Tescom NEOLINE PRO 1kVAS User manual

ONLINE UPS
1-3 kVA
Uninterruptible Power Supply System
User Manual
1 phase In / 1 phase Out
NEOLINE PRO
Βόλου 7, 183 46 Μοσχάτο
Volou 7, 18 346, Moschato, Greece
[phone]
[email protected] www.tescom-ups.gr

www.tescom-ups.gr
NEOLINE PRO �1/1 �1-3 kVA �ONLINE UPS
USER MANUAL
Table of Contents
1 Safety Information ................................................................................. 1
1.1 UPS safety information ........................................................................... 1
1.2 Battery safety information ....................................................................... 1
2 Product Overview .................................................................................. 3
2.1 Specifications .......................................................................................... 3
2.2 Rear panel features................................................................................. 5
3 Installation.............................................................................................. 7
3.1 Unpacking inspection .............................................................................. 7
3.2 Installation information ............................................................................ 7
3.3 Installation and output connection .......................................................... 8
4 Network Functions ................................................................................ 8
4.1 Communication port ................................................................................ 8
4.2 EPO port（optional）......................................................................................9
4.3 Intelligent card (optional) ......................................................................... 9
5 Operation.............................................................................................. 10
5.1 Button operation .................................................................................... 10
5.2 Display interface....................................................................................11
5.3 UPS On/Off operation ........................................................................... 12
5.4 UPS Settings .........................................................................................13
5.5 Parameters inquiring operation .............................................................14
5.6 Operation mode..................................................................................... 16
6 Fault Messages....................................................................................17
7 Troubleshooting ..................................................................................21

1
NEOLINE PRO �1/1 �1-3 kVA �ONLINE UPS
USER MANUAL
1 Safety Information
1.1 UPS safety information
Read all safety information and operating instructions carefully before attempting to
install, service or maintain the UPS. Save this manual properly for reuse.
This UPS is intended for indoor use only.
Do not operate this UPS in direct sunlight, in contact with fluids, or where there is
excessive dust or humidity.
Be sure the air vents on the UPS are not blocked. Allow adequate space against
the wall for proper ventilation.
Do not open the UPS case as you will, there is a high risk of electric shocks inside.
All connection/wiring/servicing must be performed by a qualified electrician.
Do not connect to the equipment like hair dryer or electric heater.
Do not use liquid extinguisher if there is a fire, a dry powder extinguisher is
recommended.
CAUTION
UPS has high voltage inside, do not repair it by yourself. If any questions, please
contact local service center or dealer.
1.2 Battery safety information
Environmental factors impact battery life. Elevated ambient temperatures, poor
quality utility power, and frequent short duration discharges will shorten battery life.
Replacing battery periodically can help to keep UPS in normal state and assure
backup time required.
Battery installing or replacing should be performed by a qualified electrician. If you
want to replace the battery cable, please purchase it from our local service center
or distributors to avoid fever and lighter which can cause fire by inadequate power
capacity.
Batteries may cause electric shocks and have a high short circuit current, follow
below requirements before installing or replacing the batteries.
A. Remove wristwatches, rings, jewelry and other conductive materials.
B. Only use tools with insulated grips and handles.
C. Wear insulated shoes and gloves.
D. Do not put the metal tools or parts on the batteries.
E. Before disconnecting the terminals from the batteries, cut off all the loads
to the batteries first.

2www.tescom-ups.gr
NEOLINE PRO �1/1 �1-3 kVA �ONLINE UPS
USER MANUAL
Do not dispose of the batteries with fire. The batteries may explode.
Do not open or mutilate batteries. Released electrolyte inside is harmful to the skin
and eyes, and maybe toxic.
Do not connect the positive pole and negative pole directly, otherwise it will cause
electric shocks or will be on fire.
The battery circuit is not isolated from the input voltage, high voltage may occur
between the battery terminals and ground, check if there is no voltage there before
touching.
Note：
：
Symbol instructions:
Symbol Significations Symbol Significations
Caution
Protective earth
Danger! High Voltage!
Disable/mute audible
alarm
Turn on
Overload
Turn off Battery inspection
Standby or Shutdown
Repeat
AC
Display screen repeat key
DC
Battery

3
NEOLINE PRO �1/1 �1-3 kVA �ONLINE UPS
USER MANUAL
2 Product Overview
2.1 Specifications
Model
1KVA S(T)
1KVA XL(T)
2KVA S(T)
2KVA XL(T)
3KVA S(T)
3KVA XL(T)
Rated Capacity
1 kVA / 900 W
2 kVA / 1800 W
3 kVA / 2700 W
Input
Rated input voltage
208 Vac / 220 Vac / 230 Vac / 240 Vac
Rated input frequency
50 Hz / 60 Hz (auto-sense)
Input voltage range
110 ~ 176Vac (power derating linearly between 50% and 100% load);
176 ~ 280Vac (no derating); 280 ~ 300Vac (power derating 50%)
Input frequency range
40~70 Hz
PFC
≥0.99
THDI
≤ 6%
Bypass voltage range
-25% ~ +15% (settable)
Output
Output voltage
208 Vac / 220 Vac / 230 Vac / 240 Vac (settable)
Voltage accuracy
±1%
Output PF
0.9
Inverter overload
capability
105% ~ 125% load: transfer to bypass in 1 min;125% ~ 150% load: transfer to
bypass in 30 s;
>150% load: transfer to bypass in 300 ms;
Load crest
3:1
From mains mode to
BAT mode
0ms (transfer time)
From mains mode to
bypass
4 ms (typical)
Efficiency
Line mode
90%
91%
92%
BAT mode
85%
86%
87%
ECO mode
95%
96%
97%
Output
frequency
Line mode
Same as input frequency
BAT mode
(50 / 60 ±0.1) Hz
Total voltage harmonic
distortion
≤2% (linear load); ≤ 5% (non-linear load)

4www.tescom-ups.gr
NEOLINE PRO �1/1 �1-3 kVA �ONLINE UPS
USER MANUAL
Batteries
Battery type Sealed lead acid maintenance free battery
DC voltage 24 V 36 V 36 V 48 V 72 V 72 V 72 V 96 V 96 V
Inbuilt battery
12 V / 9
Ah
12 V /
7
Ah
/ 12 V / 9
Ah
12 V /
7
Ah
/ 12 V /
9 Ah
12 V / 7
Ah
/
Quantity 2 3 3 4 6 6 6 8 8
Charger output
voltage
27.1
±0.4
40.7
±0.6
40.7
±0.6
54.2
±0.8
81.3
±1.2
81.3
±1.2
81.3
±1.2
108.4
±1.6
108.4
±1.6
Recharging time Recover 90% capacity in 3 hours for standard models
Charging current
(Max.)
Standard model: 1 A
Long time model: 6A /12A
System Control and Communications
Protections
Over-temp protection; Fan testing protection; Overload protection; Output
short circuit protection; Battery discharge protection
Communication port Standard: RS232; Options: USB, SNMP card, dry contacts
Display LCD
Environmental
Operating humidity 0 ~ 90 % RH @ 0 ~ 40°C (non-condensing)
Storage temperature -25°C ~ 55°C(exclude batteries)
Operating altitude ≤1000m, above 1000m, derate 1% for each rising 100m
Protection class IP20
Noise level ≤50dB (at 1m)
Others
Dimensions (mm)
W × D ×H
440×468×88 440×658×88
440×
468×88
440×
658×88
440×468×88
Weight (kg) 12.26 13.78 7.58 22.73 25.86 9.66 29.26 9.45 10.04
* Derate capacity to 70% in CUCF mode and to 90% when the output voltage is adjusted to 208Vac.
Note：
Model Type Model Type
1kVA S(T) 1 kVA Standard model 1kVA XL(T) 1 kVA Long backup model
2kVA S(T) 2 kVA Standard model 2kVA XL(T) 2 kVA Long backup model
3kVA S(T) 3 kVA Standard model 3kVA XL(T) 3 kVA Long backup model

5
NEOLINE PRO �1/1 �1-3 kVA �ONLINE UPS
USER MANUAL
2.2 Rear panel features
a. 1ΚVA S(T) (DC24V)
b. 2ΚVA S(T) (DC24V)

6www.tescom-ups.gr
NEOLINE PRO �1/1 �1-3 kVA �ONLINE UPS
USER MANUAL
c. 3ΚVA S(T) (DC24V)
①AC input socket ⑤EPO (Emergency Power Off) port
②Battery connector ⑥RS232 port
③Fan ⑦Intelligent slot
④USB port ⑧Output sockets
Note:
The figure is for reference only. Due to the technology upgrading and development,
the real unit might be different from the figure.

7
NEOLINE PRO �1/1 �1-3 kVA �ONLINE UPS
USER MANUAL
3 Installation
3.1 Unpacking inspection
Open the UPS package and inspect the contents upon receipt. The accessories
attached to the UPS contain a power cord, a user manual, communication cable,
CD-ROM. The long backup model also includes the cable for connection to battery
bank.
Check if the unit is damaged during transport. Do not power on and notify the carrier
and dealer if find damaged or parts missing.
Verify this unit is the model you want to buy. Check the model name showed both
on the front panel and rear panel.
Note:
Keep the packaging box and packaging materials for future transport use. The
equipment is heavy. Always handleit with care.
3.2 Installation information
The UPS installation environment must be in good ventilation, away from water,
flammable gases and corrosive entities.
Do not lie down the UPS against the wall so that front and side panel air intake hole,
rear panel air outtake hole will be unobstructed.
The ambient temperature around the UPS should be within 0℃~40℃（non-
condensing）.
If dismantling the machine at low temperatures, there may be condensation droplets,
users can not install or operate it before UPS completely got dry both inside and
outside, otherwise there will be danger of electric shocks.
Place the UPS near the mains source so that can cut off utility power without any
delay in case of emergency.
Make sure the load connected to the UPS is off when users connect it to UPS, and
then turn on the load one by one later.
Connect the UPS with the power outlet which is over-current protected. Do not
connect the UPS with power outlets whose rated current is less than the maximum
input current of this UPS.
All power outlets should be configured with earthing device for safety.
UPS could be electrified or powered no matter the input power cord is tied or not,
even when the UPS is off. The only way to cut off the output is switching off the UPS
and disconnecting the mains power supply.

8www.tescom-ups.gr
NEOLINE PRO �1/1 �1-3 kVA �ONLINE UPS
USER MANUAL
For all standard model UPS, it is advised to charge the batteries over 8 hours before
using. Once the AC mains power energizes the UPS, it will automatically charge the
batteries. Without prior charging, UPS output remains as usual but with shorter
back-up time than normal.
When connected to motor, display equipment, laser printer etc., UPS power
selection should be based on the startup power of the load which is usually twice
as rated power.
Wiring by a qualified electrician is required. Ensure input cables and output cables
are connected correctly and firmly.
If install a leakage current protective switch, please install it on output cable.
3.3 Installation and output connection
Normally, output connection of 1~3kVA series is configured with power outlets or
terminal blocks, users can plug the load cable into the UPS power outlets to energize
the load. Make sure the mains cable and breakers in the building are enough for the
rated capacity of UPS to avoid the hazards of electric shock or fire.
4 Network Functions
4.1 Communication port
Users could monitor the UPS system through the communication port such as standard
RS232 port and USB port with computer. Connecting this UPS with computer by
communication cable could achieve UPS management easily.
>RS232 port：
：
Pins 1 2 3 4 5 6 7 8 9
Indication empty send receive empty ground empty empty empty empty
Note:
RS232 interface is set as below:
Bit rate: 2400 bps
Byte: 8bit
Completion code: 1 bit
Bit pattern: None

9
NEOLINE PRO �1/1 �1-3 kVA �ONLINE UPS
USER MANUAL
Pins 1 2 3 4
Indication +5V date+ date- GND
>USB port：
：
4.2 EPO port（optional）
EPO is the short for Emergency Power Off. EPO port is
on the rear panel of the UPS. It’s green. Users can cut
off the output of UPS immediately by operating EPO
port in case of emergency.
Normally, pin1 and pin2 are connected so that the machine can be working normally.
When some emergencies happen, and when users have to cut off the output, just need
to disconnect the connection between pin1 and pin2, or just pulling it out.
4.3 Intelligent card (optional)
There is an intelligent slot on the rear panel of the UPS, it’s for SNMP card and dry
contacts. Users can insert any type intelligent card from those three into it to monitor
and manage the UPS. And users don’t have to turn off the UPS when install the
intelligent card. Follow below process:
First of all, remove the intelligent slot cover;
Then insert the intelligent card (SNMP card and dry contacts);
Finally, screw the intelligent card back.
> SNMP card (optional)
SNMP card on UPS is compatible with the most software, hardware and network
operating system, it is a network management of UPS, with this function, UPS can
login on internet , which can supply information of UPS status and input power, and
even possible to control UPS via net management system.
> Dry contacts card (optional)
Insert the dry contacts card into the intelligent slot. It’s another type function of
intelligent monitoring.

10 www.tescom-ups.gr
NEOLINE PRO �1/1 �1-3 kVA �ONLINE UPS
USER MANUAL
5 Operation
5.1 Button operation
Button Function
“ON” key
( +
)
Press the two keys for more than half a second to turn on the UPS.
“OFF” key
(
+
)
Press the two keys for more than half a second to turn off the UPS.
TEST/MUTE key
( + )
Press the two keys for more than 1 second in Line mode or ECO mode or
CUCF mode: UPS runs the self-test function.
Press the two keys for more than 1 second in battery mode: UPS runs the
mute function.
INQUIRING key
( , )
Not in setting mode:
Press or for more than half a second (less than 2 seconds):
display the items orderly.
Press for more than 2 seconds: Circularly and orderly display the
items every 2 seconds, when press the key for some time again, it will
turn to output status.
In setting mode:
Press or for more than half a second (less than 2 seconds):
Select the setting option.
Position
Definition
PIN1 ON：UPS is malfunctioning
PIN2
ON
：
Alarm
（
system failure
）
PIN3 Ground
PIN4
Remote shutdown
PIN5
Common
PIN6 ON：Bypass mode
PIN7
ON
：
Battery low
PIN8 ON：Inverter mode；
OFF
：
Bypass mode
PIN9
ON
：
No AC power in

11
NEOLINE PRO �1/1 �1-3 kVA �ONLINE UPS
USER MANUAL
FUNCTION
SETTINGS key
( )
Not in setting mode:
Press the key for more than 2 seconds: Function settings interface.
In setting mode:
Press the key for more than half a second (less than 2 seconds): go to
the function setting options.
Press the key for more than 2 seconds: exit from this function settings
interface.
5.2 Display interface
Icon display
UPS status information
Operation mode
Display Function
Icon display
Load icon: The approximate load capacity percentage (0-25%, 26-50%, 51-
75% and 76-100%) is indicated by the number of load bar sections
illuminated. When UPS is overloaded, the load icon will flash.
Mute icon: Indicates the audible alarm is disabled / mute.
Press the mute key in the battery mode, the mute icon flash.
Fan icon: Indicates fan working status. When the fan normally runs, the icon
displays rotation; if the fan is not connected or faulty, the icon will flash.
Fault icon: Indicates UPS is in fault mode.
Battery status icon: Indicates the battery capacity of 0-25%, 26-50%, 51-
75%, and 76-100%. When the capacity of battery get low or battery
disconnected, the battery status icon will flash.
UPS status information
In non-setting mode, it displays UPS output information when UPS
normally runs; Fault code will be told in fault mode.
In setting mode, users could adjust different output voltage, activate ECO
mode, activate CUCF mode, select an ID number and so on by operating
function setting keys and inquiring key.

12 www.tescom-ups.gr
NEOLINE PRO �1/1 �1-3 kVA �ONLINE UPS
USER MANUAL
Operation mode
Indicates the power capacity of UPS within 20 seconds after starting up.
Indicates UPS operation mode in 20 seconds, such as STDBY (standby
mode), BYPASS (Bypass mode), LINE (AC mode), BAT (Battery mode),
BATT (Battery Self Test mode), ECO (Economic mode), SHUTDN
(Shutdown mode), CUCF (Constant Voltage and Constant Frequency
mode).
LED indicator light functions
They are respectively inverter light and fault light from left to right.
The inverter light (green LED indicator light) illuminates continuously: it
indicates that UPS is in mains mode or ECO mode or power supply status in
battery mode.
The fault light (red LED indicator light) illuminates continuously: it indicates
that UPS is in fault status.
Note: For LED indication in different modes, please refer to LED/display
panel and alarm list.
5.3 UPS On/Off operation
Operation Description
Turn on the UPS
> Turn on the UPS with mains power
With mains power connected, UPS works in bypass mode, its output is same
as the input voltage within the input range. If there is no need of output voltage
when mains power connected, you can set up bPS to ‘OFF’. Default bPS is
ON, it means there is bypass output when power on.
Press the ON key for more than half a second to start the UPS, then it will start
the inverter.
Once started, the UPS will perform a self-test function. When the self-test
finishes, it will turn to online mode.
> Turn on the UPS by battery without mains power
When main power is disconnected, press the ON key for more than half a
second to start UPS.
The operation of UPS startup process is almost same as above process with
mains power. After the self-test finishes, UPS will work in battery mode.
Turn off the UPS
> Turn off the UPS in Line mode
Press the OFF key for more than half a second to turn off the UPS.
After UPS shutdown, there is no output. If output is needed, you can set BPS
‘ON’ on LCD setting menu.
> Turn off the UPS in battery mode without mains power
Press the OFF key for more than half a second to turn off the UPS.
When UPS shut down, it will do self-test first, until there is no display on the
panel.
UPS self- When UPS is in LINE Mode, press the self-test/mute key for more than 1

13
NEOLINE PRO �1/1 �1-3 kVA �ONLINE UPS
USER MANUAL
test/mute test
operation
second. UPS gets to self-test mode and tests its status. It will exit automatically
after finishing test.
When UPS is in BAT Mode, press the self-test/mute key for more than 1
second, the buzzer stops beeping. If you press the self-test/mute key for one
more second, it will restart to beep again.
UPS Setting
Enter Setup interface. Press and hold the function setting key for more
than 2 seconds, then come to Setup interface, press and hold the inquiring key
( , ) for more than half a second (less than 2 seconds), select the
function setting, choose the setup interface, at the moment, the letters flash.
Enter the setup interface. Press and hold the function setting key for
more than half a second (less than 2 seconds), then come to the setup
interface, at this time, the letters doesn’t flash any more, the numerical value
flash. Press and hold the inquiring key ( , ) for more than half a
second (less than 2 seconds), select the numerical value in accordance with
the function.
Confirm the setup interface. After selecting numerical value, press and hold
the function setting for more than half a second (less than 2 seconds).
Now, the setting function is completed and the numerical value illuminates
without flashing.
Exit from the setup interface. Press and hold function setting key for
more than half a second (less than 2 seconds), exit from the setup interface
and return to the main interface.
Note:
UPS could not be set until it is connected to the battery and it is turned off and
switched to Stdby mode (standby mode).
Disconnect mains power after setting.
The LCD display screen will automatically extinguish in about 1 min, and the
setting will be configured normally.
5.4 UPS Settings
Output voltage setting
LCD display Settings
For 208/220/230/240 VAC models, you may choose the
following output voltage:
208: output voltage is 208Vac
220: output voltage is 220Vac
230 (default): output voltage is 230Vac
240: output voltage is 240Vac

14 www.tescom-ups.gr
NEOLINE PRO �1/1 �1-3 kVA �ONLINE UPS
USER MANUAL
Low voltage of battery setting
LCD display Settings
The battery voltage selecting interface. You may choose the
following output voltage:
9.8: Low voltage of battery is 9.8Vdc
9.9: Low voltage of battery is 9.9Vdc
10: Low voltage of battery is 10Vdc
10.2: Low voltage of battery is 10.2Vdc
10.5: Low voltage of battery is 10.5Vdc
dEF (default): EOD voltage automatically varies with loads,
including 20 hours discharge protection
Bypass mode setting
LCD display Settings
Enable or disable Bypass function. You may choose the
following two options:
ON: Bypass enable
OFF (default): Bypass disable
AUO setting
LCD display Setting
AUO setting only can be set in Stdby mode or Bypass
mode. You may choose the following two options:
ON: UPS will start up automatically and works in Line mode
when connect mains.
OFF (Default): UPS won’t start up automatically when
connect mains except EOD, it will work in standby or bypass
mode.
5.5 Parameters inquiring operation
Press the inquiring key or for more than half a second (less than 2 seconds)
to inquire about items. The inquired items include Input, Battery, Output, Load and
Temperature. The displayed items on LCD screen are shown as following:

15
NEOLINE PRO �1/1 �1-3 kVA �ONLINE UPS
USER MANUAL
LCD display Description
Output：
：
Display the output voltage and output frequency
of the UPS. As the following graphic shows, the output
voltage is 220V, the output frequency is 50Hz.
Load: Display the numerical value of the active power
(WATT) and apparent power (VA) of the load. For example,
as the following graphics shows, the WATT of the load is
800W, VA is 1.0kVA (when disconnect loads, it is a normal
phenomenon to show a small numerical value of WATT and
VA).
Version and Temperature: Indicate firmware version of
UPS and display the highest temperature of UPS
components; As the following graphics shows, the firmware
version is v1.7, the maximum temperature is 40℃.
Input: Display the voltage and frequency of the input. As
the following graphics shows, the input voltage is 220V,
input frequency is 50Hz.
Battery: Display the voltage and capacity of the battery. As
the following graphics shows, the battery voltage is 24V, the
capacity of battery is 100% (the capacity of battery is
approximately reckoned according to the battery voltage).
Warning: Display the warning code.

16 www.tescom-ups.gr
NEOLINE PRO �1/1 �1-3 kVA �ONLINE UPS
USER MANUAL
5.6 Operation mode
Operation mode and LCD display Description
Bypass mode
Turn to bypass mode under the following three conditions:
Connect mains power and the bypass setup is ON.
Turn off the UPS in line mode and the bypass setup is
ON.
Overload in line mode.
Note: When UPS is working in bypass mode, it has no back
up function.
Line mode
Being in line mode are as following: When input mains
corresponding to the working conditions, UPS will work in
line mode, LCD displays ‘Line’.
Stdby mode
UPS is powered off and no output supply power, but still
can charge batteries.
Battery mode
Being in battery mode are as following: the buzzer beeps
once every 4 seconds.
When the mains power is low or unstable, UPS will turn to
battery mode at once, and LCD displays ‘batt’.

17
NEOLINE PRO �1/1 �1-3 kVA �ONLINE UPS
USER MANUAL
ECO mode
Being in ECO mode are as following: When the input
mains meet the input range of the ECO mode and the
ECO function is on, the UPS works in ECO mode. If input
mains exceed the range of ECO several times within one
minute but stays in inverter input range, UPS will work in
inverting mode automatically. LCD displays ‘ECO’.
CUCF mode
Frequency conversion mode is mainly to provide a stable
voltage and frequency (mainly in terms of frequency). After
starting this mode, its output will not be affected by utility
to meet input needs of some precision equipment and
make users’ load more stable and secure. After opening
CUCF mode setup, LCD displays ‘CUCF’. In CUCF mode,
the loading capacity will drop to 70% of the original
capacity. The output frequency is fixed at the setting
value, it doesn’t vary with utility change. And the UPS
cannot be set to bypass mode in this mode.
Fault mode
When UPS has a failure, the buzzer beeps and the UPS
turns to fault mode. UPS cuts off the output and LCD
displays fault codes. At the moment, users can press the
mute key to make the buzzer stop beeping temporarily to
wait for maintenance. Users can also press the OFF key to
shut down the UPS when confirm that there is no serious
fault.
6 Fault Messages
Table 1: Fault code messages
Fault code Fault type Bypass output Note
0、1、2、3、4 Bus high yes
5、6、7、8、9 Bus low yes
10、11、12、13、14 Bus unbalance yes
15、16、17、18、19 Bus soft start fail yes
20、21、22、23、24 Inverter soft start fail yes
25、26、27、28、29 Inverter high yes
30、31、32、33、34 Inverter low yes

18 www.tescom-ups.gr
NEOLINE PRO �1/1 �1-3 kVA �ONLINE UPS
USER MANUAL
35、36、37、38、39 Bus discharge fail yes
40、41、42、43、44 Over heat yes
45、46、47、48、49 Output short no
50、51、52、53、54 Overload yes
55、56、57、58、59 Bus short yes
60、61、62、63、64 Shutdown fault yes
70、71、72、73、74 Overload 5 times yes
Table 2: Working status messages
S/
N
Working status
LCD display
messages
Alarm
beep
LCD
flashes
LED flashes
Invert
er
Fault
1
Inverter mode (mains power)
Mains power
voltage
Working mode displays
Line
No beep No flash
Flash
always
/
Mains power
high/low voltage
protection, switch
to battery mode
Working mode displays
bAT
One
beep / 4
sec
One
flash / 4
sec
One
flash /
sec
/
2 Battery mode
Battery voltage -
normal
Working mode displays
bAT
One
beep / 4
sec
One
flash
/ 4 sec
One
flash /
sec
/
Warning for
abnormal voltage
of battery
Working mode displays
bAT, Bat flash
One
beep /
sec
One
flash
/ sec
One
flash /
sec
/
3
Bypass mode
Mains power –
normal（under
Bypass
）
Working mode displays
byPASS
One beep
/ 2 min
No flash
One
flash /2
sec
/
4
Warning for battery disconnected
Bypass mode
Working mode displays
byPASS, bat display is
0, and flash all the time
One
beep / 4
sec
One
flash
/ 4 sec
One
flash /2
sec
/
Inverter mode
Working mode displays
Line, bat display is 0,
and flash all the time
One
beep / 4
sec
One
flash
/ 4 sec
Flash
always
/
Power on / Switch
on
LCD illuminates when
power on, and display
the capacity of the UPS,
later working mode
displays Line or
byPASS, bat icon flash
all the time
6 beeps
Flash
always
Flash
always
Flash
always
/ /
5
Output overload protection
Warning for mains
power overload
Working mode
displays Line, load
2 beeps /
sec
2
flashes
Flash
always
/