THE WORLD MODELS Super Frontier Senior A088S User manual

Warning! This model is not a toy.
It is designed for maximum performance. Please seek advice if one is not familiar with this kind
of engine powered precision model. Operating this model without prior preparation may cause
injuries. Remember, safety is the most important thing. Always keep this instruction manual at
hand for quick reference.
*Specifications are subject to change without notice.*
INSTRUCTION MANUAL
Wing Span
Wing Area
Flying Weight
Fuselage Length
80.5 in / 2040 mm
1232 sq in / 79.5 sq dm
8.6 Ib / 3900 g
65.5 in / 1670 mm
Specifications
FACTORY PRE-FABRICATED
ALMOST-READY-TO-FLY(ARF)SERIES
MADE IN CHINA
The World Models
Manufacturing Co., Ltd.
www.theworldmodels.com
(A088S)
0.46 cu. in. displacement 2 - stroke
Radio required: 4-channel radio w/ 5 sdandard servos
A088SPO30511508

INDEX
BEFORE YOU BEGIN
BEFORE YOU BEGIN
PARTS LIST
ASSEMBLY
SAFETY PRECAUTIONS
P.1
P.2
P.3-P.11
P.12
Check all parts. If you find any defective or missing parts contact your local dealer. Please
DRY FIT and check for defects for all parts that will require CAor Epoxy for final assembly.
Any parts you find to be defective after the gluing process may be difficult to remove for
warranty replacement. The manufacturer will replace any defective parts, but will not extend
to the parts that are good before gluing to defective parts during assembly. Warranty will
not cover any parts modified by customer.
Symbols used throughout this instruction manual comprise of the following :-
Read through the manual before you begin, so you will have an overall idea of what to do.
1
2
3
P.1
Cut off shaded portion.
Ensure smooth non-binding
movement while assembling.
Apply instant glue
(C.A.glue, super glue.)
Assemble left and right
sides the same way.
Peel off shaded portion
covering film.
Pay close attention here!
Apply epoxy glue.
Must be purchased separately !
Drill holes with the specified
diameter (here: 3mm). Pierce the shaded portion
covering film.
3mm
Do not overlook this symbol !
Warning!
Apply thread locker
A088SPO30511508

Parts List
P.2
COVERING:--
TOUGHLON STL 100 WHITE
TOUGHLON STL 250 BLUE
TOUGHLON STL 251 SKY BLUE
TOUGHLON STL 314 FUCHSIA
TOUGHLON STL 351 DARK BLUE
1. MAIN WING -- 1 pair
2. SCREW PB2x20mm -- 4 pcs
FUEL TUBE Ø6x5mm -- 4 pcs
CLEVIS PL4112103 -- 2 pcs
STRAPER PL4112102 -- 2 pcs
HORN PL4113101 -- 2 pcs
PUSHROD Ø1.8x130mm w/ Threads (For Aileron Servo ) -- 2 pcs
3. WOODEN 12x22x346mm (Wing Joiner)(A) -- 1 set
WOODEN Ø10x180.5mm (Wing Joiner)(B) -- 1 set
4. FUSELAGE -- 1 set
COVERING -- 1 set
5. STABILIZER & ELEVATOR -- 1 set
6. VERTICAL FIN & RUDDER -- 1 set
7. MAIN LANDING GEAR -- 1 set
MAIN WHEEL Ø76mm -- 2 pcs
COLLAR Ø4.1mm w/ set screw -- 4 sets
SCREW PM4x40mm -- 2 pcs
SOCKET HEAD SCREW M3x16mm -- 4 pcs
WASHER d4xD9mm --- 8 pcs
WASHER d3xD7mm --- 4 pcs
QUICK RELEASE NYLON RIVET -- 4 pcs
SCREW KA2.3x8mm -- 4 pcs
M4 NUT -- 2 pcs
WHEEL PANT -- 1 pair
MOUNTING PLATE 1mm -- 2 pcs
8. SOCKET HEAD SCREW M4x25mm -- 4 pcs
WASHER d4xD9mm --- 4 pcs
ENGINE MOUNT PL 5111050 -- 1 set
9. FUEL TANK 380cc PL1111380 -- 1 set
DOUBLE-SIDED TAPE 40x10mm -- 1 pc.
CABLE TIE 1.5x5x400mm -- 1 pc.
10. SCREW PA3x14mm -- 4 pcs
STEERING ARM STAND PL4116042 -- 1 pc.
PLYWOOD 3x25x30mm (For Steering Arm Stand) --1 pc.
11. WIND SHIELD -- 1 pc.
SCREW PWA 2.3x8mm -- 4 pcs
SILICON GROMMET d1.5xD6.5mm -- 4 pcs
12. NOSE LANDING GEAR -- 1 set
FRONT WHEEL Ø76mm -- 1 pc.
COLLAR Ø4.6mm -- 4 set
STEERING ARM PL4112406 -- 1 set
WHEEL PANT -- 1 pc.
MOUNTING PLATE PL4114020 -- 1 pc.
SCREW PA 2.6x10mm -- 2 pcs
FRONT WHEEL PUSHROD Ø1.6x320mm -- 1 pc.
PLASTIC TUBE d2xD3x200mm -- 1 pc.
13. SOCKET HEAD SCREW M3x30mm -- 4 pcs
WASHER d3xD7mm -- 8 pcs
M3 NUT -- 8 pcs
THROTTLE PUSH WIRE Ø1.2x445mm -- 1 pc.
PLASTIC TUBE d2xD3x200mm -- 1 pc.
14. SCREW PWA2.6x12mm -- 4 pcs
SILICON GROMMET d1.5xD6.5mm -- 4 pcs
COWLING -- 1 pc.
TRANSPARENT 3D TEMPLATE -- 1 pc.
SPINNERØ52mm -- 1 set
15. SIDE WINDOWS -- 1pair
16. LINKAGE CONNECTOR Ø2.1mm HW7111060 -- 2 sets
17. SCREW PB2x16mm -- 2 pcs
FUEL TUBE Ø6x5mm -- 1 pc.
CLEVIS PL4112103 -- 1 pc.
HORN PL4113101 -- 1 set
PUSH ROD Ø1.8x1135mm w/ Threads (For Elevator Servo) -- 1 pc.
18. SCREW PM2x16mm -- 2 pcs
M2 NUT -- 2 pcs
FUEL TUBE Ø6x5mm -- 2 pcs
COPPER TUBE Ø2.5xD3.2x8mm --2 pcs
EYE SCREW Ø1.8x27mm w/ Threads (For Rudder) -- 2 pcs
HORN PL4113101 -- 2 pcs
CLEVIS PL4112103 -- 2 pcs
WIRE Ø1x1100mm(For Rudder) -- 2 pcs
19. SPONGE 60x70x122mm -- 1 pc.
FUEL TUBE Ø6x5mm -- 1 pc.
STRAPER PL4112102 -- 1 pc.
COPPER TUBE Ø2.5xD3.2x8mm --2 pcs
RIGGING Z BEND Ø1.8x27mm(For Rudder) -- 2 pcs
CHARGE RECEPTACLES KP0041300 -- 1 pc.
20. PILOT PC001085B --1 set
PLYWOOD 3x45x122mm (For Pilot) -- 1 pc.
BALSA 6x6x45mm (For Pilot Stand) -- 2 pcs
21. SOCKET HEAD SCREW M3x30mm -- 2 pcs
WASHER d3xD12mm -- 2 pcs
PLYWOOD 3x40x120mm (For Wing Protection) --1 pc.
22. DECALS A088DEC -- 1 set
A088SPO30511508

P.3
Aileron Servo Lead
Wing Joiner(A)
12x22x346mm
Wing Joiner(B)
Ø 10x180.5mm
Main Wing
1
Bottom View
Bottom View
2Aileron Servo
3Main Wings
Ø1mm pilot holes for World Models horn are pre-drilled. Please look for pin-hole
marks at under side of control surfaces.
Please dry fit wing joiner into left and right wing to make sure they fit with the
proper dihedral angle, mark the wing joiner if necessary. Apply epoxy glue to
both sides of all surfaces in contact. Use a stick to apply the glue to inner side
of wing joiner sleeve, and apply the glue to wing joiner before putting them
together. Wing joiner not glued properly will lead to wing failure and plane crash.
TWM PL8210010
CLEVIS WRENCH
PB2x20mm Screw
4
PB2x20mm
Fuel Tube
D6x5mm
Clevis
Pushrod
Ø1.8x130mm
Horn
Pre-glued
Pushrod
Ø1.8x130mm
Straper
Fuel Tube
D6x5mm
A088SPO30511508

Fuselage
4
P.4
Stabilizer / Elevator
5
Vertical Fin / Rudder
6
Pre-glued
Pre-glued
Covering
Decal
Remove coverings for all surfaces in contact before applying A/B epoxy glue.
Remove coverings for all surfaces in contact before applying A/B epoxy glue.
B B'
B=B'
1
2
3
A088SPO30511508

P.5
Landing Gear
7
Engine Mount
8
PM4x40mm Screw
d4xD9mm Washer
8
4.1mm Collar
4
2
M4 Nut
d3xD7mm Washer
4
d4xD9mm Washer
4
2
KA2.3x8mm Screw
4
Plate 1mm
d4xD9mm Washer
d3xD7mm Washer
Wheel Ø76mm
3mm
Set Screw
3mm
Set Screw
4.1mm
Collar
4.1mm
Collar
Wheel
Pant
M4 Nut
PM4x40mm
M3x16mm
Bottom View Completed
d2xD8mm
Quick Release Nylon Rivet
4
KA2.3x8mm Washer d4xD9mm
Quick Release Nylon Rivet
4
M3x16mm Socket Head Screw
4
M4x25mm Socket Head Screw
Engine Mount PL5111050
M4x25mm
d4xD9mm
Apply thread locker to screws
Blind nuts are off-centered
to keep the spinner at the
fuselage axis.
A088SPO30511508

P.6
Fuel Tank
9
Nose Landing Gear
10
Wind Shield
11
PA3x14mm Screw
4
Bottom View
Fuel Tank
380CC
Plywood 3x25x30mm
SteeringArm Stand
PA3x14mm
Cable Tie 1.5x5x400mm
PA2.3x8mm Screw
4
PWA2.3x8mm
Silicon Grommets
Canopy
Fuselage
d1.5xD6.5mm Silicon Grommet
4
PWA2.3x8mm
Silicon Grommets
Double-sided Tape 40x110mm
A088SPO30511508

P.7
Nose Landing Gear
12
Engine
13
Wheel Ø76mm
4.6mm Collar
4.6mm Collar
4.6mm Collar
4.6mm Collar
PA2.6x10mm
105mm
4.13 in.
Mounting Plate
Nose Landing Gear
Wheel Pant
SteeringArm
4.1mm Collar
4
PA2.6x10mm Screw
2
Throttle Pushwire
Ø1.2x445mm
Plastic Tube
d2xD3x200mm
M3x30mm
d3xD7 Washer
M3 Nut
M3x30mm Socket Head Screw
d3xD7mm Washer
4
8
8
M3 Nu t
Illustration is for inverted
mounting. You can mount
the engine upright or side
ways simply by rotation
the engine mount. Thrust
angles will not be affected.
Plastic Tube
d2xD3x200mm
Nose Wheel
Steering Pushrod
Ø1.6x320mm
3mm Set Screw
3mm Set Screw
3mm Set Screw
A088SPO30511508

P.8
Cowling
14
Servo Set
16
Windows
15
Cowling Fuselage
d1.5x6.5mm
Silicon Grommet
PWA2.6x12mm
Throttle Pushwire
3x3mm Set Screw
Washer
2mm
Washer
2mm
M2 Nut
Throttle Servo
1.5mm
Please refer to the attached sheet for linkage connector installation.
3x3mm Set Screw
M2 Nut
Linkage Connector
2
2
2
4
2mm Washer
First insert the grommet to the
cowling then apply screw.
PWA2.6x12mm
Silicon Grommets
Windows
Spinner Ø52mm
Battery Cover
PWA2.6x12mm Screw
4
d1.5xD6.5mm Silicon Grommet
4
A088SPO30511508

P.9
Elevator Pushrod
17
Bottom View
Ø1mm pilot holes for World Models horn are pre-drilled.
Please look for pin-hole marks at under side of control surfaces.
PB2x16mm Screw
2
TWM PL8210010
CLEVIS WRENCH
PB2x16mm
Fuel Tube
D6x5mm
Clevis
Pushrod
Ø1.8x1135mm
Horn
PM2x16mm Screw
2
2
Rudder Pushwire
18
TWM PL8210010
CLEVIS WRENCH
Copper Tube
d2.5xD3.2x8mm
Eye Screw
Clevis PM2x16mm
Horn
M2 Nut
Rudder pushwire
Ø1x1100mm
Ø1mm pilot holes for World
Models horn are pre-drilled.
Please look for pin-hole marks
at under side of control
surfaces.
M2 Nut
A088SPO30511508

P.10
Pilot
20
Balsa 6x6x45mm Double-sided Tape
Pilot Plywood 3x45x122mm
Radio Equipment
19
Install and arrange the servos as shown in the diagram.
Front Sponge Battery
Fuel Tube
D6x5mm
Straper Rudder Pushwire
Ø1x1100mm
Elevator Pushrod
Ø1.8x1135mm
Throttle Pushrod
Ø1.2x445mm
Rigging Z Bend
Ø1.2x27mm
Rudder Servo
Receiver
Throttle Servo
Elevator Servo
Press down the center 1/3 portion
Copper Tube
Nose Wheel
Steering Pushrod
Ø1.6x320mm
Plastic Tube
d2xD3x200mm
Charge Receptacles
KP0041300
A088SPO30511508

Main Wings
21
P.11
2
d3xD12mm Washer
2
Wing Setting
22
Completed
M3x30mm Plywood 3x40x120mm
A=A` B=B` C=C` D=D`
d3xD12mm Washer
M3x30mm Socket Head Screw
A A`
C`
D`
CD
B`B
A088SPO30511508

# First time flyer should never fly by himself / herself. Assistance from experienced flyer is absolutely necessary.
# Pre-flight adjustment must be done before flying, it is very dangerous to fly a badly pre-adjusted aircraft.
# is is specially designed to be powered by 0.46 cu. in. displacement 2 - stroke, using a more powerful
engine does not mean better performance. In fact, over powered engine may cause structural damage and injuries.
# Make sure the air field is spacious, never fly the plane too close to people and never get too close to a running propeller.
Extreme caution should be exercised when working with electric powered models. Make sure the propeller is cleared of all
objects, especially your hands before connecting the battery to the model. Make sure you understand the operation of the ESC
(Electronic Speed Control) by studying the ESC manual. Once you plug in the battery for electric powered model, always treat
the propeller as a rotating one, as accidental movement of the throttle stick will spin the propeller and could cause injuries.
# If you find wrinkles on the covering as a result of weather changes, you can use hot iron to remove the wrinkles. Please begin
with lower temperature setting and gradually raise the temperature until the wrinkles are gone. Too hot an iron may damage the
covering. Don't use hot iron near the seams or edges, hot iron will melt the glue and shrink the covering at the same time,
causing the seams to pull away.
# Check and re-tighten up all factory assembled screws, use thread locker if necessary.
P.12
Important Safety Precautions
Warning!
Control Throws
23
C.G.
24
The ideal C.G. position is 100mm ( 3.94 in. ) behind the leading edge measured at
where the wing meets the fuselage. In order to obtain the C.G. specified, add
weight to the fuselage or move the battery position. Check the C.G. before flying.
If you are converting this model to electric, please move the C.G. forward 5% of
current C.G. distance from leading edge to compensate for weight of fuel.
100mm
C.G.
29mm
29mm
Elevator
35mm
35mm
Rudder
12mm
12mm
Ailerons
Adjust the control throws as shown in the diagram. These throws
are good for general flying. You can adjust according to your
personal preference.
3.94 in.
http://www.theworldmodels.com/para/instruction/instructionManuals.php
A088SPO30511508

LINKAGE CONNECTOR
HW7111050 & HW7111060
After fastening the round nut, make sure that
the linkage connector can rotate freely.
Drill 2mm hole at servo horn. Insert linkage connector
into servo horn.
Make sure shoulder of
screw is cleared from
servo horn.
Add washer to reduce
play if necessary.
Shoulder
Tighten up the round nut
against the shoulder. Apply
CA or permanent thread
locker.
Product Registration Form (US Customers)
We would like to share with you any relevant information regarding your model, including
product news and free upgrade parts when applicable. Please fill in the following and
send toAirBorne Models, 4749-K,Bennett Drive, Livermore, CA94551 USA.
1. Name:______________________________________________
2.Address:____________________________________________
3. Phone #:____________________ E-mail:__________________
4. Model:______________________________________________
Wing QC#__________ Fuselage QC# _______________________
(QC numbers are stamped on wing and fuselage)
5. Date of Purchase:_____________________________________
6. Store Name: _________________________________________
Please callAirBorne Models at 925 3710922 for any assistance in filling this
form.Thank you very much for purchasing our product.
A088SPO30511508

Optional Parts
Clevis Wrench
Code No. Size Package
PL8210010 1 set
Small Clevis Large Clevis
Field Stand
Code No. Size Package
Code No. Size Package
MS9111450 600 x 240 x 350mm 1 pc
( ACCESSORIES)
180mm Extension
Code No. Size Package
KW0011800 180mm 1 set
Charge Receptacles
Code No. Size Package
KP0041300
180mm Y-Cord
Code No. Size Package
KW0021800 180mm 1 pc
Special tool for clevis installation.
Suitable for standard and small
(EP) clevis.
Fuel Filler
Code No. Size Package
PL8110030 15 x 22 x 49mm 1 x 1 pc
SV4031 40.6 x 20 x 37mm 1 set
Speed : 0.17 sec / 60° @4.8V
0.14 sec / 60° @6.0V
Torque : 3.2kg.cm / 44.8 oz - in @4.8V
4.1kg.cm / 57.4 oz - in @6.0V
Size : 40.6 x 20 x 37mm /
1.60 x 0.79 x 1.46 in
Weight : 39.4 g / 1.39 oz
Standard Servo
A088SPO30511508

The World Models
Manufacturing Co., Ltd.
www.theworldmodels.com
A088SPO30511508