The Telos Alliance Z/IPSTREAM R/2 Instruction Manual

We know you are excited to start using your new R/2, so let’s get
started…. The initial configuration consists of the following steps:
1. Connect to power
2. Connect to network
3. Connect audio
4. Assign IP addresses via the front panel
5. Continue product configuration from a web browser
WELCOME TO Z/IPSTREAM R/2TM
QUICK-START INSTALLATION GUIDE

QUICK-START INSTALLATION GUIDE
CONNECT TO POWER
A B E F
C D HG
A. Power
B. RS232
C. Control Port
D. USB Ports
E. NIC 1
F. NIC 2
G. Audio 5-8
H. Audio 1-4
The R/2 comes with a dual power supply (120V - 240V, 50 - 60Hz) for
enhanced reliability. Please connect the power cords to both power
connectors on the back, using separate power sources. If you are only
connecting one of the power supplies, you may remove the other power
supply, either fully or partially, to avoid a power supply alarm condition.
Advisory: Your R/2 runs a powerful quad-core processor, and needs to keep
cool for best performance. During boot up, the fans are loud, as they start
at full power, but will quiet down after the boot-up is complete. We suggest
that your R/2 be installed in an area where the occasional fan noise will not
be an issue.

Power up the R/2
ON / OFF
Press the On/Off button on the front/right side of the unit to power it up.
During the power up process, the front panel will light up and display a
splash screen. When the unit is ready, it will display the audio meters screen:
CONNECT TO NETWORK
The R/2 offers dual network adapters, NIC 1 and 2 (see image above).
The two adapters may be used to provide a redundant network path to
the Internet, or to separate the internal network (e.g. Livewire) from an
outside network.
Connect your network(s) to NIC 1 and/or NIC 2. Please do not connect both
NICs to the same network. Doing so may create confusion as to which NIC
to use to reach a specific destination.

QUICK-START INSTALLATION GUIDE
CONNECT THE AUDIO
The AES/EBU audio connections are provided through two 26-pin D-sub
connectors. Connect the breakout cable(s) to the D-sub connectors. Use
the thumbscrews to securely attach the cables in place.
ASSIGN IP ADDRESSES
The front panel uses four arrow keys along with OK and Cancel keys to
navigate and make choices.

After power up, the front panel will display the audio meters screen:
Press the right arrow key to navigate to the Interfaces screen:
Select NIC 1 or NIC 2 by using the up/down arrow keys. The display arrow
will move to indicate the current selection. Press the OK key to select the
desired interface. This will take you to the Network Mode screen:
By default, R/2 ships with the interfaces configured for DHCP. If you
wish to set up as static IP address manually, follow the directions in the
section below.

QUICK-START INSTALLATION GUIDE
If you wish to see the currently assigned IP settings, press the right
arrow key.
Static IP Configuration
You may also assign a static IP address if you do not wish to use DHCP.
On the Network Mode screen, press the OK key. You will be asked to
switch to static IP mode.

Use the up arrow key to select Yes, then press the OK key. The IP settings
screens will be displayed:
Follow the procedures below to update the IP configuration.
• Use the up/down arrow keys to select the field you want to change (IP
address, Netmask, or Gateway).
• Press the OK key to begin editing a field.
• While editing a field, use the left/right keys to select the digit you wish
to change, then the up/down arrows to change the value.
• When done editing, press the OK key.
When finished entering all values, press the right arrow key. You will be
prompted to save the new settings:
Use the up arrow key to select Yes, then press the OK key to select.

QUICK-START INSTALLATION GUIDE
After a few moments, you will be returned to the Network Mode screen:
If you’re using both NICs, repeat the steps above to configure NIC 2.
CONTINUING THE CONFIGURATION PROCESS
At this point, the initial hardware configuration is complete. The rest of
the configuration is performed through a web browser, from another
computer.
Make a note of the DHCP or static IP address configured above. On a
computer connected to the same network as the R/2, enter R/2’s IP
address in a web browser application. The unit may also be reached by
the hostname: R2-XXXXXX. Where XXXXXX is the serial number of the
unit. For example, unit 74-1001 will be R2-741001. The following login
prompt will be displayed:

Enter user as the username, leave the password field blank, then click
the Submit button. You should now be logged in to the Z/IPStream R/2.
Please refer to the manual for full product configuration information.

QUICK-START INSTALLATION GUIDE
INSTALLATION HELP
If you have more questions, you can access the full manual online at:
http://www.telosalliance.com/Telos/ZIPStream-R2- or reach the Telos
Alliance 24/7 Support Team via email at [email protected] or by
phone at [phone], we’d be happy to help you out.

THIS PAGE
INTENTIONALLY
LEFT BLANK

QUICK-START INSTALLATION GUIDE
1241 Superior Ave. • Cleveland, Ohio, 44114, USA • +1.216.241.7225 • TelosAlliance.com
p/n: 1490-00133-002 © 2017 TLS Corp. The Telos Alliance®. All Rights Reserved. C17/1/19025
Download the Manual
TelosAlliance.com/Telos/ZIPStream-R2-
Subscribe to DirectCurrent
Weekly updates on all things broadcast via email
TelosAlliance.com/directcurrent
Social Media
Facebook: /TelosAlliance
Twitter: @TelosAlliance
LinkedIn: /TelosAlliance
YouTube: TelosAllianceTV
Google+: +TelosAlliance
Product Catalog
TelosAlliance.com/mobile
QUICK LINKS