The Children's Furniture Company Jemima 4 Poster Bed User manual

Adult assembly required
CHOKING HAZARD This item contains small parts that have sharp edges
and may be a choking hazard to children under 3 years old
Adults should take care when unpacking and assembling this item
Keep children away during assembly
BEFORE YOU BEGIN ASSEMBLY
PRE-ASSEMBLY
CARE INSTRUCTIONS
Please read all instructions before starting the assembly.
It is recommended that 2 people assemble this bed.
Save all packing materials until assembly is complete to avoid accidentally
discarding smaller parts and hardware
Assemble this furniture on a protective surface eg carpet in the room it will be
used.
Assemble and use on a flat surface
Please do not use power tools when constructing this piece of furniture
Wipe clean using a soft damp cloth followed by a dry cloth
Do NOT use cleaning products which may contain ammonia, solvents or
abrasive material.
Do NOT expose the furniture to extremes of heat and humidity
Important: Keep these instructions for further use
If any components are missing or damaged, do not commence assembly and
do not use the item. Please contact The Childrens Furniture Company on 0843
289 2646 immediately
PLEASE READ THE IMPORTANT NOTES ON PAGE 2 1
Jemima 4 Poster Bed

IMPORTANT- READ
CAREFULLY-RETAIN FOR
FUTURE REFERENCE
All assembly fastenings should be tightened properly and periodically checked, care
should be taken that no fittings are loose
This child's bed is designed to conform to with BS 8509:2008+A1:2011
This bed is suitable for a mattress size of 90cm (w) x 190cm (l)
This bed is not designed to be dismantled for storage or transportation
Children are likely to play, bounce, jump, and climb on beds, therefore the bed
should not be placed too close to other furniture or windows, blind cords, curtain
pulls, or other strings and cords, and should be placed either tight to any wall or have
a gap of at least 300mm between the wall and the side of the bed
Any additional or replacement parts should only be obtained from The Children's
Furniture Company.
WARNING: Not suitable for children under the age of 4 years.
WARNING: Do not place this child's bed near heat sources,
windows or other furniture.
WARNING: Do not use this bed if any part is broken or missing.
2
Jemima 4 Poster Bed

Carefully unwrap the parts
and check the fittings
B640 M6 x 40mm
4 pieces
BF103 Demi lune washer
8 pieces
BF104 M8 nut
8 pieces
BF105 M8 All thread
8 pieces
Top hat bolt
6 pieces
BTH
C101 15mm cam
4 pieces
C104 Steel dowels
4 pieces
C108 8 x 35 mm
4 pieces
T101 4 mm Allen key
1 piece
T103 Spanner
1 piece
Fittings
Headboard panel
Rear posts
B630 M6 x 30mm
6 pieces
3
Jemima 4 Poster Bed
Front posts
Header/footer rail
Canopy rails
Side rails
Slats

Prepare the Headboard
panel
Prepare the rear posts
1. Insert the dowels (part C108) into
the 4 holes on the edge of the head
board panel. (Tip double check you
don't insert the dowels in holes
connected to the cams)
2. Insert the 4 cams (part C101) into
the holes on the rear face of the
headboard panel.
Note position of
arrow on hardware
C101 15mm cam
4 pieces
C108 8 x 35 mm
4 pieces
BF105 M8 All thread
8 pieces
C104 Steel dowels
4 pieces
3. Repeat on the 2nd rear post
4
Jemima 4 Poster Bed
1. Screw in two steel dowels (part
C104) into the smallest holes on the
rear leg
2. Screw in All thread (part
BF105) into the hole with metal
insert.

Assemble the Headboard
3. Tighten all fittings when assembled
tighten cams by turning
counter clockwise
BF103 Demi lune washer
8 pieces
BF104 M8 nut
8 pieces
Prepare the front posts
Ease the rail over steel
rod, insert the demi lune
washer just before pushing
the rail firmly into place
BF103 Demi lune washer
4 pieces
Gently thread nut onto
steel rod, and tighten
finger tight.
BF104 M8 nut
4 pieces
5
Jemima 4 Poster Bed
1. Ease the Headboard panel and rail
on to the fittings on the post.
2. Insert Demi lune washer (part BF
103) and nut (part BF 104) in to place
as you push the posts onto the rail
and headboard panel
1. Insert threaded rod (part BF 105)
into the inset in the post
2. Assemble the front post and footer
panel using demi lune washer (part
103) and nut (part BF 104)
Ensure all fittings are tight

Assemble the Bed frame
1. Insert the threaded rod (part BF
105) into the central hole of both
headboard posts and ease the rail into
place, insert demi lune washer (part
BF 103) and nut (Part BF 104) and
tighten to finger tight.
2. Follow with second bed rail
3. Insert the threaded rod (part BF
105) into cental holes in both posts of
the foot board. Offer up the rails on to
the fittings, insert the demi lune
washers (part BF 103) and the nut
(part BF104)
Tighten all fittings at this stage
6
Jemima 4 Poster Bed

Fit the slats
2. Secure the slats to the base using
the top nut nut (part BTH) and the
bolts (parts B640)
Top hat bolt
6 pieces
BTH
B630 M6 x 30mm
6 pieces
7
Jemima 4 Poster Bed
1. Unroll the slats ensuring that the
webbing is face down , align the holes
in the slats with those on the slat
support rails

Fit the canopy rails
1. Start with most convenient rail
2. Place second rail in place ( this is a
2 person job) and secure first corner
with bolt (part B640).
3. work around the bed, securing the
canopy rails as you go
Periodically check all fittings are tight
B640 M6 x 40mm
4 pieces
8