thermal-vision IR313GT Instruction Manual

bling
1 CAUTION:
1 The assembling of IR
313GT
support. Without the authorization, users can not disassem
2 Please follow the
rules and steps in this manual
afford any legal or
economic
3 Without the authorized technician
fuse of the configuration
4 Please do not put the
IR
electric shock,
damage or fire
5 Output voltage of IR
313GT
other devices not
specified.
before connection between the
6 Connect the IR313GT
with power source without spe
IR313GT.
7 Photos below are only for reference, please
2 IR313GT
configurations
1 S
tandard configuration
NO.
1
2
NOTE: Bracket and
decoding box of Audi
2 Brackets for Audi A
6L
NO. Name
1 A6L Fasten kit
2 M4X10 screw (
fasten
3 M4X8 pan-
head screw
4 M5X16 pan-
head
5 T type cutting kit
6 Cable
for IR313GT and decoding box
Guide to installing thermal night vision camera to vehicle or ATV 4x4
313GT should be authorized by the factory or local technical
support. Without the authorization, users can not disassemble or repair.
rules and steps in this manual
，or
the manufacturer will
economic
liability .
3 Without the authorized technician
’s support, please do not chan
ge the cables or
location on the car.
IR
313GTin moist location or close to water
, which will cause
damage or fire
by short circuit.
313GT
is 12v, it is only for IR
output, please do not connect
specified.
Please disconnect the IR313G
T and the power source
before connection between the
IR313GT
and the other specified devices.
with power source without specified cables will damage the
7 Photos below are only for reference, please
subject to products.
configurations
tandard configuration
Name Quantity
IR313GT 1
Cable 1
decoding box of Audi
are needed
6L
Brackets for Audi A6L
fasten
the IR313GT)
head screw
(fasten the IR313GT)
head
tapping screw (fasten the IR313GT)
for IR313GT and decoding box
should be authorized by the factory or local technical
ble or repair.
the manufacturer will
not
ge the cables or
, which will cause
output, please do not connect
T and the power source
and the other specified devices.
cified cables will damage the
Quantity
1
3
1
4
1
1

3 Assembling
3.1 Arrangement of all devices
3.2 Assemble and route
3.2.1 Disassemble the
decoration panel on
frame in the picture
below.
3.2.2 Cut off the logo on
grating
Decoding box and BVS
IR313GT is configured
behind of the grating
3.1 Arrangement of all devices
decoration panel on
top of the
grating. Please check the red
below.
grating
(Or disassemble the component
inside t
Decoding box and BVS
are configured
at the top of the
container .
M
embrane switch
on the panel
the
steering wheel
grating. Please check the red
inside t
he logo).
at the top of the
embrane switch
is configured
on the panel
lower right to
steering wheel

Cut the circle inside the logo with T
3.2.3 Fasten
Fix
the IR313GT on the bracket
lower left of
the bracket. Please fasten the screw
Paste the tags for cutting
Cut the circle inside the logo with T
-type kit
the IR313GT on the bracket
, please notice that
it is the pan head screw
the bracket. Please fasten the screw
later af
ter the pitch angel
adjustment is completed.
it is the pan head screw
on the
ter the pitch angel

Fasten
the IR313GT with bracket
P
3.2.4 Route
Disassemble
the protection panel and the adhesive tape at the rear of the engine
compartment.
the IR313GT with bracket
behind the grating using 4 M5*15
tapping
P
reliminarily fasten of the IR313GT
the protection panel and the adhesive tape at the rear of the engine
A
dhesive tape
Protection panel
tapping
screws.
the protection panel and the adhesive tape at the rear of the engine
dhesive tape
Protection panel

Remove the 3 screws on AC air
with No.10 screw socket.
Remove the 3 screws on AC air
in vent set at
the rear of the engine compartment
To disassemble
the screw,
cloth
of the AC should be removed.
the rear of the engine compartment
the screw,
screen
of the AC should be removed.

Please wiring
as showing in the pictures and penetrate the cables follow the original
wiring.
The cables go into the
engine
go out of the engine com
partment
as showing in the pictures and penetrate the cables follow the original
engine
compartment through th
e AC air in vent and the cables
partment
from the rear of the containers.
as showing in the pictures and penetrate the cables follow the original
e AC air in vent and the cables

Notice:
cables near to the air in vent
Back of the container
cables near to the air in vent
should be protected with tapes

Cable leading out position in the cab.(
to
the air in vent of the engine compartment
Cable lead into the cab
from this position
4 Adjustments
1 Connect the IR313GT with BVS and power on
2 Adjust the pitch angel
manually
meters away,
is just in the middle of the
connecting IR313GT
as described
Cable leading out position in the cab.(Under the rear of the container, corresponding
the air in vent of the engine compartment
from this position
.
1 Connect the IR313GT with BVS and power on
manually
. When target, like pedestrian
in front of the car 30
is just in the middle of the
screen, fasten screws on the
bracket
as described
in 3.2.3.
Under the rear of the container, corresponding
in front of the car 30
bracket