Thane Fitness BikeNook Turbo Quick setup guide

Assembly and Use
Instructions
Bicycle Stand

THANK YOU CONTENTS
Congratulations on your choice of the Bike Nook™ Turbo bicycle stand, the
brilliant new way to store your bike away, quickly and easily.
The Bike Nook™ Turbo bicycle stand is as easy as 1-2-3 and saves up to 3.5 feet (1 meter) of
valuable floor space. The best part is that it easily adjusts to accommodate all kinds of bikes,
including mountain bikes, road bikes, racers, beach bikes, kids’ bikes, wheel size 16in/40cm
and up, and even some e-bikes*.
Please use these easy to follow instructions for tips on how to set up your Bike Nook™ Turbo
and use it for different sizes of bikes.
We hope you enjoy the quick and easy new way to store your bicycle, and all of the free space
you get back!
Thane Direct and its affiliated companies assume no liability for personal injury or property
damage resulting from the misuse of the Bike Nook™ Turbo bicycle stand including the fail-
ure to comply with the instructions contained in this User’s Guide.
*NOTE: The Bike Nook™ Turbo bicycle stand can be used for some e-bikes, but only if they
are equipped with a conventional bike seat and seat post. E-bikes with a scooter-type seat
are not compatible as they do not have a seat post that the Bike Nook™ Turbo Clamp can be
attached to.
A. Parts, Tools, Bolts & Nuts ........................................................................................................... 4
B. Summary of Assembly Steps.....................................................................................................5
C. Assembled Bike Nook™ Turbo...................................................................................................6
D. Detail Assembly Instructions.......................................................................................................7
1. Connect Clamp to Seat Post ............................................................................................................................. 7
2. Connect Adjustment Tube to Clamp Receptor...........................................................................................8
3. Connect Base Pipe to Support Tube Bracket............................................................................................... 9
4. Set length of Adjustment Tube & connect to Support Tube...................................................................10
E. Use Instructions ...............................................................................................................................11
1. Preparing to store your bike ................................................................................................................................11
2. Storing your bike vertically ................................................................................................................................... 12
3. From storing to using your bike......................................................................................................................... 13

4 5
B. SUMMARY OF ASSEMBLY STEPS
(For more information, see section D. Detail Assembly Instructions)
A. PARTS, TOOLS, BOLTS & NUTS FOR ASSEMBLY
Assembly Steps:
1. Connect Clamp (3) to Seat Post.
Use: Long Bolts (22) Washers (23) &
Nut (24). Tighten with: Allen Key (27).
IMPORTANT! Do NOT overtighten
the Clamp (3). See next page for
correct Clamp (3) assembly.
2. Connect Adjustment Tube (10)
to Clamp Receptor (7).
Insert Finger Bolt (9) through
Receptor Hole (8) (underneath
Clamp Receptor 7), and screw into
Threaded Hole (11) (on Adjustment
Tube (10)), until tight.
3. See below
4. Set length of Adjustment Tube
(10) & connect to Support Tube (17).
Use: Short Bolts (26) & Nuts (24)
Tighten with: Allen Key (27) & Hex
Wrench (28).
3. Connect Base Pipe (15) to
Support Tube Bracket (18).
Use: Medium Bolts (25) & Nuts (24)
Tighten with Allen Key (27) & Hex
Wrench (28).
Parts
1. Front Clamp
2. Back Clamp
3. Clamp (Front & Back)
4. Front Clamp Hole (x2)
5. Back Clamp Hole (x2)
6. Hexagon Cavity (x2)
7. Clamp Receptor
8. Receptor Hole
9. Finger Bolt
10. Adjustment Tube
11. Threaded Hole
12. Adjustment Holes
13. Female Base Pipe
14. Male Base Pipe
15. Base Pipe (Female + Male)
16. Pipe End Cap
17. Support Tube
18. Support Tube Bracket
19. Support Tube Large Holes (x2)
20. Support Tube Small Holes (x2)
21. Wheel Strap
Tools, Bolts & Nuts
22. M6 x 40mm Bolt (x2) (Long)
23. M6 Washer (x2)
24. M6 Nut (x6)
25. M6 x 37mm Bolt (x2) (Medium)
26. M6 x 30mm Bolt (x2) (Short)
27. Allen Key
28. Hex Wrench
3
1
Seat Post
Bike Seat
2
8, 9, 11
7
10
10
17
Bike Nook™ Turbo
connected to seat post
18
13 14
15
9. Finger Bolt
22. M6 x 40mm
Bolt (x2) (Long)
23. M6 Washer (x2)
24. M6 Nut (x2)
25. M6 x 37mm
Bolt (x2) (Medium)
24. M6 Nut (x2)
26. M6 x 30mm
Bolt (x2) (Short)
24. M6 Nut (x2)
27. Allen Key
28. Hex Wrench
Long Medium Short
1
4
4
22 22
3
23 23
24
5
2
78 (Underneath)
11 (Underneath)
21
17
26
26
25
14
24
24
24
24 25
18
15
16
5
12
10
66
24
9
20 19
19
20
16 27 28 13

6 7
C. ASSEMBLED BIKE NOOK™ TURBO
Seat Post
1. Front Clamp
2. Back Clamp
7. Clamp Receptor
9. Finger Bolt
IMPORTANT NOTE: When connecting the Bike Nook™
Turbo Front Clamp (1) and Back Clamp (2) to the bike seat
post, tighten the Nuts (24), Washers (23) and Long Bolts
(22) until the Clamp (3) is securely fastened to the seat
post, with equal gaps between the Front Clamp (1) and
Back Clamp (2) on both sides. See section D for detailed
instructions on proper Clamp (3) assembly.
Do NOT overtighten the Nuts and Bolts as this may result in breaking of the Clamp (3).
Once tightened, there may be a gap between the Front Clamp (1) and Back Clamp (2). This is acceptable
and the gap may vary depending on the width of the bike seat post.
10. Adjustment Tube
15. Base Pipe
17. Support Tube
3. Clamp
1
2
9
10
17
15
7
3
1. Connect Clamp to Seat Post
1. Place the Front Clamp (1)
and Back Clamp (2) around
your bike’s Seat Post, below the
seat.
Note:
• The Front Clamp (1) must be
placed facing the front of the
bike; the Back Clamp (2) must
be positioned facing the back
of the bike.
• The Back Clamp (2) must be
positioned with the Receptor
Hole (8) (underneath the
Clamp Receptor (7)), facing
downwards.
4. To secure the Front Clamp
(1) and Back Clamp (2) to the
Saddle Post, push and hold
the Nuts (24) into the Hexagon
Cavities (6) and tighten the
Long Bolts (22) using the Allen
Key (27).
2. Insert the Long Bolts (22)
with Washers (23), first
through the Front Clamp
Holes (4), then through the
Back Clamp Holes (5).
Note:
The Washers (23) must
be located against the Front
Clamp Holes (4).
5. Important: Tighten the Long
Bolts (22) evenly switching
between tightening the two
bolts. When tightening, ensure
that the Front Clamp (1) and
Back Clamp (2) are parallel
to one another and the gaps
between the Front Clamp (1)
and the Back Clamp (2), on
both sides, are even.
3. Hand screw the Nuts (24)
onto the protruding Long Bolt
(22).
6. Note: Do not yet fully
tighten the Long Bolts (22)
holding the Front Clamp (1)
and the Back Clamp (2) onto
the Seat Post - this takes
place only in Section 4, Step
6 further below.
7
1
8
2
1
4
2
5
3
6
524 22
4
22,
23
27
22
22 22
1
11
2
222
22
2
6
24
D. DETAIL ASSEMBLY INSTRUCTIONS
!WARNING
Seat Post
Equal Gaps
1
3
2

2
8
2. Connect Adjustment Tube to Clamp Receptor & Tighten Finger Bolt
1. Find the Threaded Hole (11)
on the one end of the
Adjustment Tube (10).
4. Insert the Finger Bolt (9)
through the Receptor Hole (8),
on the underside of the Clamp
Receptor (7), and onto the
Threaded Hole (11).
2. Turn the Adjustment Tube
(10) so that the Threaded Hole
(11) is on the underside.
5. Screw the Finger Bolt (9)
into the Threaded Hole (11)
until tight.
6b. If there is misalignment of
the Adjustment Tube (10), slightly
loosen the Clamp (3) Long Bolts
(22) and adjust the Clamp (3)
so that the Adjustment Tube (10)
becomes aligned with the back
wheel of the bike. Slightly
re-tighten the Long Bolts (22).
6c. Fully tightening the Long
Bolts (22) takes place only in
Section 4, Step 6 further below.
3. Fully insert the Adjustment
Tube (10) into the Clamp
Receptor (7) until the Threaded
Hole (11) aligns with the Receptor
Hole (8) on the underside of
the Clamp Receptor (7).
6a. Check that the Adjustment
Tube (10) is aligned directly
over the back wheel of the
bike. Lightly tighten the Long
Bolts (22) on the Clamp (3).
10
10 10
11 (inside)
7 8
99
10
7
11
11
11
8
1
4 5 6a
10
7
22
3
10
10
6
Mis-aligned Adjustment
Tube (10)
9
3. Connect Base Pipe to Support Tube Bracket
1. Align the Female Base Pipe (13)
with the Male Base Pipe (14).
2. Insert the Male Base Pipe (14)
into the Female Base Pipe (13),
together making up the Base Pipe
(15). Check that the holes in the two
Pipes are aligned.
3. Place the Support Tube (17)
perpendicular to the Base Pipe
(15). Slide the Base Pipe (15) into
the Support Tube Bracket (18)
and align the holes in the Base
Pipes (15) with the holes in the
Support Tube Bracket (18).
4. Insert the Medium Bolts (25)
through the holes in the Support Tube
Bracket (18) and the holes in the Base
Pipe (15). Hand screw the Nut (24) onto
the ends of the Medium Bolt (25).
5. Use the Allen Key (27) and Hex
Wrench (28) to tighten the Medium Bolts
(25) and the Nuts (24) to securely connect
the Pipe (15) to the Support Tube (17).
15
17
18
18
24 (underneath)
25
25
24
15
13 14
1
4
2
5
3
27 28
6b 6c
Correct aligned Adjustment
Tube (10)
10
4
3

3
10
4. Set length of Adjustment Tube & connect to Support Tube
As the size of bikes varies, the combined length of the Adjustment Tube (10)
and the Support Tube (16), must be varied to safely and securely store the bike
1. Turn the Support Tube (17) with the two large
Support Tube Holes (19) facing up. Align the
Support Tube (17) with the Adjustment Tube (10).
3. Determine the length of the
Adjustment Tube (10) by pushing
the bike with its back wheel
perpendicular against a wall or
door. Slide the Support Tube (17)
along the Adjustment Tube (10)
until the Base Pipe (15) touches
the wall. This is the “set” length
for the Adjustment Tube (10).
6. Again, check that the Adjustment
Tube (10) and Support Tube (17)
called the “T Bar” is aligned directly
over the back wheel of the bike. If
not, slightly unscrew the Long Bolts
(22) of the Clamp (3) and adjust
the Clamp (3) for correct alignment
of the T Bar. Once aligned, firmly
tighten the Long Bolts (22) on
Clamp (3), leaving equal gaps on
both sides. Do NOT overtighten.
4. Align the Support
Tube Hole (19) with the
Adjustment Holes (12) on
the Adjustment Tube (10).
This may require sliding the
Support Tube (17) slightly
forward or backwards over
the Adjustment Tube (10)
until the Support Tube Holes
(19 & 20) align with the
nearest Adjustment Holes (12).
5. From above the Support
Tube (17), insert the Short Bolt
(26) into the Support Tube
Large Holes (19) and through
the Adjustment Holes (12) in
the Support Tube (10) until they
protrude through the Support
Tube Small Holes (20). Screw on
the Nuts (24) and tighten using
the Allen Key (27) and the Hex
Wrench (28).
2. Slide the Support Tube (17) over the
Adjustment Tube (10).
The above completes assembly
of the Bike Nook™ Turbo
1
4
2
5
3
6
10 10
19 19
17 17
19
12
17 17
17
19
12 (inside)
10
10
10
10
17
Check
T Bar
alignment
11
E. USE INSTRUCTIONS
1. Prepare to store your bike
1. Move your bike to a storing
area. Attach the Wheel Strap
(21) around the front wheel of
the bike and around the bike
frame. This will prevent the
wheel from causing instability
when storing the bike.
2. Insert the Adjustment
Tube (10) (connected to the
Support Tube (17) and the
Base Pipe (15)) fully into the
Clamp Receptor (7). The
Threaded Hole (11) (on the
Adjustment Tube (10)) must
align with the Receptor Hole
(8) on the underside of the
Clamp Receptor (7).
3. Insert the Finger Bolt (9)
through the receptor Hole
(8) on the underside of the
Clamp Receptor (7) and screw
into the Threaded Hole (11)
until tight.
1 2 3
21
15 17
17
3
10
11
17
10
10
9
8
11
78
With the Base Pipe (15) connected to the Support Tube
(17), connected to the Adjustment Tube (10), both aligned
with the back wheel of the bike, and with the Adjustment
Tube (10) inserted and connected to the Clamp Receptor
(7), the Bike Nook™ Turbo is configured to compactly and
horizontally store your bike - see step 2 below.

12
2. Store your bike vertically
To store your bike, use the Bike Nook™ Turbo on a solid, level and flat surface.
1. Hold your bike by the seat
and handles.
2. Lift the front wheel of the
bike and rotate until the Base
Pipe (15) contacts the floor.
Once your bike is in the storage
position, check that it stands stable
and secure
3. With the Base Pipe (15) in
contact with the floor, this is
the vertical storing position of
your bike.
1 2 3
21
3
10
17
15
13
3. From storing to using your bike
1. To change from storing the bike vertically to riding it, rotate it from its storing position and lower
the front wheel to the floor.
2. Unscrew the Finger Bolt (9)
underneath the Clamp
Receptor (7).
3. Slide the Adjustment Tube
(10) out from the Clamp
Receptor (7).
Note
• When storing your Bike Nook™
Pillar, it is suggested to screw
the Finger Bolt (9) into
Threaded Hole (11) on the
Adjustment Tube (10) to
compactly store the “T
section” of your Bike Nook™
Pillar for future use.
• The Clamp (3) must remain
connected to the Saddle Post.
4. Release the Wheel Strap
(21). Your bike is now ready to
ride.
10 9
11
2
1a 1b 1c
34
9
7
7
10
21

Distributed by:
Thane USA, Inc., 4050 Whipple Ave. NW, #31, Canton, OH 44718
Thane Canada Inc., 2680 Skymark Avenue, Unit 110, Mississauga, ON L4W 5L6
Thane Direct UK Limited, 3 Acorn Business Centre, Northarbour Road, Portsmouth, PO6 3TH
Danoz Direct Pty Ltd. Bondi Junction, NSW, 2022, Australia
TVINS Scandinavia AB, SE-211 34 Malmö, Sweden
“Thane”, “Bike Nook”, and related logos and variations are trademarks or registered trademarks,
in Canada and/or other countries, of Thane IP Limited and/or its affiliated companies.
© 2023 Thane IP Limited.
MADE IN CHINA
BikeNook Turbo MNL ENG R2 230217