The GigRig GENX14 User manual

TheGigRig Ltd February 2023
GENX14 HIGH CURRENT
DC SUPPLY MANUAL

1
The GigRig Ltd
Unit 15 Whitehill Industrial Pk, Whitehill Lane
Royal Wootton Bassett, Wiltshire. UK
SN4 7DB
THEGIGRIG GENX 14 MANUAL
TheGigRig GenX14
TheGigRig GenX14 is the crowning glory of TheGigRig Modular Power Supply system. It features 14 isolated
outputs capable of powering even the most current hungry pedalboards.
GENX14 DC OUTPUTS
8x9VDC@200mA: 8 individual 9VDC outputs capable of a conservative 200mA each. This is more than enough for
most pedals. All your standard overdrives, analog modulation and delay pedals will be able to be powered from
one of these outlets.
4x9VDC@500mA: 4 individual 9VDC outputs capable of 500mA each. This is for your current hungry digital pedals
from brands like Strymon, Eventide, Line6 etc. Each output will deliver exactly what these pedals need to operate
at their best.
2x9/12VDC@1000mA: If you run valve OD’s/preamps, or something like a H90, these will need a huge amount of
current to keep the pedal operating in the range it needs to be. These two outputs can each deliver a massive
1000mA each at either 9 or 12VDC. For pedals such as Kingsley and Effectrode this amount of current is a must
and delivered beautifully by the GENX14. Each of the 1000mA outputs has two sets of connection tabs. It might be
that you want to power a high current digital pedal and something else. The two sets of connection tabs for each
of the 1000mA outputs gives you this option.
DC Input: Plug your DC power in here. GenX14 is designed to work with the 24V DC power supply provided but it
will work on a wide voltage range from 9-34V DC. IMPORTANT - Whatever you put into the DC INPUT will appear
on the LINK OUT. Using the supplied 24V power supply, you will get 24V on the link out.
TheGigRig Cut-To Length DC Cable
One of the features of our Modular Power Supply
System is our cut to length DC cables. Measure out
exactly how long it needs to be, cut it to length, and
pop the end of the cables into the tabs and push flat.
Once connected the cable is locked into position.
You can of course remove the cable by levering up
the tab. If any insulation is left in the tab simply lever
the tab all the way out and poke the left over
insulation out with a paperclip or something similar

2
The GigRig Ltd
Unit 15 Whitehill Industrial Pk, Whitehill Lane
Royal Wootton Bassett, Wiltshire. UK
SN4 7DB
THEGIGRIG GENX 14 MANUAL
LOCK GUARD
To ensure you don’t accidentally send the wrong voltage into any of your expensive pedals we’ve provided a LOCK
GUARD on the switch. If you want to swap the voltage simply undo the two hex screws, remove the lock guard,
and flick the switch. Reattach the LOCK GUARD once you’ve changed the voltage.
SET UP EXAMPLE

3
The GigRig Ltd
Unit 15 Whitehill Industrial Pk, Whitehill Lane
Royal Wootton Bassett, Wiltshire. UK
SN4 7DB
THEGIGRIG GENX 14 MANUAL
Understanding the LINK output
The LINK output links to the
DC input. Powering the
GENX14 with the 24V
power supply provided
means the LINK output will
be 24V. If you power the
GENX14 with a Generator
the LINK output will be 9V.
For maximum efficiency we
recommend using the
supplied 24V power supply.
*PLEASE NOTE – High
Current Adapters made
before 2022 will not have
the wide range input
feature. HCAs capable of
24V at the input will have a
blue dot on the base.
You can also connect a Distributor to the LINK output if you need to run multiple HCA’s.
Isolators are 9V input ONLY and will need to be powered by any of the 9V outputs. As the Isolator is providing
isolated power it can be run from one of the set of tabs on the 1000mA output alongside whatever else you’re
powering, as long as you have ample current spare, but ONLY if its set to 9v.
Using Both Sets of Tabs On The 1000mA Outputs

4
The GigRig Ltd
Unit 15 Whitehill Industrial Pk, Whitehill Lane
Royal Wootton Bassett, Wiltshire. UK
SN4 7DB
THEGIGRIG GENX 14 MANUAL
FAQs
Is this ok to use in the USA?
You can use GenX14 in any country in the world. The 24V power supply that comes with the GenX14 will adapt to
any international input voltage, as will our Generator power supply. Either of these supplies can be used but we’d
recommended the supply provided for current hungry pedalboards.
Can I power the Quad Cortex?
The Neural Quad Cortex needs 12V@2000mA. If you sum the two 12v@1000mA outputs on GENX14 with a
current doubling cable then yes, there’s enough there to power the Quad Cortex.
What do I do if I need more outputs?
GenX14 is designed to operate as part of TheGigRig Modular Power Supply system so adding things is simple. If
you need lower current 9V outputs, add an Isolator ISOx4LC, if you need a different voltage such as 24V for an
older Electro-Harmonix pedal you can add an ElectroMan 9-24V High Current Adapter.
What’s the best way to attach GenX14 to my pedalboard?
We recommended using pedalboard tape to attach GenX14 to loop Velcro or double-sided tape to attach to a dry
flat surface. The supplied 24V power supply can live either on or off the pedalboard. If it is to live on the board
attach the same way.
Can I power GENX14 with my Generator?
GENX14 will work with any 2.1mm centre negative supply between 9V-36V. The 9V Generator will work, but it will
not run as efficiently as with the supplied 24V power supply. For the vast majority of boards its absolutely fine but
if you are using all the GENX14’s outputs with everything pushing the limit of GEN14’s current draw, then you may
be overloading the Generator.
How do I connect a dc cable?
To connect a dc cable to GenX14 simply cut the cable to length, and push the wire with the white stripe into the
white tab, and the black wire into the black tab
You MUST push the tabs flat to connect. Using the pair of pliers you use to cut the cable works well. Once
connected its locked in place.
How do I reuse a dc cable?
Lever up the tab then pull the wires out. If the wires are stuck make sure the tabs are all the way up, then pull the
wires free. If there is any insulation from the wires left over in the tabs simply lever the tabs all the way out and
poke the insulation out of the tab before returning it to its place. Cut the cable the length you want it and reinsert
it into the tabs and push the tabs flat.

5
The GigRig Ltd
Unit 15 Whitehill Industrial Pk, Whitehill Lane
Royal Wootton Bassett, Wiltshire. UK
SN4 7DB
THEGIGRIG GENX 14 MANUAL
Power Path Diagram Service
Power can be complicated. With so many pedals operating on different voltages, different current draw demands,
different plug sizes and polarities, its east to get confused. We offer a service where we will tell you exactly what
is needed to power everything on your board. Click the link, enter the details and we’ll respond with a diagram and
a link through to get everything you need.
https://shop.thegigrig.com/custom-power-path-diagram-service/
Thank You
By buying this GigRig product you are supporting a small team of ridiculously talented engineers, tech advisers,
production heroes, admin legends and their families. If you need anything please contact us through our support
page at thegigrig.com/support and don’t forget to check out our YouTube channel for more info.
Technical Specifications:
Input Voltage: 9-34Vdc 2.1mm centre negative
Output Voltages: 8x9Vdc@200mA, 4X9Vdc@500mA, 2x9or12Vdc@1000mA
Current Draw Main Unit: 5.6Amps @ 9Vdc
Input is reverse diode protected
Safety: The GigRig UnderLiner & UnderLiner FS are is designed for indoor use only - Don’t get them wet
Dimensions:
GENX14 – 158Lx82Wx22Dmm (6.22Lx3.22Wx0.87D”)
G24V Power Supply – 132Lx57Wx32Dmm (5.2Lx2.24Wx1.26D”)
Warranty:
The GigRig warrants the product to be free from defects in material and workmanship for a period of 2 years from the original
date of purchase. If the product fails within the warranty period, The GigRig will repair or, at our discretion, replace the product
and cover the cost of return shipping to the original purchaser. This warranty covers defects in manufacturing discovered while
using this product as recommended by The GigRig. This warranty does not cover loss or theft, nor does the coverage extend to
damage caused by misuse, abuse, unauthorized modification, improper storage, lightning, or natural disasters. Damage caused
by any of the above circumstances may result in a non-warranty repair fee
Legal:
In the case of malfunction, the purchaser’s sole recourse shall be repair or replacement, as described in the preceding
paragraphs. The GigRig will not be held liable to any party for damages that result from the failure of this product. Damages
excluded include, but are not limited to, the following: lost profits, lost savings, damage to other equipment, and incidental or
consequential damages arising from the use, or inability to use this product. In no event will The GigRig be liable for more than
the amount of the purchase price, not to exceed the current retail price of the product. The GigRig disclaims any other
warranties, express or implied. By using the product, the user accepts all terms herein.
Disposal:
Return the unit to The GigRig Ltd for disposal or use standard disposal for electrical equipment recommended in your country
Approved. Fully compliant with the RoHS√ standard.