P EVB Hardware User Guide (CS2106A)
1VV0301663 Rev. 4 Page 5of 35 2021-07-05
1. INTRODUCTION
Scope
This document describes electrical specifications, mechanical information, interfaces
application, and manufacturing information about the Telit WE310F5-I/P Wi-Fi/BLE
module. With the help of this document and other application notes or user guides, users
can understand the Telit WE310F5-I/P Wi-Fi/BLE module well and develop various
products quickly.
Audience
This document is intended for Telit customers, especially system integrators, about to
implement their applications using the Telit module.
Contact Information, Support
For technical queries, support services, and to share documentation feedback, contact
Telit Technical Support at:
• TS[email protected]
• TS[email protected]
• TS[email protected]
• TS[email protected]
• TS[email protected]
Alternatively, you may visit http://www.telit.com/support
For detailed information about where you can buy the Telit modules or for
recommendations on accessories and components visit:
https://www.telit.com
Our aim is to make this guide as helpful as possible. Keep us informed of your comments
and suggestions for improvements.
Telit appreciates the user feedback on our information.
Symbol Convention
Table 1: Symbol Convention
Danger:This information MUST be followed, or catastrophic equipment
failure or personal injury may occur.

WE310F5-I/P EVB Hardware User Guide (CS2106A)
1VV0301663 Rev. 4 Page 6of 35 2021-07-05
Warning: Alerts the user on important steps about the module integration.
Note/Tip:Provides advice and suggestions that may be useful when
integrating the module.
Electro-static Discharge:Notifies the user to take proper grounding
precautions before handling the product.
All dates are in ISO 8601 format, that is YYYY-MM-DD.
Related Documents
Table 2: Related Documents
Module Name
Description
80664ST11034A
WE310F5-I/P AT Command Reference Guide
1VV0301662
WE310F5-I/P Moudle Hardware User Guide

WE310F5-I/P EVB Hardware User Guide (CS2106A)
1VV0301663 Rev. 4 Page 7of 35 2021-07-05
2. GENERAL PRODUCT DESCRIPTION
Overview
The Telit EVB is a rapid IoT Development Kit, in other words a system that reduces the
duration of IoT prototyping cycles from a matter of weeks or months to mere hours - all
by capitalizing on the combination of embedded IoT software and hardware. The system
was designed to provide a complete development environment to the user and intended
to be used with Telit WE310F5-I/P module and Arduino Uno Rev3 board.
Note/Tip:The combination of the EVB and the Arduino Uno Rev3 shall be
done according to the configuration described in this manual.
The information presented in this document is believed to be accurate and reliable.
However, no responsibility is assumed by Telit Communication S.p.A. for its use. No
license is granted by implication or otherwise under any patent rights of Telit
Communication S.p.A. other than for circuitry embodied in Telit products. This document
is subject to change without notice.

WE310F5-I/P EVB Hardware User Guide (CS2106A)
1VV0301663 Rev. 4 Page 8of 35 2021-07-05
3. WE310F5-I/P INTERFACE DESCRIPTION
WE310F5-I/P Development Kit
There are two types of EVB. Each of the two EVB is equipped with WE310F5-I and
WE310F5-P.Additionally, in case of WE310F5-P, the SMA antenna connector is mounted.
Following is the WE310F5-I/P EVB component details and its kitting parts:

WE310F5-I/P EVB Hardware User Guide (CS2106A)
1VV0301663 Rev. 4 Page 9of 35 2021-07-05
W-1
WE310F5-P Antenna Connector
10
ARDUINO Enable (PL705)
W-2
WE310F5-I RF Pad
11
UART1
1
UART (PL608)
12
GPIO- LED (PL606)
2
I2S-I2C (PL601)
13
UART0
3
GPIO –Alternate Function (PL302 –PL305)
14
Power Switch- EVB
4
General Purpose Button (PB1-PB2)
15
Power connector USB 2.0
5
Reset Button
16
Power Config (PL201-P204)
6
RUN/ PROGRAM Toggle Switch
17
SWD
7
Audio Jack
18
SPI-SDIO (PL604)
8
Power Switch- Module
19
LED
9
PB1-PB2 (PL605)

WE310F5-I/P EVB Hardware User Guide (CS2106A)
1VV0301663 Rev. 4 Page 10 of 35 2021-07-05
Table 3: WE310F5-I/P Kitting Parts
Description
Quantity
EVB Board
1
WIFI/BLE Antenna
1
Micro USB cable
1
Antenna and Arduino Uno Rev 3 Connector
The connectors on the bottom are intended to plug Arduino Uno Rev 3 to create a Kit
suitable for IoT development. The WE310F5-I/P EVB can be used as Arduino Shield.
The bottom side view of the EVB are shown below:
1
ARDUINO Connectors
2
WE310F5-P Antenna Connector