Thermo Scientific Masterflex P/S 965-0000 User manual

OOPPEERRAAIINNGG MMAANNUUAALL
HHIIGGHH--PPEERRFFOORRMMAANNCCEE
PPUUMMPP HHEEAADD
MMooddeell 996655--00000000
A-1299-7002
Edition 02
Thermo Fisher Scientific
1-800-637-3739 (U.S. nd C n d only)
11 [phone] (Outside U.S.) •[phone] (Loc l)
www.thermo.com •b r.b rn [e-mail]

EEXXPPLLAANNAAIIOONN OOFF SSYYMMBBOOLLSS
CCAAUUIIOONN::Risk of danger. Consult the Operator's Manual for
nature of hazard and corrective actions.
CCAAUUTTIIOONN::Risk of crushing. Keep fingers away from rotor while
pump is in operation. Stop pump before loading or unloading tubing.
2
WARNING: urn off drive before removing or installing tubing.
Fingers or loose clothing could be caught in the rollers.
NNOOEE::Use only MASTE FLEX precision tubing with MASTE FLEX pumps to
ensure optimum performance. Use of other tubing may void applicable
warranties.
WWAARRNNIINNGG:: PPRROODDUUCC UUSSEE LLIIMMIIAAIIOONN
This product is not designed for, nor intended for use in, patient-connected
applications, including, but not limited to, medical and dental use, and,
accordingly, has not been submitted for FDA approval.
C-FLEX — eg TM Consolidated Polymer Technologies, Inc.
MAS ERFLEX — eg TM Cole-Parmer
NORPRENE, PHARMED, YGON — eg TM Saint-Gobain Performance Plastics Corp.
rademarks bearing the ® symbol in this publication
are registered in the U.S. and in other countries.
SSAAFFEEYY PPRREECCAAUUIIOONNSS

3
SSPPEECCIIFFIICCAAIIOONNSS
ypical Flow, Pressure and Vacuum Data:
Flow rat (cw) Discharg Pr ssur * Vacuum* Suction Lift*
Tubing @ 1 rpm @ 100 rpm @ 600 rpm Continuous Int rmitt nt @ 600 rpm @ 600 rpm
mL/min mL/min mL/min psig (bar) psig (bar) in (mm) Hg ft (m) H20
16HP** .9 90 — 100 (6.8) 125 (8.5) — —
15HP** 1.7 170 — 80 (5.5) 100 (6.8) ——
15 1.8 — 1100 25 (1.7) 40 (2.7) 26 (660) 29 (8.8)
24 3.0 — 1800 25 (1.7) 40 (2.7) 26 (660) 29 (8.8)
35 4.3 — 2600 20 (1.4) 35 (2.4) 26 (660) 29 (8.8)
36 5.8 — 3400 15 (1.0) 20 (1.4) 24 (610) 27 (8.3)
Numb r of roll rs: 3
Occlusion: Fixed
Maximum pump sp d (rpm): 600
Nominal torqu load—Running: up to 180 oz-in (13 kg•cm)
Housing mat rials: Stainless steel (SS), polyester (PE) body,
polyphenylene sulfide (PPS) tubing bed,
polypropylene (PP) knob
Roll r/b aring mat rials: Stainless Steel (SS)/Sealed Stainless Steel
Rotor mat rials: Stainless Steel (SS)
Op rating T mp ratur ‡:32°F to 104°F (0°C to 40°C)
Storag T mp ratur : –40°F to 149°F (–40°C to 65°C)
Humidity: 5% to 95% (non-condensing)
Dim nsions (W
× H × D):
perating: 3.7 in
× 3.5 in × 3.0 in (94 mm × 89 mm × 76 mm)
pen: 4.5 in
× 3.5 in × 5.1 in (114 mm × 89 mm × 130 mm)
W ight: 2.1 lb (0.96 kg)
* As tested with N RPRENE®, PHARMED®BPT, and TYG N®tubing.
Values will be less with silicone and C-FLEX®.
**15HP and 16HP tubing are for use only with the MASTERFLEX P/S High-Performance Pump Head
and any MASTERFLEX P/S 1 to 100 rpm drive capable of running two or more Pump Heads.
‡Use in this temperature range for continuous duty operation with no decrease in performance or product life.
Pump Heads will work outside this range with some possible reductions in performance or product life.
Pump H ad Numb r Pump Mat rial Occlusion Shaft L ngth Tubing
965-0000 PPS/PE/SS Fixed Short 15, 24, 35, 36

4
FFiigguurree 11.. MMoouunnttiinngg HHoolleess
IINNRROODDUUCCIIOONN
The MASTE FLEX P/S High-Performance Pump Head delivers in excess of
3 L/min flow at normal MASTE FLEX operating speeds and pressures. It is
designed for optimal pumping in the clockwise direction. There are two mounting
positions. Tubing entry and exit are either on the left side or on top of the pump
when mounted on a MASTE FLEX P/S Drive. The pump will operate with any
MASTE FLEX P/S drive with 180 oz-in (13 kg•cm) or more output torque.
SSEEUUPP AANNDD OOPPEERRAAIIOONN
Pump Dri e Compatibility
The High-Performance Pump Head has a standard shaft interface to
accommodate MASTE FLEX P/S Pump Drives. Pump drive must provide
180 in-oz (13 kg•cm) torque. (NO E: These drives are usually designated as
capable of driving two or more pump heads.)
Mounting Pump Head to Drive
1. Check that pump drive is turned OFF.
2. Align pump shaft tang with slot in motor shaft.
3. If pump drive has alignment pins, slide pump head alignment holes over
pins.
4. Secure pump to pump drive with the two mounting screws (furnished).
a. For left side tubing entry and exit, use round mounting holes.
(Labeled "A" in Figure 1.)
b. For top tubing entry and exit, use hexagonal mounting holes.
(Labeled "B" in Figure 1.)
Selecting ubing
Pumps accept only 15, 24, 35 and 36 tubing. Use only MASTE FLEX tubing that
is surface-printed with the tubing designation.
A
A
B
B

Loading ubing
WARNING: urn off drive before removing or installing tubing. Fingers
or loose clothing could be caught in the rollers.
1. otate tubing retainer knob, Figure 2, counterclockwise to release retainer,
then pull to open cover.
2. Lift latch to open occlusion bed.
FFiigguurree 22.. HHiigghh--PPeerrffoorrmmaannccee PPuummpp HHeeaadd
5

6
3. Insert the MASTE FLEX tubing inside tubing guide and around rotor with
the ends of the tubing extending out of the tubing entrance and tubing exit
as shown in Figure 3. Center tubing on roller.
4. Press the occlusion bed against the tubing, and snap the latch closed.
5. Close the cover, then pull the tubing snug (do not stretch) around the rotor
assembly. Tighten the tubing retainer by rotating the tubing retainer knob
clockwise sufficiently to prevent the tube from moving. Pump is now ready
for operation.
FFiigguurree 33.. LLooaaddiinngg uubbiinngg
Operation
1. Connect pump tubing to desired source and destination.
2. Start pump drive and set desired speed.

MMAAIINNEENNAANNCCEE
Maintenance is limited to replacement of the parts listed in the replacement
parts list and cleaning the pump head.
Replacement Parts
REF DESCRIPTION ORDER NUMBER
ARotor Assembly with Clip 77250-69
B Tubing Ret iner Kit 77250-66
C Occlusion Bed Assembly Kit 77250-67
D Mounting Screws (not shown) 77250-01
FFiigguurree 44.. EExxppllooddeedd VViieeww ooff PPuummpp
Cleaning Pump Head
Use mild detergent with water to clean the pump and rotor assembly. Do not
immerse nor use excessive fluid.
7
B
A
C

8
WARRANTY
This product is warranted against defects in material or workmanship, and at
the option of the manufacturer or distributor, any defective product will be
repaired or replaced at no charge, or the purchase price will be refunded to the
purchaser, provided that: (a) the warranty claim is made in writing within the
period of time specified on this warranty card, (b) proof of purchase by bill of
sale or receipted invoice is submitted concurrently with the claim and shows
that the product is within the applicable warranty period, and (c) the purchaser
complies with procedures for returns set forth in the general terms and
conditions contained in the manufacturer's or distributor's most recent catalog.
This warranty shall not apply to: (a) defects or damage resulting from: (i) misuse
of the product, (ii) use of the product in other than its normal and customary
manner, (iii) accident or neglect, (iv) improper testing, operation, maintenance,
service, repair, installation, or storage, (v) unauthorized alteration or
modification, or (b) post-expiration dated materials.
THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE PURCHASER, AND THE
MANUFACTURER AND DISTRIBUTOR DISCLAIM ALL OTHER WARRANTIES,
WHETHER EXPRESS, IMPLIED, OR STATUTORY, INCLUDING WITHOUT
LIMITATION, WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE. NO EMPLOYEE, AGENT, OR REPRESENTATIVE OF THE
MANUFACTURER OR DISTRIBUTOR IS AUTHORIZED TO BIND THE
MANUFACTUREROR DISTRIBUTOR TO ANY OTHER WARRANTY. IN NO EVENT
SHALL THE MANUFACTURER OR DISTRIBUTOR BE LIABLE FOR INCIDENTAL,
INDIRECT, SPECIAL OR CONSEQUENTIAL DAMAGES.
The warranty period for this product is two (2) years from date of purchase.
RETURN OF ITEMS
To limit charges and delays, contact the seller or Manufacturer for authorization
and shipping instructions before returning the product, either within or outside
of the warranty period. When returning the product, please state the reason for
the return. For your protection, pack the product carefully and insure it against
possible damage or loss. Any damages resulting from improper packaging are
your responsibility.
TECHNICAL ASSISTANCE
If you have any questions about the use of this product, contact the
Manufacturer or authorized seller.
Printed in U.S.A.
Thermo Fisher Scientific
1-800-637-3739 (U.S. and Canada only)
11 [phone] (Outside U.S.)
[phone] (Local)
www.thermo.com
[e-mail]