THE WORLD MODELS PAULISTINHA P-56 EP User manual

* Specifications are subject to change without notice. *
INSTRUCTION MANUAL
Warning! This model is not a toy.
It is designed for maximum performance. Please seek advice if one is not familiar with this kind
of engine powered precision model. Operating this model without prior preparation may cause
injuries. Remember, safety is the most important thing. Always keep this instruction manual at
hand for quick reference.
Wing Span 48.5 in / 1230 mm
Wing Area 330 sq in / 21.3 sq dm
Flying Weight 28 oz / 800 g
Fuselage Length 30 in / 760 mm
Specifications
FACTORY PRE-FABRICATED
ALMOST-READY-TO-FLY (ARF) SERIES
MADE IN CHINA
The World Models
Manufacturing Co., LTD.
www.theworldmodels.com
(E326)
PAULISTINHA P-56 EP
PAULISTINHA P-56 EP
Requires: 4-channel radio w/ 4 micro servos. Outrunner
Motor KM0283011 w/ Propeller Adaptor HW2340100
20A Brushless ESC, 3 cells 11.1V 15C 1800 mAh Li-Po
battery & charger.
E326PO28761301

P.1
INDEX
Read through the manual before you begin, so you will have an overall idea of what to do.
BEFORE YOU BEGIN
BEFORE YOU BEGIN
PARTS LIST
ASSEMBLY
SAFETY PRECAUTIONS
P.1
P.2
P.3-P.10
P.10
Check all parts. If you find any defective or missing parts contact your local dealer. Please
DRY FIT and check for defects for all parts that will require CA or Epoxy for final assembly.
Any parts you find to be defective after the gluing process may be difficult to remove for
warranty replacement. The manufacturer will replace any defective parts, but will not extend
to the parts that are good before gluing to defective parts during assembly. Warranty will
not cover any parts modified by customer.
Symbols used throughout this instruction manual comprise of the following :-
1
2
3
Cut off shaded portion.
Ensure smooth non-binding
movement while assembling.
Apply instant glue
(C.A.glue, super glue.)
Assemble left and right
sides the same way.
Peel off shaded portion
covering film.
Pay close attention here!
Apply epoxy glue.
Must be purchased separately !
Drill holes with the specified
diameter (here: 3mm). Pierce the shaded portion
covering film.
3mm
Do not overlook this symbol !
Warning!
Apply thread locker
PAULISTINHA P-56 EP
PAULISTINHA P-56 EP
E326PO28761301

P.2
Parts List
1. MAIN WING -- 1 pair
2. MICRO AILERON SERVO MOUNT (For Aileron) PL5310020 -- 1 pair
CLEVIS PL4112105 -- 2 pcs
STRAPER PL4112106 -- 2 pcs
FUELTUBE d2xD4x4mm -- 4 pcs
SCREW PB2x14mm -- 4 pcs
SCREW PA1.7x8mm -- 8 pcs
PUSHROD D1.4x69mm w/ Threads (For Aileron) -- 2 pcs
HORN PL4113102 -- 2 sets
WING JOINER 5x13x82mm -- 1 pc.
3. STABILIZER & ELEVATOR -- 1 set
FUSELAGE -- 1 pc.
ELEVATOR LINK PL4510010 -- 1 set
SCREW PB2x8mm -- 2 pcs
BALSA3.5x6x7.5mm -- 1 pc.
4. VERTICAL FIN & RUDDER -- 1 set
5. TAIL LANDING GEAR PL3410030 -- 1 set
TAIL WHEEL Ø23mm -- 1 pc.
PLASTIC COLLAR Ø1.1mm w/ set screw -- 2 pcs
SCREW PA2x8mm -- 2 pcs
SCREW PM2x8mm -- 1 pc.
M2 NUT -- 1 pc.
ALUMINUM PLATE 0.3mm -- 1 pc.
6. SCREW PB2x8mm -- 2 pcs
CLEVIS PL4112105 -- 1 pc.
FUELTUBE d2xD4x4mm -- 1 pc.
HORN PL4113102 -- 1 set
PUSHROD Ø1.4x413mm w/ Threads (For Rudder) -- 1 pc.
7. CLEVIS PL4112105 -- 1 pc.
FUELTUBE d2xD4x4mm -- 1 pc.
PUSHROD Ø1.4x403mm w/ Threads (For Elevator) -- 1 pc.
8. SOCKET HEAD SCREW M3x6mm -- 4 pcs
WASHER d3xD7mm -- 4 pcs
SPINNER Ø28mm -- 1 set
9x6 FOLDING PROPELLER SET PL6313031 -- 2 pcs
COWLING -- 1 pc.
SCREW PWA2x8mm -- 4 pcs
9. WINDOWS -- 1 set
SCREW PWA2x8mm -- 4 pcs
COVERING:
LIGHTEX SGX 201 BLACK
LIGHTEX SGX 310 RED
LIGHTEX SGX 204 CREAM
10. SPONGE 10x50x150mm -- 2 pcs
DOUBLE-SIDED TAPE 30x35mm -- 1 pc.
FUELTUBE d2xD4x4mm -- 2 pcs
BATTERY TIE 200mm-- 1 pc.
STRAPER PL4112106 -- 2 pcs
11. MAIN LANDING GEAR Ø2.5mm -- 1 set
MAIN WHEEL Ø50mm -- 2 pcs
LANDING WIRE STRAPS PL4114030 -- 3 pcs
PVC PLATE 32x6mm (For Main Landing Gear) -- 2 pcs
BALSA 2x73x80mm (Main Landing Gear Cover) -- 2 pcs
SCREW PA2.6x10mm -- 6 pcs
COLLAR Ø2.6mm w/ Set Screw -- 4 sets
SCREW PM2x6mm -- 4 pcs
WASHER d2xD5mm -- 5 pcs
M2 NUT -- 4 pcs
TRANSPARENT DECALS 20x70mm -- 4 pcs
SCREW PM2x10mm -- 1 pc.
M2 NYLON INSERT LOCK NUT -- 1 pc.
MOUNTING PLATE PL4114015 -- 1 pc.
PLYWOOD 2x60.7x62.7mm -- 1 pc.
12. SCREW PM2.5x25mm -- 2 pcs
WASHER d2.5xD8mm -- 2 pcs
WING PROTECTION PLATE 6x25x82mm -- 1 pc.
13. SCREW PA2.3x8mm -- 6 pcs
WING STRUTS -- 1 pair
14. DECALS: E326DEC -- 1 set
E326PO28761301

P.3
Main Wing1
Aileron Servo Lead
Bottom View
Bottom View
Bottom View
Aileron Servos
2
PA1.7x8mm
02L
03L
04L
02R
03R
04R
Straper Fuel Tube
d2xD4x4mm
PA1.7x8mm
Please choose either (02L&02R) or (03L&03R) or (04L&04R) that suits your servo.
Ø1mm pilot holes for World
Models horn are pre-drilled.
Please look for pin-hole marks
at under side of control surfaces.
PB2x14mm Screw
4
8
PA1.7x8mm Screw
TWM PL8210010
CLEVIS WRENCH
Apply instant type CA glue to both sides of each hinge.
PB2x14mm
Fuel Tube
d2xD4x4mm
Clevis
Pushrod
Ø1.4x69mm
Horn
Wing Joiner 5x13x82mm
Please dry fit wing joiner into left and right wing to make sure they fit with the proper dihedral angle, mark the wing joiner
if necessary. Apply epoxy glue to both sides of all surfaces incontact. Use a stick to apply the glue to inner side of wing
joiner sleeve, and apply the glue to wing joiner before putting them together. Wing joiner not glued properly will lead to
wing failure and plane crash.
E326PO28761301

P.4
Stabilizer & Elevator
3
Vertical Fin & Rudder
4
Completed
Completed
A A'
A=A'
(Stabilizer)
(Main Wing)
B B'
B=B'
Temporary install the main wing, adjust
leveling of the stabilizer to make it as
parallel to the main wing as possible .
C C'
C=C'
Remove coverings for all surfaces in contact before
applying A/B epoxy glue.
Ø1mm pilot holes for World Models
horn are pre-drilled. Please look for
pin-hole marks at under side of control
surfaces.
Apply instant type CA glue to both sides
of each hinge.
PB2x8mm
Balsa 3.5x6x7.5mm
PB2x8mm Screw
2
Apply instant type CA glue
to both sides of each hinge.
Remove coverings for all
surfaces in contact before
applying A/B epoxy glue.
E326PO28761301

P.5
2
1
1
Rudder Pushrod
6
Elevator Pushrod
7
Tail Landing Gear
5
Bottom View
Bottom View
Bottom View
PA2x8mm Screw
PM2x8mm Screw
M2 Nut
PB2x8mm Screw
2
Ø1mm pilot holes for World Models horn are pre-drilled.
Please look for pin-hole marks at under side of control surfaces.
TWM PL8210010
CLEVIS WRENCH
TWM PL8210010
CLEVIS WRENCH
Clevis
Fuel Tube
d2xD4x4mm
Pushrod
Ø1.4x403mm
Clevis
Horn
Fuel Tube
d2xD4x4mm
PB2x18mm
Pushrod
Ø1.4x413mm
Plastic
Collar
Wheel Ø23mm
PA2x8mm
PM2x8mm
M2Nut
SteeringBracket
E326PO28761301

P.6
Outrunner Motor / Cowling
8
Completed
Washer d3xD7mm
M3x6 mm
PWA2x8 mm
9x6mm PL6313031
PWA2x8mm Screw
EZ Connector
Solder Solder
TWM
KP0011310
ESC Motor
Ø28mm Spinner
PA1.7x8mm
TWM HW3111400
PROPELLER ADAPTOR WRENCH
Don’t over-tighten the PM2 screws, let
the propeller blades align themselves
when spinning.
PA1.7x8mm Screw
2
PM2x12mm Screw
2
d3xD7mm Washer
4
4
4
M3x6mmSocketHeadScrew
Outrunner Motor 28/ 30
KM0283011
PropellerAdaptor
(d3xD5) HW2340100
PropellerAdaptor Wrench
TWM HW3111400
Optional Parts
PM2x12mm
PM2x12mm
Make sure rotating
motor casing is not
in contact with
wirings or anything.
Don't over-tighten the M3 screws, too
much stress on the screws could split
the firewall.
E326PO28761301

P.7
Windows
9
Radio Equipment
10
Bottom View
Securely glue the windows to the fuselage.
lnstall and arrange the servo as shown in the diagram.
Front
PWA2x8mm Screw
PWA2x8mm
4
Brushless ESC
Battery Tie
Battery Tie Battery
Battery Sponge
Sponge
Sponge
Receiver
Double Sided Tape
Straper
ElevatorServo
RudderServo
Elevator Pushrod
Rudder Pushrod
FuelTube
d2xD4x4mm
E326PO28761301

P.8
Main Landing Gear
11
Main Wing
12
Wing Struts
13
PM2x10mm Screw
M2 Nut
1
4
M2 Nylon Insert Lock Nut
1
PM2.5x25mm Screw
2
PM2x6mm Screw
PA2.6x10mm Screw
4
4
6
5
d2xD5mm Washer
2
d2.5xD8mm Washer
M3 x 3mm
Set Screw M3 x 3mm
Set Screw
Wheel Ø50mm
2.6 mm Collar 2.6 mm Collar
D2.6mm Collar
PA2.3x8mm Screw
6
PM2.5x25mm
Washer d2.5xD8mm
Wing Protection Plate
PA2.3x8mm
PM2x6mm
M2 Nut
PVC32x6mm
Landing Gear Cover
Washer d2xD5mm
PM2x10mm
M2 Nylon
Insert Lock Nut
Fuselage
Mounting Plate
Washer d2xD5mm
PA2.6x10mm
Battery Cover
Landing Gear Cover
70x20mm
Transparent Decals
1mm
Bottom View
Bottom View
Front
E326PO28761301

P.9
Wing Setting
14
Adjust the wing and fuselage configuration as shown in the diagrams.
A = A '
A A
'
B = B '
BB
'
C = C '
C C '
E326PO28761301

# First time flyer should never fly by himself / herself. Assistance from experienced flyer is absolutely necessary.
# Pre-flight adjustment must be done before flying, it is very dangerous to fly a badly pre-adjusted aircraft.
# is specially designed to be powered by KM0283011 Outrunner Motor.
# Make sure the air field is spacious, never fly the plane too close to people and never get too close to a running
propeller. Extreme caution should be exercised when working with electric powered models. Make sure the
propeller is cleared of all objects, especially your hands before connecting the battery to the model. Make sure
you understand the operation of the ESC (Electronic Speed Control) by studying the ESC manual. Once you
plug in the battery for electric powered model, always treat the propeller as a rotating one, as accidental
movement of the throttle stick will spin the propeller and could cause injuries.
# If you find wrinkles on the covering as a result of weather changes, you can use hot iron to remove the wrinkles.
Please begin with lower temperature setting and gradually raise the temperature until the wrinkles are gone.
Too hot an iron may damage the covering. Don't use hot iron near the seams or edges, hot iron will melt the
glue and shrink the covering at the same time, causing the seams to pull away.
# Check and re-tighten up all factory assembled screws, use thread locker if necessary.
P.10
15
Control Throws
16
C . G .
50 mm
http://www.theworldmodels.com/para/instruction/instructionManuals.php
2.0 in.
C.G.
Important Safety Precautions
Adjust the control throws as shown in the diagram.
These throws are good for general flying. You can
adjust according to your personal preference.
Aileron
10mm
Elevator 15mm
Rudder 25mm
25mm
15mm
10mm
Warning!
The ideal C.G. position is 50mm (2.0 in.) behind the leading edge measured at
where the wing meets the fuselage. In order to obtain the C.G. specified, add
weight to the fuselage or move the battery position. Check the C.G. before flying.
PAULISTINHA P-56 EP
PAULISTINHA P-56 EP
E326PO28761301

KM0283011
Large Clevis•
Small Clevis•
Pl8210010

E326PO28761301