Tempo Fitness YPF-603 User manual

Instruction Manual
Distributed by Tempo (Aust) Pty Ltd ABN 70 106 100 252
PO Box 6056,
Frenchs Forest LC NSW 2086
Fax: [phone]
Email: [email protected]
Customer Helpline: 1300 886 649
This product has a 12 month warranty when
accompanied by proof of purchase.
Steam Iron
YPF-603
1
8

27
Important Safety Instructions
Please keep this instruction manual in a safe place, along with the
warranty card, purchase receipt and carton for future reference. The
safety precautions enclosed herein reduce the risk of fire, electric
shock and injury when correctly adhered to.
- If the supply cord is damaged, it must be replaced by the
manufacturer or its service agent or a similarly qualified person in order
to avoid a hazard.
- Before turning on, ensure the electrical voltage and frequency of the cir-
cuit correspond to those indicated on the appliance.
- The appliance is not intended for use by young children or infirm
persons without supervision.
- Young children should be supervised to ensure that they do not play
with the appliance.
- Do not operate the appliance outdoors
- Power plug must be removed from power socket before cleaning, serv-
icing, maintenance or moving the appliance.
- When the appliance is not in use, switch it off and unplug it.
- The appliance should be placed on a flat surface when operating to
avoid overturning.
- To reduce the risk of electrocution, never operate this appliance with
wet hands, submerge under water or spill liquids into the product.
- Do not insert any objects into the appliance.
- Do not kink or damage the power cord.
- Improper installation may result in the risk of fire, electric shock and or
injury to persons.
- The manufacturer is not responsible for any eventual damages caused
by improper or faulty use.
- The unit has no user-serviceable parts contained within. Do not attempt
to repair, disassemble or modify the appliance.
A NIG C B D F
E
H K L

3
6
Safety Instructions continued:
- Before first use, remove any stickers or protective foil from the sole plate
and clean the sole plate with a soft cloth.
- Unplug the iron from the mains prior to;
Filling the iron with water or pouring the remaining water out after use.
Cleaning the iron.
- When you have finished ironing and also when leaving the iron even for
a short time;
Set the steam iron control to the “0” position,
Stand the iron on its end,
Remove the power plug from the wall socket.
- Do not put vinegar, starch, chemically descaled water or descaling
agents in the water reservoir.
- The cord should not touch the sole plate while it is hot.
- The ejected steam is hot and therefore hazardous. Never direct the
steam at other people as it could burn them.
- Always keep the iron in a safe dry place, standing on its end.
- Never immerse the iron in water.

5
4
Ironing Temperature Guides
1 - Always follow the ironing instructions on the garment label. If these
instructions are missing but you do know what fabric the garment is made
from, check the table for directions.
2 - The Table is valid for garments only and is not applicable to any
applied finish, gloss etc. Textiles to which some kind of finish (gloss, wrin-
kle, relief etc) has been applied, are best ironed at lower temperatures.
3 - Sort the laundry according to ironing temperature required. Eg wool
items together, cotton with cotton etc.
4 - The Iron heats up quicker than it cools down. Therefore always start
ironing garments that require lower temperatures first such as synthetics.
5 - If the garment is made of a mixture of fabrics, select the fabric that
requires the lowest ironing temperature and set the Iron at this setting.
6 - If you do not know what fabric the garment is made from, find a spot
on the garment that will not show when wearing or using the garment.
Starting at the lower temperatures, increase heat till good results are
achieved.
7 - Pure woollen fabrics (100% wool) may be pressed with the Iron set
to a steam position. Preferably set the steam control (B) to the maximum
position and use a dry pressing cloth.
8 - When steam ironing woollen fabrics, marks can appear on the fabric.
To avoid this, either use a pressing cloth or turn the articles inside out and
iron the reverse side.
9 - Velvet and other fabrics which can rapidly acquire shiny spots should
be ironed in one direction only with light pressure. Always keep the iron
moving while ironing.
10 - When ironing silk or synthetic materials, iron the reverse side and do
not use sprays as they could stain.
Filling with Water (for steam ironing and spraying)
1 - Remove the power plug from the wall socket before filling (or empty-
ing) the iron with water.
2 - Set the steam control (B) to “0” position.
3 - Fill the filling cup with water (max 200ml), tilt the iron slightly and pour
the water into the filling aperture till the iron reaches maximum level.
4 - Use normal tap water when using for the first time.
5 - After initial use, distilled water may be used if the tap water is very
hard. Do not put vinegar, starch, chemically descaled water or des-
caling agents in the water resevoir.
Setting the Temperature
1 - Stand the iron on its end.
2 - Set the temperature control (A) to the correct ironing temperature.
3 - Insert the power plug into the wall socket.
4 - After the temperature pilot light (I) has first gone out, you may start
ironing. The pilot light will come back on from time to time during ironing.
5 - If you set the temperature to a lower setting after ironing at a high tem-
perature, do not begin ironing untill the pilot light (I) has come on and then
turned off again. Otherwise you may scorch the fabric as the iron will still
be too hot.
Steam Ironing
1 - To iron without steam, set the steam control (B) to position “0”.
2 - Ensure there is enough water in the water reservoir prior to using
steam.
3 - Set the steam control;
Use the “0” (no steam) when ironing at temperatures between MIN and • •
Steam setting for temperature settings between • • and • • •
Maximum steam setting for temperatures between • • • and MAX.
Water may leak from the sole plate if too low a temperature is select-
ed for the steam setting.