TrailFX A7057S User manual

www . T r a il F X . c om
Page 1of 7 Rev 031318
PARTS LIST:
Qty
Part Description
Qty
Part Description
1
Driver/Left Sidebar
18
8mm-1.25 x 30 Hex Bolts
1
Passenger/Right Sidebar
24
8mm x 24mm x 2mm Flat Washers
1
Driver Front Mounting Bracket
12
8mm Lock Washers
1
Passenger Front Mounting Bracket
6
8mm Hex Nuts
2
Driver Center/Rear Mounting Brackets
6
8mm Nylon Lock Nuts
2
Passenger Center/Rear Mounting Brackets
12
8mm-1.25 x 25mm Combination Hex Bolts
3
Support Brackets (DS Front & PS Center/Rear)
12
6mm x 25mm Hex Bolts
3
Support Brackets (PS Front & DS Center/Rear)
24
6mm x 22mm x 2mm Flat Washers
6
8mm Nut/Bolt Plates
12
6mm Nylon Lock Nuts
6
8mm Plastic Retainers
5'' Oval Straight Side Bar
Part No. A7057S/B
Fits: 2010-Current Dodge Ram 2500/3500 Mega Cab
Passenger/Right Rear and
Center Mounting Brackets
(6) 8mm Bolt x 8mm Nut Plates
Passenger/Right Front Support Bracket
Driver/Left Center and Rear
Mounting Brackets
Front
(6) Plastic Retainers
Driver/Left Front Support Bracket
Driver/Left Front
Mounting Bracket
Passenger/Right
Center and Rear
Support Brackets
Driver/Left Center
and Rear Support
Brackets
Passenger/Right
Front Bracket
Note front step
pad is closer to
front end of tube
ASSISTANCE IS RECOMMENDED.
REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT.
READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION.
DO NOT OVER TORQUE.STANDARD OPERATING LOAD FOR TIGHTEN
BODY MOUNT NUTS & BOLTS VARIES FROM
45
TO
65
FOOT POUND.
60-180 min
[e-mail]
1 866 638 4870
POLISHED STAINLESS STEEL –LIMITED LIFETIME
POWDER COATED BLACK –3 YEARS
Cutting Not
Required
Drilling
Required

www . T r a il F X . c om
Page 2of 7 Rev 031318
INSTALLATION PROCEDURE:
1. DRILLING MAY BE REQUIRED.
2. Starting at the driver side-front of the vehicle, remove the sealing tape covering the factory holes in the side of the inner
panel, (Figure 1).
3. Determine the correct procedure to attach the driver side front Bracket for your model/year:
Models without factory threaded inserts in body panel:
a. Partially thread an 8mm Hex Bolt into the threaded end of an 8mm Bolt and Nut Plate, (Figure 2). Thread the
Hex Bolt in until it is flush with the welded nut, (Figure 3). Use the Hex Bolt as a handle and insert the Bolt and
Nut Plate into the oval hole, (Figure 4). Feed the threaded bolt on the Bolt Plate through one of the hex
shaped factory holes. Thread (1) 8mm Plastic Retainer onto the threaded end and down tight against the body
panel, (Figure 5). NOTE: The Plastic Retainer is designed to keep the Bolt/Nut Plate from falling into the body
panel and to aid in Bracket installation.
(Fig 3) Thread (1) 8mm Hex Bolt
into the nut on the plate. Stop when
bolt reaches end of nut as pictured
Front
(Fig 1) 2009-mid 2015 Driver/Left front
mounting location (No factory holes
in pinch weld 2009-2012 models)
(Fig 4) Use the loose Hex Bolt as a handle. Insert the
Bolt Plate into the oval hole and feed the threaded
end out either factory hex shaped hole. IMPORTANT:
Do not let go of the hex bolt until after Plastic
Retainer has been threaded onto bolt (Fig 5)
(Fig 5) Thread Plastic Retainer onto Bolt
Plate to hold Bole Plate in position.
Plastic Retainer
(Fig 2) 8mm Bolt-8mm Nut Plate, NOTE:
8mm Bolt-Nut Plate is not required on
models with threaded inserts

www . T r a il F X . c om
Page 3of 7 Rev 031318
b. Select the driver side front Mounting Bracket, (Figure 6). Attach the Bracket to the threaded end of the Bolt
Plate with (1) 8mm Flat Washer, (1) 8mm Lock Washer and (1) 8mm Hex Nut, (Figure 7). Do not tighten at
this time.
c. Remove the 8mm Hex Bolt from the nut on the Bolt Plate from Step 3a. Rotate the Bolt on the Bolt Plate until the
threaded nut lines up with the remaining hole in the Mounting Bracket and body panel, (Figures 7 & 8). Attach
the Bracket to the threaded Nut Plate with (1) 8mm x 30mm Hex Bolt, (1) 8mm Lock Washer and (1) 8mm Flat
Washer, (Figure 8). Do not fully tighten hardware at this time.
Models with factory threaded inserts:
a. Attach the driver side Front Bracket to the threaded inserts with (2) 8mm x 30mm Hex Bolts, (2) 8mm Lock
Washers and (2) 8mm Flat Washer, (Figures 9 & 10). Leave hardware loose.
(Fig 6) Driver side front Bracket
Front
(Fig 7) Attach Bracket to Bolt Plate
Front
Remove Hex Bolt, rotate Bolt/Nut Plate
to line up threaded nut with body panel
and Mounting Bracket (see arrow)
8mm Flat Washer
8mm Lock Washer
8mm Hex Nut
Front
(Fig 8) Attach Bracket to threaded end of
Bolt Plate first. Remove 8mm Hex Bolt
(see Fig 3). Rotate Bolt Plate to line up
with remaining factory hex shaped hole.
8mm Hex Bolt
8mm Lock Washer
8mm Flat Washer
Plastic Retainer
Front
(Fig 9) Driver side front mid 2015-on, an example of
models with factory installed threaded inserts
(Fig 10) Driver side front-models with factory
installed threaded inserts. Bolt Plate not required
Front
(2) 8mm Hex Bolts
(2) 8mm Lock Washers
(2) 8mm Flat Washers

www . T r a il F X . c om
Page 4of 7 Rev 031318
4. Next, select the driver side front Support Bracket. Attach the Bracket to the front facing side of the front Bracket with (1)
8mm x 30mm Hex Bolt, (2) 8mm Flat Washers and (1) 8mm Nylon Lock Nut, (Figure 11). Rotate the Support Bracket to
the back of the pinch weld. Line up the slots in the top of the Support Bracket with the (2) factory holes in the pinch weld.
Attach the Bracket to the back of the pinch weld with (2) 6mm x 25mm Hex Bolts, (4) 6mm Flat Washers and (2) 6mm
Nylon Lock Nuts, (Figures 12 & 13). Do not fully tighten hardware at this time. IMPORTANT: 2009-10 models are not
equipped with factory holes and will require drilling through the pinch weld to attach the Support Bracket. Do not drill
through pinch weld at this time, (see Step 8).
5. Move along the side of the body panel to the center mounting location, (Figure 14). Repeat the appropriate Step 3 to
install the driver side center Bracket, (Figures 15 & 16). IMPORTANT: The front bracket is different from the center and
rear Mounting Brackets, (see illustration above-note direction of mounting plate). Select (1) driver side center/rear Support
Bracket. Repeat Step 4 to attach the Support Bracket to the back of the center bracket and holes, (if equipped), in the
pinch weld, (Figures 16 & 20).
Front
(Fig 13) Driver side front Bracket assembly
(2) 6mm Hex Bolts
(4) 6mm Flat Washers
(2) 6mm Nylon Lock Nuts
(Fig 12) Attach Support Bracket to back of pinch
weld (models with factory holes in pinch weld only)
Front
(2) 6mm Hex Bolts
(4) 6mm Flat Washers
(2) 6mm Nylon Lock Nuts
(Fig 11) Attach Driver/Left front Support Bracket
to front facing side of Mounting Bracket
Front
8mm Hex Bolt
(2) 8mm Flat Washers
8mm Nylon Lock Nut
(Fig 14) Driver/Left center location
Front
Front
(Fig 15) Attach Driver/Left center Bracket

www . T r a il F X . c om
Page 5of 7 Rev 031318
6. Move to the rear location, (Figure 17). Repeat Step 5 to install the rear Mounting Bracket, (Figure 18).
7. Select the driver/left Sidebar. Carefully position the Sidebar onto the (3) Mounting Brackets. IMPORTANT: Do not slide,
(front to back or rotate), the Sidebar on the Brackets or damage to the finish on the Sidebar may result. Attach the Sidebar
to the (3) Brackets with (6) 8mm Combination Hex Bolts, (Figures 19—21). Do not fully tighten at this time.
Front
(Fig 16) Attach Driver/Left Support Bracket
to back of Center Mounting Bracket
IMPORTANT: 2009-2012 models without holes
in pinch weld will require drilling 1/4” holes
through pinch weld to attach driver side front
support bracket. Do complete installation of
sidebars first, level sidebar before drilling
holes for support bracket.
(Fig 17) Driver/Left rear mounting location
Rear
(Fig 18) Driver/Left rear Mounting Bracket assembly
Rear
(Fig 19) Driver/Left front Mounting Brackets
Front
(Fig 20) Driver/left center Bracket assembly
Front
(2) 8mm Combo
Hex Bolts