THE STANDING DESK THE ÄNDERN MOTOR User manual

FOR VIDEO INSTALL INSTRUCTIONS GO TO TheStandingDesk.com/install
THE ÄNDERN MOTOR
MONO COLUMN ELECTRIC TABLE
ASSEMBLY INSTRUCTIONS
STANDING
THE
DESK
Article #: 929 011 369 0000
INCLUDED HARDWARE PACKAGE
INCLUDED TOOLS PLEASE REVIEW these instructions completely
and verify all parts are included in this package
before beginning assembly. Do not discard
the packaging until satised that the product
operates properly. Assembly and operation
of this desk must be in accordance with these
assembly instructions to avoid the risk of injury.
Keep these Assembly and Operation Instructions
near the assembly for reference.
REQUIRED TOOLS
5/16” Cable Clip (3)
Glides (4)
Socket Head
Cap Screw (4)
Flat Head
Cap Screw (4)
1/2” Wood
Screw (7)
1” Wood
Screw (4)
m5
Allen Wrench
m6
Allen Wrench
#2 Phillips Head
Screwdriver
1/2” Wrench
NOTE: Maximum lift capacity for the Ändern Motor desk is 175 lbs. The table support is
solely intended to serve the purpose of ergonomic adjustments for your desk in accordance with
the weights and measurements given in these instructions. Any usage other than that mentioned
in this document is inappropriate; the manufacturer disclaims liability for any resulting damages. In
such cases the user bears the full risk. The manufacturer cannot be held responsible for any losses
or damages resulting from unauthorized modications of this desk.
7/8” Cable
Clips (2)
INCLUDED CORDS AND
COMPONENTS
9/16” Wood
Screw (3)
Motor Control
Box (1)
3m Power Cord (1)
Motor Extension
Cable (1)
Control Handset (1)
SCAN
FOR
ASSEMBLY
VIDEOS

FOR VIDEO INSTALL INSTRUCTIONS GO TO TheStandingDesk.com/install 2
THE ÄNDERN MOTOR
MONO COLUMN ELECTRIC TABLE
ASSEMBLY INSTRUCTIONS
STANDING
THE
DESK
Thank you for choosing The Ändern Motor, a high-performance single column lift base with electric adjustment. It has been
manufactured with care and precision and it has passed numerous quality and safety checks to ensure trouble-free and safe
operation. You can be assured of lasting satisfaction with your Ändern Motor model.
Important Safety Information:
1. Assembly and operation of The Ändern Motor must be done in accordance with these assembly and operating instructions
- otherwise there is a risk of injury.
2. The Ändern Motor is solely intended to serve as an ergonomic adjustment device for desks in accordance with the weights
and measurements given in these assembly instructions. Any usage other than that mentioned in these instructions is
inappropriate; the manufacturer disclaims liability for any resulting damages. In such cases the user assumes responsibility
for all risk.
3. Please also take into account the general, legal and other regulations and legal provisions that are applicable - including
those that apply in the operator`s state - as well as the applicable environmental protection regulations. The regulations of
trade associations or other supervisory authorities that are in force locally must always be observed.
4. The manufacturer cannot be held responsible for any losses or damage resulting from unauthorized modications to The
Ändern Motor.
5. Keep the assembly and operating instructions near the device.
6. Never leave children unattended with this table base. Cleaning and user maintenance shall not be made by children without
supervision.
7. To avoid any danger of pinching it is necessary to keep a minimum distance of 1“ from the moving parts.
8. The assembly site should be dry, dust-free and without direct sunlight. Make sure that no liquid enters the column unit or
power supply as this could cause electrical shock or short circuit.
9. The duty cycle of the system is set to 2 minutes “ON” and 18 minutes “OFF” or 0.5 minutes “ON” and 9 minutes “OFF”. Power
cables must not be pinched, bent, stretched or mechanically stressed.
10. Load limits must not be exceeded.
11. Never open the housing of the power supply. Danger to the user can arise and the warranty will be voided as a result of
unauthorized opening of the housing and improper repairs. Only the manufacturer’s service technicians are authorized to
open or repair the electrical equipment.
12. In the event of a malfunction for example smoke, odors, unusual noises, or visible external damage, unplug the system and
call Customer Service.
With compliance to the provided guidelines, you will enjoy many years of satisfaction from your Ändern Motor. For any further inquiries please do
not hesitate to contact us.
Cleaning recommendations for powder-coated surfaces
For optimal care and cleaning of powder-coated surfaces the recommendations below should be followed:
• Use only a soft cloth or industrial cotton wool. Refrain from rubbing hard.
• Surface and cleaning agent temperatures <25°C. (Do not steam clean surface.)
• Clean stains with a damp soft cloth. Use cold or lukewarm water. Small amounts of neutral or alkaline detergent additives
may be used if necessary.
• Do not apply detergent for extended periods of time. If necessary repeat cleaning process after 24 hours. Wipe with cold
water immediately after cleaning. (Use a damp (not wet) cloth.)
• Do not use scratching or abrasive agents.
• Do not use acidic or strongly alkaline detergents.
• Do not use organic solvents which contain ester, ketone, alcohols, aromatic compounds, glycol ether, halogenated
hydrocarbons or similar substances.
NOTE: Do not lubricate or use silicone products on the dry guides in the guide columns to avoid squeaking of the guide columns.
Please pay attention to these assembly and operating
instruction to avoid a risk of injury!
Lifting capacity: maximum lift capacity of 175 lbs including ANY components above the top frame
(table top, desk top, accessories, etc.) Alteration of the system in any form is not permitted.

FOR VIDEO INSTALL INSTRUCTIONS GO TO TheStandingDesk.com/install 3
THE ÄNDERN MOTOR
MONO COLUMN ELECTRIC TABLE
ASSEMBLY INSTRUCTIONS
STANDING
THE
DESK
1
2
• Attach the top plate
to the column Flat
Head Cap Srews
and the m5 Allen
Wrench.
• Flip over the column
and top plate and
align the holes on
the top plate with
the pilot holes on
the worksurface.
• Attach the top plate
to the worksurface
with the 1” Wood
Screws and Phillips
Head Screwdriver.
Flat Head
Cap Screw (4)
1” Wood
Screw (4)
#2 Phillips Head
Screwdriver
m5
Allen Wrench
ATTENTION:
Do not plug
table into electrical
outlet until all steps
are completed and
directions state to.

FOR VIDEO INSTALL INSTRUCTIONS GO TO TheStandingDesk.com/install 4
THE ÄNDERN MOTOR
MONO COLUMN ELECTRIC TABLE
ASSEMBLY INSTRUCTIONS
STANDING
THE
DESK
3
4
• Slip the base over
the column and
attach the base with
the Socket Head
Cap Screw and the
m6 Allen Wrench.
Socket Head
Cap Screw (4)
m6
Allen Wrench
Motor Control
Box (1)
#2 Phillips Head
Screwdriver
9/16” Wood
Screw (3)
a. b.
c.
a. Align 9/16” Wood
Screws.
b. Screw half way into
the work surface.
c. Lower the Control
Box over the
Screws and slide
the control box
backward allowing
the Screws to seat
in the channels.
Tighten the three
Screws using the
#2 Phillips Screw
Driver.
DOWN
SLIDE
BACKWARD

FOR VIDEO INSTALL INSTRUCTIONS GO TO TheStandingDesk.com/install 5
THE ÄNDERN MOTOR
MONO COLUMN ELECTRIC TABLE
ASSEMBLY INSTRUCTIONS
STANDING
THE
DESK
5
6
• Run the Handset & Motor
Cables together and coil them.
• Using the 1/2” Wood Screws,
attach the 7/8” Cable Clips to
the worksurface to secure the
coiled Cables’ positions.
• Slip the 5/16” Cable Clips
over the uncoiled Cables at
preferred placement and secure
with the 1/2” Wood Screws into
the pilot holes.
• Plug the Motor Cable into the
Column Cable.
• Attach the handset
to the worksurface
with the 1/2” Wood
Screws and a Phillips
Head Screwdriver.
(SEE REFERENCE
GUIDE ON p. 8)
• Plug the Handset
Cable and Motor
Cable into the
Control Box.
1/2” Wood
Screw (5)
#2 Phillips Head
Screwdriver
1/2” Wood
Screw (2) #2 Phillips Head
Screwdriver
NOTE: Motor Cable
MUST be plugged
into Motor Group
1 (M1) on Control
Box.
NOTE: Cable Clip positions are
USER DEFINED.
7/8” Cable
Clips (2)
5/16” Cable Clip (3)