Thane Fitness BikeNook GO User manual

Assembly Instructions
Bicycle Stand

2 3
ASSEMBLY INSTRUCTIONSTHANK YOU
1. Press the Spring Ball Lock Pin (10) on the
center-right side of the Bracket (4) and move
the Right Female Telescopic Tube (6) to Open
position (far-right) until the Spring Ball Lock
Pin (10) pops out.
2. Loosen the Ribbed Ring of the Telescopic
Tube Locking Mechanism (9) by turning it in a
counterclockwise direction until some threads
are exposed (approximately two full turns).
3. Take one Male Telescopic Tube (8), align
grooves on the Male and Female tubes and
insert the Male Telescopic Tube (8) through
the Ribbed Ring of the Telescopic Tube
Locking Mechanism (9) into the Right Female
Telescopic Tube (6).
Important: Size Marks on the Male Telescopic
Tube (8) should be facing up and the side
with the Size Mark 12 is inserted into the
Female Telescopic Tube (6,7).
4. Loosely tighten the Ribbed Ring of the
Telescopic Tube Locking Mechanism (9) by
turning it in a clockwise direction.
Repeat steps 2 - 4 on the left side.
Congratulations on your choice of the Bike Nook™ GO bicycle stand, the brilliant new
way to store your bike away, quickly and easily.
The Bike Nook™ GO bicycle stand is as easy as 1-2-3 and saves up to 3.5 ft/1 m of
valuable floor space. The best part is that it easily adjusts to accommodate all kinds of
bikes, including mountain bikes, road bikes, racers, beach bikes, kids’ bikes, wheel size
16 in/41 cm and up, and even some e-bikes*.
Please use these easy to follow instructions for tips on how to set up your Bike Nook™
GO and use it for different sizes of bikes. We hope you enjoy the quick and easy new
way to store your bicycle, and all of the free space you get back!
Thane Direct and its affiliated companies assume no liability for personal injury or
property damage resulting from the misuse of the Bike Nook™ GO bicycle stand
including the failure to comply with the instructions contained in this User’s Guide.
*NOTE: The Bike Nook™ GO bicycle stand can be used for some e-bikes, but only if
they are equipped with a conventional bike seat and seat post and if e-bikes do not
weight more than 66 lb/30 kg. E-bikes with a scooter-type seat are not compatible as
they do not have a seat post that the Bike Nook™ GO Clamps can be attached to.
PARTS LIST
1. Front Clamp
2. Back Clamp with Receptor Tube
3. Long Bolts
4. Bracket
5. Finger Bolt
6. Right Female Telescopic Tube
7. Left Female Telescopic Tube
8. Male Telescopic Tubes
9. Telescopic Tube Locking Mechanism
with Ribbed Ring
10. Spring Ball Lock Pins
11. Spacer
12. Allen Key
13. Wheel Strap
1
2
3
12
5
98
76
10
4
11
13

4 5
ASSEMBLY INSTRUCTIONSASSEMBLY INSTRUCTIONS
5. Press the Spring Ball Lock Pin (10) on the
far-right side of the Bracket (4) and move
the Right Female Telescopic Tube (6) and the
Male Telescopic Tube (8) Assembly to Closed
position (center-right) until the Spring Ball
Lock Pin (10) pops out.
6. Place the Front Clamp (1) and Back Clamp with Receptor Tube (2) around your
bike’s Seat Post, below the seat.
Note: The Front Clamp (1) must be placed facing the front of the bike; the Back
Clamp with Receptor Tube (2) must be positioned facing the back of the bike. The
Back Clamp with Receptor Tube (2) must be positioned with the threaded hole for
the Finger Bolt (5) on right side of the bike.
7. Insert the Long Bolts (3) first through the Front Clamp (1) holes, then screw into
threaded holes on the Back Clamp with Receptor Tube (2).
8. Tighten the Long Bolts (3) using the Allen Key (12).
Note: Do not yet fully tighten the Long Bolts (3) holding the Front Clamp (1)
and the Back Clamp with Receptor Tube (2) onto the Seat Post - this takes
place only in step 12 further below.
9. Make sure that the Spacer (11) is fitted
on the square tube of the Bracket (4).
Important: Tighten the Long Bolts (3)
evenly switching between tightening the
two bolts. When tightening, ensure that
the Front Clamp (1) and Back Clamp
with Receptor Tube (2) are parallel to
one another and the gaps between the
Front Clamp (1) and the Back Clamp with
Receptor Tube (2), on both sides, are even.
10. Attach the Bracket (4) / Telescopic Tubes (6,7,8) Assembly to the Back
Clamp with Receptor Tube (2). Align the hole on the Bracket (4) with the
threaded hole on the Back Clamp with Receptor Tube (2). Screw the Finger
Bolt (5) until tight.
11. Ensure that the Back Clamp with Receptor Tube (2) / Bracket (4) /
Telescopic Tubes (6,7,8) Assembly is aligned directly over the back wheel of
the bike.
䘠
×
×

6 7
ASSEMBLY INSTRUCTIONS SET LENGTH OF TELESCOPIC TUBES
12. Fully tighten the Long Bolts (3) on the Front Clamp (1).
Once tightened, there may be a gap between the Front Clamp (1) and Back
Clamp with Receptor Tube (2). This is acceptable and the gap may vary
depending on the width of the bike seat post.
Assembly is completed.
As the size of bikes varies, the length of the Telescopic Tubes must be varied
to safely and securely store the bike.
1. Press the Spring Ball Lock Pin (10) on the center-right side of the Bracket
(4) and move the Right Female Telescopic Tube (6) and the Male Telescopic
Tube (8) Assembly to Open position (far-right) until the Spring Ball Lock Pin
(10) pops out.
2. Press the Spring Ball Lock Pin (10) on the center-left side of the Bracket (4)
and move the Left Female Telescopic Tube (7) and the Male telescopic tube
(8) assembly to Open position (far-left) until the Spring Ball Lock Pin (10)
pops out.
3. Determine the length of the Telescopic Tubes (6,7,8) by pushing the bike
with the back wheel perpendicular against a wall or door.
Important: Do NOT exceed the manufacturer’s
maximum recommended torque for your bike
seat post when tightening the clamp.
Overtightening may damage the seat post.

8 9
SET LENGTH OF TELESCOPIC TUBES STORE YOUR BIKE VERTICALLY
4. Pull out the Male Telescopic Tubes (8) until they touch the wall or door.
Note: Make sure that Male Telescopic Tubes (8) are evenly extended. This is
the “set” length for the telescopic Tubes.
Note: For your convenience the Male Telescopic Tubes (8) have marks from 1
to 12 to help you to remember how far the Male Telescopic Tubes (8) should
be extended for future reference.
To store your bike, use the Bike Nook™ GO on a solid, level and flat surface.
Note: Make sure that the Left and Right Female Telescopic Tube (6) and the
Male Telescopic Tube (8) Assembly are in their Open positions and Male
Telescopic Tubes (8) are evenly extended to the "set" length.
3. Lift the front wheel of the bike and rotate until both Telescopic Tubes (6,7,8)
contact the floor.
Once your bike is in the storage position, check that it stands stable and
secure.
4. With both Telescopic Tubes (6,7,8) fully locked and evenly in contact with
the floor, this is the vertical storing position of your bike.
1. Attach the Wheel Strap (13) around
the front wheel of the bike and around
the bike frame. This will prevent the
wheel from moving and causing
instability when storing the bike.
2. Hold your bike by the seat and
handles.
5. Lock the Telescopic Tube Locking
Mechanism (9) on both sides by
turning the Ribbed Rings clockwise
until fully tightened.
Important: When the Telescopic
Tube Locking Mechanism (9) is fully
tightened the Lock Mark Line under
the Ribbed Ring of the Telescopic Tube
Locking Mechanism (9) is covered. If
the Lock Mark Line is completely visible
it means that the Telescopic Tube is
not fully tightened and you should
turn/tighten the Ribbed Ring of the
Telescopic Tube Locking Mechanism
(9) further until the Lock Mark Line is
fully covered.
Important: If the Long Bolts (3), Spring Ball Locking Pins (10) and Telescopic
Tube Locking Mechanisms (9) are not tightened/locked properly the structure
may collapse which can cause your bike to fall.
✓
X

10 11
FROM STORING TO USING YOUR BIKE DETACHING THE BRACKET AND TELESCOPIC TUBES
ASSEMBLY FROM YOUR BIKE
When you want to detach the Bracket (4) and Telescopic Tubes (6,7,8,9)
Assembly from the Back Clamp with Receptor Tube (2) on your bike.
1. Unscrew the Finger Bolt (5) located on the right side of the Back Clamp (2).
2. Grasp the Spacer (11) with one hand and slide the Bracket (4) and
Telescopic Tubes (6,7,8) Assembly out using the other hand.
Note: The Spacer (11) should remain attached to the Bracket (4).
Note: When storing the Bracket (4) and Telescopic Tubes (6,7,8) Assembly,
it is suggested to screw the Finger Bolt (5) into the threaded hole on the
Bracket (4) to compactly store the Bracket (4) and Telescopic Tubes (6,7,8)
Assembly for future use.
Note: The Front Clamp (1) and Back Clamp with Receptor Tube (2) should
remain connected to the Seat Post for future use.
3. Release the Wheel Strap (13).
Your bike is now ready to use.
2. Unlock the Telescopic Tube Locking Mechanism (9) on both sides by
turning it counterclockwise. Push in both Male Telescopic Tubes (8) in until
they stop. Lock the Telescopic Tube Locking Mechanism (9) on both sides by
turning it clockwise.
3. Press the Spring Ball Lock Pin (10) on the far-right side of the Bracket (4)
and move the Right Female Telescopic Tube (6) and the Male Telescopic Tube
(8) Assembly to Closed position (center-right) until the Spring Ball Lock Pin
(10) pops out.
4. Press the Spring Ball Lock Pin (10) on the far-left side of the Bracket (4)
and move the Left Female Telescopic Tube (7) the Male Telescopic Tube (8)
Assembly to Closed position (center-left) until the Spring Ball Lock Pin (10)
pops out.
Your bike is ready when you want to keep the Bracket (4) and Telescopic Tubes
(6,7,8) Assembly attached to your bike.
1. To change from storing the bike vertically to riding it, rotate it from its storing
position and lower the front wheel to the floor.

12 13
OPTIONAL ITEMS OPTIONAL ITEMS
CARGO RACK
HOW TO ATTACH
1. Remove the round black sticker from the Right Female Telescopic Tube (6).
2. Align the center of the front Clamping Support located at the bottom of
the Cargo Rack with the hole on the Right Female Telescopic Tube (6).
3. Firmly push both clamping supports (front and back) of the cargo rack onto
the Right Female Telescopic Tube (6) until it locks in.
Important: MAX load weight for the Cargo Rack is 7.7 lb/3.5 kg. Make sure to
secure items on the cargo rack with any suitable straps.
TAIL LIGHT
HOW TO ATTACH
1. Put the lower side of the Elastic Rubber Band over the lower hooks on the
Taillight.
2. Take the upper side of the Elastic Rubber Band and push it halfway one
side through the oval hole located at the back of the Cargo Rack.
3. Put the upper side of the Elastic Rubber Band over the upper hooks on the
Taillight.

BikeNookGO MNL ENG R0 230614
Distributed by:
Thane USA, Inc., 4050 Whipple Ave. NW, #31, Canton, OH 44718, U.S.A.
Thane Canada Inc., 2680 Skymark Avenue, Unit 110, Mississauga ON L4W 5L6, Canada
Thane Direct UK Limited, 3 Acorn Business Centre, Northarbour Road, Portsmouth, PO6 3TH
Danoz Direct Pty Ltd. Bondi Junction, NSW, 2022, Australia
TVINS Scandinavia AB, SE-211 34 Malmö, Sweden
© 2023 Thane IP Limited.
MADE IN CHINA
“Thane”, “Bike Nook”, and related logos and variations are trademarks or registered trademarks, in
Canada and/or other countries, of Thane IP Limited and/or its affiliated companies.