Prorack K446 User manual

FittingKit
K446
EN
Fitting Instructions for Basic Carrier
ES
Instrucciones de montaje para el
sistema de transporte.
F
Instructions de montage pour Basic
Carrier
x 2
x 1
x 1
x 2
x 2
x 4
1
Revision No:
4C

FittingKit
K446
EN
MAX kgs (lbs)
W/P
WHD
Honda
Fit , 5dr Hatch 07-+
ZA
50 kgs (110 lbs)
50 kgs (110 lbs)
Fit , 5dr Hatch Aug 08-+
US
50 kgs (110 lbs)
50 kgs (110 lbs)
Fit , 5dr Hatch Aug 08-+
NZ
50 kgs (110 lbs)
50 kgs (110 lbs)
Jazz , 5dr Hatch 09-+
ZA
50 kgs (110 lbs)
50 kgs (110 lbs)
Jazz , 5dr Hatch Aug 08-+
AU
50 kgs (110 lbs)
50 kgs (110 lbs)
Jazz , 5dr Hatch Jul 08-+
NZ
50 kgs (110 lbs)
50 kgs (110 lbs)
Jazz , 5dr Hatch Oct 08-+
EU
50 kgs (110 lbs)
50 kgs (110 lbs)
2

FittingKit
K446
EN
First Time Installation
Remove parts from inside the package and
check. Contact your dealer if any parts are
missing or damaged.
This kit fits type A, B, C and D.
These instructions show type A crossbar
fitted. They also apply to type B, C and D.
NOTE: Clamp images in these instructions may
not be representative of the clamps in this kit
3

FittingKit
K446
EN
Use keys to remove covers.
Use hex screwdriver to reverse adjusting
screw 10 turns.
Press adjusting screw and pull crossbar legs
out. Refer to the crossbar instructions for
crossbar adjustment.
Ensure each end of the crossbar is adjusted
equally.
4

FittingKit
K446
EN
Remove locking screw.
Apply protective strip as shown.
Trim if required.
Letters refer to the part numbers stamped on
clamps.
Clamp Part Number:
A = 600A
B = 601A
5

FittingKit
K446
EN
Attach clamp to each leg. NOTE; clamps
may have labels showing their positions on
the vehicle (For example; "Front Right").
Refit locking screw so that it goes through
the hole in the clamp. Do not begin to tighten
the locking screw.
Refer to the underside of the pad for the part
number.
6

FittingKit
K446
EN
Letters refer to the pad part numbers and
position.
Pad Part Number:
A = 11-04-257
B = 11-04-256
C = 11-04-243
Fit rubber pads (supplied with fitting kit) to
foot. Pad may vary in shape to that shown.
Make sure the pad fits into the holes
underneath the foot.
7

FittingKit
K446
EN
Fitment
Place crossbar on vehicle. Minimum
recommended spacing between the bars is
700mm (27 1/2") (unless otherwise stated).
Clamps directly to edge of roof under the
doors
Please check the rear of this manual for
information relating specifically to your
vehicle.
Adjust the legs on the crossbar so that they
are positioned equally from the ends of the
crossbar, and the clamps engage firmly on
the body work of the vehicle.
Tighten adjusting screw to 5 Nm (3.7 ft lb).
8

FittingKit
K446
EN
Tighten locking screw on both legs evenly.
Check crossbar is securely attached to the
vehicle.
Use keys to fit and lock covers
9

FittingKit
K446
EN
CAUTION: Recheck all fasteners immediately
after a load is applied to the crossbars.
Regularly check screws are tight.
10