thomann Stairville BS-280 R10 BeamSpot User manual

BS-280 R10 BeamSpot
moving head
user manual

Musikhaus Thomann
Thomann GmbH
Hans-Thomann-Strasse 1
96138 Burgebrach
Germany
Telephone: [phone]
E-mail: [email protected]
Internet: www.thomann.de
31.03.2017, ID: 399585

Table of contents
1 General notes............................................................................................................................ 4
1.1 Further information........................................................................................................ 4
1.2 Notational conventions................................................................................................. 4
1.3 Symbols and signal words........................................................................................... 4
2 Safety instructions................................................................................................................. 6
3 Features....................................................................................................................................... 9
4 Installation.............................................................................................................................. 10
5 Starting up............................................................................................................................... 12
6 Connections and controls................................................................................................ 13
7 Operating................................................................................................................................. 16
7.1 Starting the device....................................................................................................... 16
7.2 Main menu...................................................................................................................... 16
7.3 Calibration....................................................................................................................... 18
7.4 Menu overview.............................................................................................................. 19
7.5 Gobos................................................................................................................................ 19
7.6 Functions in 15-channel DMX mode..................................................................... 20
7.7 Functions in 21-channel DMX mode..................................................................... 24
8 Maintenance........................................................................................................................... 31
8.1 Installing / replacing the light source.................................................................... 31
9 Cleaning.................................................................................................................................... 33
10 Troubleshooting................................................................................................................... 34
11 Technical specifications.................................................................................................... 35
12 Plug and connection assignments............................................................................... 36
13 Protecting the environment........................................................................................... 37
Table of contents
BS-280 R10 BeamSpot
3

1 General notes
This manual contains important instructions for the safe operation of the unit. Read
and follow the safety instructions and all other instructions. Keep the manual for
future reference. Make sure that it is available to all those using the device. If you sell
the unit please make sure that the buyer also receives this manual.
Our products are subject to a process of continuous development. Thus, they are
subject to change.
1.1 Further information
On our website (www.thomann.de) you will find lots of further information and
details on the following points:
Download This manual is also available as PDF file for you to download.
Keyword search Use the search function in the electronic version to find the
topics of interest for you quickly.
Online guides Our online guides provide detailed information on technical
basics and terms.
Personal
consultation For personal consultation please contact our technical hotline.
Service If you have any problems with the device the
customer service will gladly assist you.
1.2 Notational conventions
This manual uses the following notational conventions:
The letterings for connectors and controls are marked by square brackets and italics.
Examples: [VOLUME] control, [Mono] button.
Texts and values displayed on the device are marked by quotation marks and italics.
Examples: ‘24ch’, ‘OFF’.
1.3 Symbols and signal words
In this section you will find an overview of the meaning of symbols and signal words
that are used in this manual.
Letterings
Displays
General notes
moving head
4

Signal word Meaning
DANGER! This combination of symbol and signal word indicates
an immediate dangerous situation that will result in
death or serious injury if it is not avoided.
WARNING! This combination of symbol and signal word indicates
a possible dangerous situation that can result in death
or serious injury if it is not avoided.
CAUTION! This combination of symbol and signal word indicates
a possible dangerous situation that can result in minor
injury if it is not avoided.
NOTICE! This combination of symbol and signal word indicates
a possible dangerous situation that can result in mate‐
rial and environmental damage if it is not avoided.
Warning signs Type of danger
Warning – high-voltage.
Warning – hot surface.
Warning – dangerous optical radiation.
Warning – suspended load.
Warning – danger zone.
General notes
BS-280 R10 BeamSpot
5

2 Safety instructions
This device is intended to be used as moving-head spotlight. The device is designed
for professional use and is not suitable for use in households. Use the device only as
described in this user manual. Any other use or use under other operating conditions
is considered to be improper and may result in personal injury or property damage.
No liability will be assumed for damages resulting from improper use.
This device may be used only by persons with sufficient physical, sensorial, and intel‐
lectual abilities and having corresponding knowledge and experience. Other persons
may use this device only if they are supervised or instructed by a person who is
responsible for their safety.
DANGER!
Danger for children
Ensure that plastic bags, packaging, etc. are disposed of properly and
are not within reach of babies and young children. Choking hazard!
Ensure that children do not detach any small parts (e.g. knobs or the
like) from the unit. They could swallow the pieces and choke!
Never let children unattended use electrical devices.
DANGER!
Electric shock caused by high voltages inside
Within the device there are areas where high voltages may be present.
Completely disconnect the device from the power supply before you
open or remove covers. Mount all covers and attach them firmly before
connecting the device again.
Do not use the device if covers, protectors or optical components are
missing or damaged.
DANGER!
Electric shock caused by short-circuit
Always use proper ready-made insulated mains cabling (power cord)
with a protective contact plug. Do not modify the mains cable or the
plug. Failure to do so could result in electric shock/death or fire. If in
doubt, seek advice from a registered electrician.
Intended use
Safety
Safety instructions
moving head
6

WARNING!
Eye damage caused by high light intensity
The lamp used in this device produces an intense beam of visible and
invisible light radiation.
Do not start the operation of the device without completely fixed
covers. Never look directly into the light source.
WARNING!
Risk of epileptic shock
Strobe lighting can trigger seizures in photosensitive epilepsy. Sensitive
persons should avoid looking at strobe lights.
WARNING!
Risk of burns at the surface and inside of the device
The surface and the inner parts of the device can become very hot
during operation.
After switching off the device wait for at least 15 minutes before you
start any maintenance activities.
CAUTION!
Risk of injury due to movements of the device
The head of the device can move quickly (pan, tilt) and can produce
very bright light. This is also valid immediately after you turn on the
device, when the device operates in automatic mode or under remote
control and when you turn off a DMX controller that is connected to the
device. Persons staying near the device could be injured or frightened.
Before you turn on the device and during the operation, always ensure
that nobody stays close to the device. If work has to be performed in the
area of movement or in the near vicinity of the device, it must remain
turned off.
NOTICE!
Risk of fire
Do not block areas of ventilation. Do not install the device near any
direct heat source. Keep the device away from naked flames.
Safety instructions
BS-280 R10 BeamSpot
7

NOTICE!
Operating conditions
This device has been designed for indoor use only. To prevent damage,
never expose the device to any liquid or moisture. Avoid direct sunlight,
heavy dirt, and strong vibrations.
NOTICE!
Power supply
Before connecting the device, ensure that the input voltage (AC outlet)
matches the voltage rating of the device and that the AC outlet is pro‐
tected by a residual current circuit breaker. Failure to do so could result
in damage to the device and possibly injure the user.
Unplug the device before electrical storms occur and when it is unused
for long periods of time to reduce the risk of electric shock or fire.
NOTICE!
Possible staining
The plasticiser contained in the rubber feet of this product may possibly
react with the coating of your parquet, linoleum, laminate or PVC floor
and after some time cause permanent dark stains.
In case of doubt, do not put the rubber feet directly on the floor, but use
felt-pad floor protectors or a carpet.
Safety instructions
moving head
8

3 Features
The moving head is particularly suitable for professional lighting tasks, for example at
events, on rock stages, in theatres and musicals or in discotheques.
Special features of the device:
nControl via DMX (15 or 21 channels) and via buttons and display on the unit
nColour wheel with 13 indexable colours, split colours and white
nTwo gobo wheels (one with 14 static gobos, one with 9 freely indexable and
rotatable gobos), variable rotation speed and direction
nFour additional gobos included in the scope of delivery
nTwo rotating and indexable effect prisms (8 round facets, 5 linear facets)
nFrost filter
nMotorised zoom, motorised focus
nLight source included in scope of delivery
Features
BS-280 R10 BeamSpot
9

4 Installation
Unpack and carefully check that there is no transportation damage before using the
unit. Keep the equipment packaging. To fully protect the device against vibration,
dust and moisture during transportation or storage use the original packaging or
your own packaging material suitable for transport or storage, respectively.
You can install the device standing or hanging. When in use, the device must be
mounted at a solid surface or clamped to an approved truss.
Work from a stable platform whenever you install or move the device or when you
perform any kind of maintenance. Block access under the work area.
WARNING!
Risk of injury caused by falling objects
Make sure that the installation complies with the standards and rules
that apply in your country. Always secure the device with a secondary
safety attachment, such as a safety cable or a safety chain.
CAUTION!
Risk of injury due to movements of the device
The head of the device can move quickly (pan, tilt) and can produce
very bright light. This is also valid immediately after you turn on the
device, when the device operates in automatic mode or under remote
control and when you turn off a DMX controller that is connected to the
device. Persons staying near the device could be injured or frightened.
Before you turn on the device and during the operation, always ensure
that nobody stays close to the device. If work has to be performed in the
area of movement or in the near vicinity of the device, it must remain
turned off.
NOTICE!
Risk of fire and overheating
The distance between the light source and the combustible materials
must be greater than 12 m. The distance to non-combustible materials
must be greater than 2 m.
Provide sufficient ventilation.
The ambient temperature must always be below 104 °F (40 °C).
Installation
moving head
10