Terex RL4000D2 User manual

Service Manual
RL4000D2
First Edition
First Printing
Part No. 116473
September 2008
Courtesy of Machine.Market

September 2008
RL4000 Light Tower Part No. 116473
ii
Important
Read, understand and obey the safety rules and
operating instructions in the appropriate Operator's
Manual on your machine before attempting any
maintenance procedure.
Basic mechanical, hydraulic and electrical
skills are required to perform most procedures.
However, several procedures require specialized
skills, tools, lifting equipment and a suitable
workshop. In these instances, we strongly
recommend that maintenance and repair be
performed at an authorized TEREX dealer
service center.
Technical Publications
TEREX Corporation has endeavored to deliver the
highest degree of accuracy possible. However,
continuous improvement of our products is a
TEREX policy. Therefore, product specifications
are subject to change without notice.
Readers are encouraged to notify TEREX of errors
and send in suggestions for improvement. All
communications will be carefully considered for
future printings of this and all other manuals.
Copyright © 2008 by TEREX Corporation
116473 Rev A September 2008
First Edition, Second Printing
"TEREX" is a registered trademark of TEREX
Corporation in the USA and many other countries.
"Super Quiet" is a trademark of TEREX
Corporation.
Printed on recycled paper
Printed in U.S.A.
Contact Us:
www.TEREX.com
Serial Number Information
TEREX Corporation offers the following manuals
for these models:
Title Part No.
TEREX RL4000 Operator's Manual .................... 116417
First Edition
TEREX RL4000 Service Manual ........................ 116473
First Edition
TEREX RL4000 Part's Manual ........................... 116444
First Edition
Leroy Somer Manual ........................................... 116118
Kubota Engine Manual ....................................... 893020
Axis Manual ........................................................ 116117
Marathon Manual ................................................ 116188
Introduction
Courtesy of Machine.Market

September 2008
Part No. 116473 RL4000 Light Tower
Serial Number Legend
The serial number plate on your RL4000 is located
on the cabinet next to the light tower mast.
iii
How to Read Your Serial Number
Courtesy of Machine.Market

September 2008
RL4000 Light Tower Part No. 116473
This page intentionally left blank.
iv
Courtesy of Machine.Market

September 2008
Part No. 116473 RL4000 Light Tower v
Danger
Failure to obey the instructions and safety rules
in this manual and the appropriate Operator's
Manual on your machine will result in death or
serious injury.
Many of the hazards identified in the
operator’s manual are also safety hazards
when maintenance and repair procedures
are performed.
Do Not Perform Maintenance
Unless:
You are trained and qualified to perform
maintenance on this machine.
You read, understand and obey:
- manufacturer’s instructions and safety rules
- employer’s safety rules and worksite
regulations
- applicable governmental regulations
You have the appropriate tools, lifting
equipment and a suitable workshop.
Safety Rules
Section 1 • Safety Rules
Courtesy of Machine.Market

September 2008
RL4000 Light Tower Part No. 116473
REV ASAFETY RULES
Personal Safety
Any person working on or around a machine must
be aware of all known safety hazards. Personal
safety and the continued safe operation of the
machine should be your top priority.
Read each procedure thoroughly. This
manual and the decals on the machine,
use signal words to identify the following:
Safety alert symbol—used to alert
personnel to potential personal
injury hazards. Obey all safety
messages that follow this symbol
to avoid possible injury or death.
Red—used to indicate the
presence of an imminently
hazardous situation which, if not
avoided, will result in death or
serious injury.
Orange—used to indicate the
presence of a potentially
hazardous situation which, if not
avoided, could result in death or
serious injury.
Yellow with safety alert symbol—
used to indicate the presence of a
potentially hazardous situation
which, if not avoided, may cause
minor or moderate injury.
Yellow without safety alert
symbol—used to indicate the
presence of a potentially
hazardous situation which, if not
avoided, may result in property
damage.
Green—used to indicate operation
or maintenance information.
Be sure to wear protective eye wear and
other protective clothing if the situation
warrants it.
Be aware of potential crushing hazards
such as moving parts, free swinging or
unsecured components when lifting or
placing loads. Always wear approved steel-toed
shoes.
Workplace Safety
Be sure to keep sparks, flames and
lighted tobacco away from flammable and
combustible materials like battery gases
and engine fuels. Always have an approved fire
extinguisher within easy reach.
Be sure that all tools and working areas
are properly maintained and ready for
use. Keep work surfaces clean and free of
debris that could get into machine components and
cause damage.
Be sure that your workshop or work area
is properly ventilated and well lit.
Be sure any forklift, overhead crane or
other lifting or supporting device is fully
capable of supporting and stabilizing the
weight to be lifted. Use only chains or straps that
are in good condition and of ample capacity.
Be sure that fasteners intended for one
time use (i.e., cotter pins and self-locking
nuts) are not reused. These components
may fail if they are used a second time.
Be sure to properly dispose of old oil or
other fluids. Use an approved container.
Please be environmentally safe .
vi
Section 1 • Safety Rules
Courtesy of Machine.Market

September 2008
Part No. 116473 RL4000 Light Tower
REV A Table of Contents
Introduction
Important Information - Introduction ................................................................... ii
How to Read Your Serial Number ..................................................................... iii
Parts Stocking List ............................................................................................ ix
How to Order Parts ........................................................................................... xi
Service Parts Fax Order Form ......................................................................... xii
Section 1 Safety Rules
General Safety Rules ........................................................................................ v
Section 2 Rev Specifications
A Specifications .............................................................................................. 2 - 1
A Specifications (Continued) ........................................................................... 2 - 2
A Specifications (Continued) ........................................................................... 2 - 3
A Torque Specifications .................................................................................. 2 - 4
Section 3 Rev Scheduled Maintenance Procedures
Introduction .................................................................................................. 3 - 1
Pre-delivery Preparation Report................................................................... 3 - 2
AMaintenance Schedules
Kubota Lubrication and Maintenance Service Intervals................................ 3 - 3
Leroy Somer Generators Maintenance Schedule ........................................ 3 - 4
Marathon Generators Maintenance Schedule .............................................. 3 - 5
Section 4 Rev Troubleshooting
Introduction .................................................................................................. 4 - 1
A Troubleshooting Guide................................................................................. 4 - 2
vii
Courtesy of Machine.Market

September 2008
RL4000 Light Tower Part No. 116473
REV ATABLE OF CONTENTS
Section 5 Rev Schematics
A Introduction .................................................................................................. 5 - 1
A AC Light Tower Wiring ................................................................................. 5 - 2
A Wire Harness, Control Box, European, DC .................................................. 5 - 3
A DC Wiring, European, Kubota ...................................................................... 5 - 4
A DC Wiring, Kubota ....................................................................................... 5 - 5
A Wire Harness, Inside Control Box, DC ......................................................... 5 - 6
A MH or HPS Light Fixture .............................................................................. 5 - 7
A 1000 MH Ballast .......................................................................................... 5 - 8
A 1000 HPS Ballast ......................................................................................... 5 - 9
viii
Courtesy of Machine.Market

September 2008
Part No. 116473 RL4000 Light Tower
REV A
ix
Parts Stocking List
Required Parts
The following parts are required to perform
maintenance procedures as outlined in the
TEREX RL4000 Parts and Service Manuals.
Description Part No.
Kubota Models
Oil Filter .............................................................. 866050
Air Filter .............................................................. 866127
Fuel Filter ........................................................... 839200
V-belt .................................................................. 839209
Courtesy of Machine.Market

September 2008
RL4000 Light Tower Part No. 116473
REV A
x
This page intentionally left blank.
Courtesy of Machine.Market

September 2008
Part No. 116473 RL4000 Light Tower
REV A
Machine Information
Model
Serial Number
Date of Purchase
Authorized TEREX Distributor
Phone Number
Please be prepared with the following information
when ordering replacement parts for your TEREX
product:
Machine model number
Machine serial number
Terex part number
Part description and quantity
Purchase order number
"Ship to" address
Desired method of shipment
Name and telephone number of the
authorized TEREX Distributor in your area
Use the Service Parts Fax Order Form on the
next page and fax your order to our Parts
Department.
If you don't know the name of your authorized
distributor, or if your area is not currently serviced
by an authorized distributor, please call TEREX
Corporation.
How To Order Parts
xi
Genie Industries
18340 NE 76th Street
P.O. Box 97030
Redmond, WA 98073-9730
Telephone [phone]
Fax [phone]
genieindustries.com
Courtesy of Machine.Market

September 2008
RL4000 Light Tower Part No. 116473
Part Number Description Quantity Price
All backordered parts will be shipped when available via the same ship method as the original order
unless noted below:
oShip complete order only - no backorders
oShip all available parts and contact customer on disposition of backordered parts
oOther (please specify)
Please fill out completely
Date _________________________________ Account Number _______________________________
Your Name ______________________________ Your Fax Number _____________________________
_________________________________ Your Phone Number ____________________________
Bill To _________________________________ Ship To ___________________________________
_________________________________ ___________________________________
_________________________________ ___________________________________
_________________________________ ___________________________________
Purchase Order Number ____________________ Ship Via ___________________________________
Model(s) ______________________________________________________ Serial No.(s) _________________
Optional Equipment __________________________________________________________________________
FOR TEREX USE ONLY
Order Number ______________ Origin Code ________________ Comments _________________________
Date Scheduled ____________ Ship Condition ______________ __________________________________
Order Total ________________ Terms Code ________________ __________________________________
remove this page and make copies remove this page and make copies
Service Parts fax Order Form
FAX TO: [phone] OR TOLL FREE: 877-367-5606
Courtesy of Machine.Market

REV A
PartNo.116473 RL4000LightTower 2 - 1
Section 2 • Specifications
September2008
Specifications
MAST
MAST ELEVATION 30' / 9.14M
TOWER ROTATION 359 DEGREES
TOWER ROTATION MANUAL
MAX WIND RATING 62MPH / 100KPH
DIMENSIONS SEE CHART ON PAGE 2-3
ENGINES
STANDARD KUBOTA, D1105
DIESEL, 13.6 HP
GENERATORS
STANDARD MARATHON, 6 KW
201CSA5411, 60HZ
OR LEROY SOMER
36M6, 6KW, 60HZ
STANDARD
RECEPTACLES QTY. 1, 120V, 20A, GFI, DUPLEX
QTY. 1, 240V, 30A, TWISTLOCK
STANDARD
BREAKERS QTY. 4, 1P, 15A, LAMPS
QTY. 1, 2P, 30A, MAIN
QTY. 1, MINI, 1P, 20A, GFI RECEPTACLE
STANDARD
LAMPS SEPARATELY SWITCHED
QTY. 4, 1000 WATT
METAL HALIDE, ROUND
Courtesy of Machine.Market

REV A
2 - 2 RL4000LightTower PartNo.116473
Section 2 • Specifications September2008
SPECIFICATIONS
TRAILER WHEELS 13 X 4.5, 5 HOLE
TIRES, ST175/80D13, LOAD B
COLD PRESSURE, 35PSI / 250KPA
AXLE RATING 2000LBS
MAX TOW SPEED, 60MPH / 96KPH
NO BRAKES, STANDARD
TWO OUTRIGGERS, STANDARD
FUEL TANK FUEL TYPE, NO.2 DIESEL ONLY
CAPACITY, 30 GALLONS / 114L
MATERIAL, POLYETHELENE
FUEL
CONSUMPTION KUBOTA, .787 G/HR - 2.97L/HR
KUBOTA, RUN TIME, 30 GAL.= 38.3 HRS.
WEIGHT 6KW, TOTAL WEIGHT, NO FUEL, 1,725LBS. / 783KG
6KW, TOTAL WEIGHT, TANK FULL, 1,935LBS. / 878KG
TONGUE WEIGHT 6KW, 30 GALLON, 199LBS / 91KG
WITH FUEL
BATTERY WET, 12V, GROUP 24, 460 CCA, STD-DUTY, LEAD ACID
Courtesy of Machine.Market

REV A
PartNo.116473 RL4000LightTower 2 - 3
Section 2 • Specifications
September2008
SPECIFICATIONS
Courtesy of Machine.Market

REV A
2 - 4 RL4000LightTower PartNo.116473
Section 2 • Specifications September2008
SPECIFICATIONS
SIZE THREAD
in-lbs Nm in-lbs Nm in-lbs Nm in-lbs Nm in-lbs Nm
20 100 11.3 80 9 140 15.8 110 12.4 130 14.7
28 90 10.1 120 13.5 120 13.5 160 18 140 15.8
ft-lbs Nm ft-lbs Nm ft-lbs Nm ft-lbs Nm ft-lbs Nm
18 13 17.6 17 23 18 24 25 33.9 21 28.4
24 14 19 19 25.7 20 27.1 27 36.6 24 32.5
16 23 31.2 31 42 33 44.7 44 59.6 38 51.5
24 26 35.2 35 47.4 37 50.1 49 66.4 43 58.3
14 37 50.1 49 66.4 50 67.8 70 94.7 61 82.7
20 41 55.5 55 74.5 60 81.3 80 108.4 68 92.1
13 57 77.3 75 101.6 80 108.4 110 149 93 126
20 64 86.7 85 115 90 122 120 162 105 142
12 80 108.4 110 149 120 162 150 203 130 176
18 90 122 120 162 130 176 170 230 140 189
11 110 149 150 203 160 217 210 284 180 244
18 130 176 170 230 180 244 240 325 200 271
10 200 271 270 366 280 379 380 515 320 433
16 220 298 300 406 310 420 420 569 350 474
9320 433 430 583 450 610 610 827 510 691
14 350 474 470 637 500 678 670 908 560 759
8480 650 640 867 680 922 910 1233 770 1044
12 530 718 710 962 750 1016 990 1342 840 1139
7590 800 790 1071 970 1315 1290 1749 1090 1477
12 670 908 890 1206 1080 1464 1440 1952 1220 1654
7840 1138 1120 1518 1360 1844 1820 2467 1530 2074
12 930 1260 1240 1681 1510 2047 2010 2725 1700 2304
61460 1979 1950 2643 2370 3213 3160 4284 2670 3620
12 1640 2223 2190 2969 2670 3620 3560 4826 3000 4067
5/16
3/8
7/16
1/2
1.5
9/16
5/8
3/4
7/8
1
1.125
1.25
LUBED
1/4
LUBED DRY LUBED DRY
LUBEDDRYLUBED
SAE FASTENER TORQUE CHART
Grade 5
DRYLUBED
• This chart is to be used as a guide onlyunless noted elsewhere in this manual •
A574 High Strength
Black Oxide Bolts
Grade 8
Size
(mm) in-lbs Nm in-lbs Nm in-lbs Nm in-lbs Nm in-lbs Nm in-lbs Nm in-lbs Nm in-lbs Nm
516 1.8 21 2.4 41 4.63 54 6.18 58 6.63 78 8.84 68 7.75 91 10.3
619 3.05 36 4.07 69 7.87 93 10.5 100 11.3 132 15 116 13.2 155 17.6
745 5.12 60 6.83 116 13.2 155 17.6 167 18.9 223 25.2 1.95 22.1 260 29.4
ft-lbs Nm ft-lbs Nm ft-lbs Nm ft-lbs Nm ft-lbs Nm ft-lbs Nm ft-lbs Nm ft-lbs Nm
85.4 7.41 7.2 9.88 14 19.1 18.8 25.5 20.1 27.3 26.9 36.5 23.6 32 31.4 42.6
10 10.8 14.7 14.4 19.6 27.9 37.8 37.2 50.5 39.9 54.1 53.2 72.2 46.7 63.3 62.3 84.4
12 18.9 25.6 25.1 34.1 48.6 66 64.9 88 69.7 94.5 92.2 125 81 110 108 147
14 30.1 40.8 40 54.3 77.4 105 103 140 110 150 147 200 129 175 172 234
16 46.9 63.6 62.5 84.8 125 170 166 226 173 235 230 313 202 274 269 365
18 64.5 87.5 86.2 117 171 233 229 311 238 323 317 430 278 377 371 503
20 91 124 121 165 243 330 325 441 337 458 450 610 394 535 525 713
22 124 169 166 225 331 450 442 600 458 622 612 830 536 727 715 970
24 157 214 210 285 420 570 562 762 583 791 778 1055 682 925 909 1233
LUBED DRY LUBED DRYLUBED DRY LUBED DRY
LUBEDDRYLUBED
Class 12.9Class 4.6
DRYLUBED
METRIC FASTENER TORQUE CHART
• This chart is to be used as a guide only unless noted elsewhere in this manual •
LUBED DRY
Class 10.9Class 8.8
DRY
10.9 12.98.84.6
Courtesy of Machine.Market

REV A
Section3 • ScheduledMaintenanceProcedures
PartNo.116473 RL4000LightTower 3 - 1
September2008
Scheduled Maintenance Procedures
Observe and Obey:
Maintenance inspections shall be completed by
a person trained and qualified on the
maintenance of this machine.
Scheduled maintenance inspections shall be
completed as specified using the supplied
Lubrication and Maintenance Service Interval
Charts provided in this section.
Failure to perform each procedure
as presented and scheduled could
result in death, serious injury or
substantial damage.
Immediately tag and remove from service a
damaged or malfunctioning machine.
Repair any machine damage or malfunction
before operating the machine.
Keep records on all inspections for three years.
Machines that have been out of service for a
period longer than 3 months must complete the
quarterly inspection.
Unless otherwise specified, perform each
maintenance procedure with the machine in the
following configuration:
· Machine parked on a firm, level surface
· Toggle switch in the "OFF" position
· Wheels chocked
About This Section
This section contains detailed procedures for each
scheduled maintenance inspection.
Each procedure includes a description, safety
warnings and step-by-step instructions.
Symbols Legend
Safety alert symbol—used to alert
personnel to potential personal
injury hazards. Obey all safety
messages that follow this symbol
to avoid possible injury or death.
Red—used to indicate the
presence of an imminently
hazardous situation which, if not
avoided, will result in death or
serious injury.
Orange—used to indicate the
presence of a potentially
hazardous situation which, if not
avoided, could result in death or
serious injury.
Yellow with safety alert symbol—
used to indicate the presence of a
potentially hazardous situation
which, if not avoided, may cause
minor or moderate injury.
Yellow without safety alert
symbol—used to indicate the
presence of a potentially
hazardous situation which, if not
avoided, may result in property
damage.
Green—used to indicate operation
or maintenance information.
Indicates that a specific result is expected after
performing a series of steps.
Indicates that an incorrect result has occurred
after performing a series of steps.
Courtesy of Machine.Market

Copyright © 2006 by TEREX Corporation. TEREX® is a registered trademark of TEREX
Corporation.
Rev B
Pre-DeliverPre-Deliver
Pre-DeliverPre-Deliver
Pre-Delivery Preparationy Preparation
y Preparationy Preparation
y Preparation
Pre-Delivery Preparation Y N R
Pre-operation inspection completed
Maintenance items completed
Function tests completed
Model
Serial number
Date
Machine owner
Inspected by (print)
Inspector signature
Inspector title
Inspector company
Instructions
Use the operator’s manual on your machine.
The Pre-delivery Preparation consists of completing the
Pre-operation Inspection, the Maintenance items and the
Function Tests.
Use this form to record the results. Place a check in the
appropriate box after each part is completed. Follow the
instructions in the operator’s manual.
If any inspection receives an N, remove the machine from
service, repair and re-inspect it. After repair, place a check
in the R box.
Legend
Y = yes, completed
N = no, unable to complete
R = repaired
Comments
Fundamentals
It is the responsibility of the dealer to perform the
Pre-delivery Preparation.
The Pre-delivery Preparation is performed prior to each
delivery. The inspection is designed to discover if anything
is apparently wrong with a machine before it is put into
service.
A damaged or modified machine must never be used. If
damage or any variation from factory delivered condition is
discovered, the machine must be tagged and removed
from service.
Repairs to the machine may only be made by a qualified
service technician, according to the manufacturer's
specifications.
Scheduled maintenance inspections shall be performed by
qualified service technicians, according to the
manufacturer's specifications and the requirements listed
in the responsibilities manual.
TEREX Rock Hill
P.O. BOX 3147
Rock Hill, SC 29732 USA
Toll Free [phone] in U.S.A. and Canada
Courtesy of Machine.Market

REV A
Section3 • ScheduledMaintenanceProcedures
PartNo.116473 RL4000LightTower 3 - 3
September2008
Maintenance Schedules
ITEM Every 50
Hours
Every
100
Hours
Every
200
Hours
Every
400
Hours
Every
500
Hours
Every
Year
Every
800
Hours
Every
1500
Hours
Every
3000
Hours
Every
Two
Years
Check of fuel pipes and clamp bands •
Check engine oil and coolant level •
Cleaning of air cleaner element •
Check of battery electrolyte level •
Check of fan belt tightness •
Check of radiator hoses and clamp
bands •
Check of intake air line •
Replacement of oil filter cartridge •
Replacement of fuel filter cartridge •
Removal of sediment in fuel tank •
Cleaning of water jacket (radiator
interior) •
Replacement of fan belt •
Replacement of air cleaner element •
Check of damage in electric wiring
and loose connections •
Check of valve clearance •
Check of fuel injection nozzle injection
pressure •
Check of turbo charger •
Check of injection pump •
Check of injection timer •
Change of radiator coolant (L.L.C.) •
Replacement of battery •
Replacement of radiator hoses and
clamp bands •
Replacement of fuel pipes and clamp
bands •
Replacement of intake air line •
Kubota Lubrication and Maintenance Service Intervals
*Refer to the manufacturer's manuals for detailed maintence intervals and instructions. If the
information in the manufacturer's manual differs from that in this manual the manufacturer's manual
should take precedence.
Courtesy of Machine.Market

REV A
Section3 • ScheduledMaintenanceProcedures
3 - 4 RL4000LightTower PartNo.116473
September2008
MAINTENANCE SCHEDULES CONTINUED
ITEM DAILY Weekly 2000 Hours
or 6 Months 8000 Hours or 1 Year 20000 Hours or 3 Years 30000 Hours or 5 Years
Inspect and verify operator reports •
Visual inspection of generator housing and air
inlet/outlets •
Visually inspect installation for sign of particulate
or liquid contaminant instrusion. •
Check control panel voltmeter for proper stability
and voltage output. Monitor the power factor and
generator loading during operation. •
Visually inspect the generator non-drive end
bearing exterior for dirt, and clean if necessary. •
If installed, inspect any generator air filters for
build up of contaminants, and clean or replace as
required. •
Visually inspect the stator output leads and
insulation for cracking or damage. •
Check all exposed electrical connections for
tightness. •
Check transformers, fuses, capacitors, and
lightning arrestors for loose or physical damage. •
Check all lead wires and electrical connections for
proper clearance and spacing. •
Clean the inside of the outlet box, air screens and
air baffles with compressed air or electrical
solvent if needed. •
Check machine vibrations and bearing condition
against those established and recorded during
original commissioning period or as defined by
OEM. •
Check IR (insulation resistance) to ground on all
generator windings, including the main rotating
assembly, the main stator assembly, the exciter
field and armature assemblies, and any optional
PMG assembl
y
- record
•
Remove the end brackets and visually inspect the
generator end windings for oil or dirt
contamination. Excessive contamination may
necessitate surface cleaning*.
•
Disassemble the generator (this includes rotor
removal). •
Clean the generator windings. •
Replace the bearings •
Leroy Somer Generators Maintenance Schedule
*Refer to the manufacturer's manuals for detailed maintence intervals and instructions. If the
information in the manufacturer's manual differs from that in this manual the manufacturer's manual
should take precedence.
Courtesy of Machine.Market