thomann Stairville LED Par 64 COB User manual

LED Blinder
2 COB 2×65 W
blinder
user manual

Musikhaus Thomann
Thomann GmbH
Hans-Thomann-Straße 1
96138 Burgebrach
Germany
Telephone: [phone]
E-mail: [email protected]
Internet: www.thomann.de
23.06.2017, ID: 409616

Table of contents
1 Safety instructions..................................................................................................................................... 5
2 Features....................................................................................................................................................... 10
3 Installation.................................................................................................................................................. 11
4 Starting up.................................................................................................................................................. 15
5 Connections and controls................................................................................................................... 17
6 Operating.................................................................................................................................................... 22
6.1 Starting the device........................................................................................................................... 22
6.2 Operating on the unit..................................................................................................................... 22
6.3 Remote control................................................................................................................................. 28
6.4 Menu overview................................................................................................................................. 29
6.5 Functions in 1-channel mode...................................................................................................... 30
6.6 Functions in 2-channel mode 2a................................................................................................ 30
6.7 Functions in 2-channel mode 2b................................................................................................ 31
6.8 Functions in 3-channel mode...................................................................................................... 32
7 Technical specifications....................................................................................................................... 33
Table of contents
LED Blinder 2 COB 2×65 W
3

8 Plug and connection assignments.................................................................................................. 34
9 Cleaning....................................................................................................................................................... 35
10 Protecting the environment.............................................................................................................. 36
Table of contents
blinder
4

1 Safety instructions
This device is intended to be used as an electronic illumination effect using LED technics. The
device is designed for professional use and is not suitable for use in households. Use the
device only as described in this user manual. Any other use or use under other operating con‐
ditions is considered to be improper and may result in personal injury or property damage. No
liability will be assumed for damages resulting from improper use.
This device may be used only by persons with sufficient physical, sensorial, and intellectual
abilities and having corresponding knowledge and experience. Other persons may use this
device only if they are supervised or instructed by a person who is responsible for their safety.
Intended use
Safety instructions
LED Blinder 2 COB 2×65 W
5

DANGER!
Danger for children
Ensure that plastic bags, packaging, etc. are disposed of properly and are not
within reach of babies and young children. Choking hazard!
Ensure that children do not detach any small parts (e.g. knobs or the like) from
the unit. They could swallow the pieces and choke!
Never let children unattended use electrical devices.
DANGER!
Electric shock caused by high voltages inside
Within the device there are areas where high voltages may be present. Never
remove any covers.
There are no user-serviceable parts inside.
Do not use the device if covers, protectors or optical components are missing or
damaged.
Safety
Safety instructions
blinder
6

DANGER!
Electric shock caused by short-circuit
Always use proper ready-made insulated mains cabling (power cord) with a pro‐
tective contact plug. Do not modify the mains cable or the plug. Failure to do so
could result in electric shock/death or fire. If in doubt, seek advice from a regis‐
tered electrician.
WARNING!
Eye damage caused by high light intensity
Never look directly into the light source.
WARNING!
Risk of epileptic shock
Strobe lighting can trigger seizures in photosensitive epilepsy. Sensitive persons
should avoid looking at strobe lights.
Safety instructions
LED Blinder 2 COB 2×65 W
7

NOTICE!
Risk of fire
Do not block areas of ventilation. Do not install the device near any direct heat
source. Keep the device away from naked flames.
NOTICE!
Operating conditions
This device has been designed for indoor use only. To prevent damage, never
expose the device to any liquid or moisture. Avoid direct sunlight, heavy dirt, and
strong vibrations.
Safety instructions
blinder
8

NOTICE!
Power supply
Before connecting the device, ensure that the input voltage (AC outlet) matches
the voltage rating of the device and that the AC outlet is protected by a residual
current circuit breaker. Failure to do so could result in damage to the device and
possibly injure the user.
Unplug the device before electrical storms occur and when it is unused for long
periods of time to reduce the risk of electric shock or fire.
Safety instructions
LED Blinder 2 COB 2×65 W
9

2 Features
The LED-Blinder imitates the dimming and response behaviour and the typical afterglow of a
conventional blinder.
Special features of the device:
n2 × COB LED, each 50 W
nColour temperature: 2700 K
nBeam angle: 70°
nControl via DMX, buttons and display on the unit or via remote control (not included)
nStrobe effect
nSound control
Features
blinder
10

3 Installation
Unpack and carefully check that there is no transportation damage before using the unit. Keep
the equipment packaging. To fully protect the device against vibration, dust and moisture
during transportation or storage use the original packaging or your own packaging material
suitable for transport or storage, respectively.
WARNING!
Risk of injury caused by falling objects
Make sure that the installation complies with the standards and rules that apply
in your country. Always secure the device with a secondary safety attachment,
such as a safety cable or a safety chain.
Installation
LED Blinder 2 COB 2×65 W
11

NOTICE!
Risk of overheating
Always ensure sufficient ventilation.
The ambient temperature must always be below 40 °C (104 °F).
NOTICE!
Use of stands
When mounting the device onto a stand, ensure that the stand is in a safe and
stable position and that the weight of the device does not exceed the maximum
permissible load capacity of the stand.
Installation
blinder
12

NOTICE!
Possible data transmission errors
For error-free operation make use of dedicated DMX cables and do not use ordi‐
nary microphone cables.
Never connect the DMX input or output to audio devices such as mixers or ampli‐
fiers.
You can install the unit in hanging or standing position. When in use, the device must always
be attached to a solid surface or an approved truss. Use the openings provided on the two-
piece bracket for attaching.
Always work from a stable platform whenever installing, moving or servicing the unit. In doing
so, the area underneath the unit must be cordoned off.
The safety-rope must be attached to the bracket.
Mounting options
Installation
LED Blinder 2 COB 2×65 W
13

Please note that this device must not be connected to a dimmer.
Installation
blinder
14

4 Starting up
Create all connections while the device is off. Use the shortest possible high-quality cables for
all connections. Take care when running the cables to prevent tripping hazards.
Starting up
LED Blinder 2 COB 2×65 W
15

Connect the DMX input of the device to the DMX output of a DMX controller or another DMX
device. Connect the output of the first DMX device to the input of the second one, and so on
to form a daisy chain. Always ensure that the output of the last DMX device in the daisy chain
is terminated with a resistor (110 Ω, ¼W).
Connections in DMX mode
Starting up
blinder
16

5 Connections and controls
Front panel
Connections and controls
LED Blinder 2 COB 2×65 W
17

1 Mounting bracket
2 Locking screws for the mounting bracket.
3 LED
Connections and controls
blinder
18

Rear panel
Connections and controls
LED Blinder 2 COB 2×65 W
19

4[POWER IN]
IEC chassis plug for mains connection.
[POWER OUT]
IEC chassis socket for the power supply cable to the next unit.
5 Fuse holder
6[DMX IN]
DMX input.
[DMX OUT]
DMX output
7 Connection socket for the optionally available remote control.
8 Microphone
9 Display with function buttons and indicator LEDs.
[MENU]
Selects an option of the respective operating mode, confirms the set value.
Connections and controls
blinder
20