thomann ROADWORX Lighting Stand 1 User manual

Lighting Stand 1
lighting stand
user manual

Musikhaus Thomann
Thomann GmbH
Hans-Thomann-Straße 1
96138 Burgebrach
Germany
Telephone: [phone]
E-mail: [email protected]
Internet: www.thomann.de
07.07.2021, ID: 442430

Table of contents
1 General information................................................................................................................................. 4
2 Safety instructions..................................................................................................................................... 6
3 Features.......................................................................................................................................................... 8
4 Operating....................................................................................................................................................... 9
5 Technical specications....................................................................................................................... 14
6 Protecting the environment.............................................................................................................. 16
Table of contents
Lighting Stand 1
3

1 General information
This manual contains important instructions for the safe operation of the product. Read and
follow the safety instructions and all other instructions. Keep the manual for future reference.
Make sure that it is available to all those using the product. If you sell the product to another
user, be sure that they also receive this manual.
Our products are subject to a process of continuous development. Thus, they are subject to
change. Please refer to the latest version of the user manual which is ready for download
under www.thomann.de.
In this section you will nd an overview of the meaning of symbols and signal words that are
used in this manual.
Symbols and signal words
General information
lighting stand
4

Signal word Meaning
DANGER! This combination of symbol and signal word indicates an
immediate dangerous situation that will result in death or
serious injury if it is not avoided.
CAUTION! This combination of symbol and signal word indicates a pos‐
sible dangerous situation that can result in minor injury if it
is not avoided.
NOTICE! This combination of symbol and signal word indicates a pos‐
sible dangerous situation that can result in material and
environmental damage if it is not avoided.
Warning signs Type of danger
Warning – danger zone.
General information
Lighting Stand 1
5

2 Safety instructions
This light stand is intended to be used for the stable mounting and height-adjustable posi‐
tioning of spotlights. Use the device only as described in this user manual. Any other use or use
under other operating conditions is considered to be improper and may result in personal
injury or property damage. No liability will be assumed for damages resulting from improper
use.
This device may be used only by persons with sucient physical, sensorial, and intellectual
abilities and having corresponding knowledge and experience. Other persons may use this
device only if they are supervised or instructed by a person who is responsible for their safety.
Safety
DANGER!
Danger for children
Ensure that plastic bags, packaging, etc. are properly disposed of and are not in the reach of babies and young children. Choking
hazard! Ensure that children do not detach any small parts (e.g. knobs or the like) from the product. They could swallow the pieces
and choke! Never let children play unattended with the product.
Intended use
Safety instructions
lighting stand
6

CAUTION!
Danger of tipping when transported under load
If the stand is moved without having removed the installed device, the stand may tip over and cause injuries and property damage.
Remove the installed device before transporting the stand.
CAUTION!
Danger of tipping on unsuitable surfaces
When the speaker stand is installed on soft or uneven ground, the stand may tip over and cause injuries and property damage. Install
the stand only on even and solid surfaces.
CAUTION!
Danger of tipping due to overload
In case of overload, the stand may tip over and cause injuries and property damage. Never exceed the maximum load capacity
specied for the stand.
NOTICE!
Possible staining
The plasticiser contained in the rubber feet of this product may possibly react with the coating of your parquet, linoleum, laminate
or PVC oor and after some time cause permanent dark stains. In case of doubt, do not put the rubber feet directly on the oor, but
use felt-pad oor protectors or a carpet.
Safety instructions
Lighting Stand 1
7

3 Features
Special characteristics:
nMetal construction with crossbar for up to four spotlights
nExtension tubes secured by spring lock buttons
nCrossbar mounting
nSingle truss: 1.20 m
nMaximum weight-bearing capacity: 20 kg
nMinimum height: 1.45 m
nMaximum height: 3.25 m
nWeight: 4.5 kg
Features
lighting stand
8

4 Operating
Unpack and check carefully there is no transportation damage before using the product. Keep
the equipment packaging. To fully protect the product against vibration, dust and moisture
during transportation or storage use the original packaging or your own packaging material
suitable for transport or storage, respectively.
CAUTION!
Danger of tipping when transported under load
If the stand is moved without having removed the installed device, the stand may
tip over and cause injuries and property damage.
Remove the installed device before transporting the stand.
Operating
Lighting Stand 1
9

CAUTION!
Danger of tipping on unsuitable surfaces
When the speaker stand is installed on soft or uneven ground, the stand may tip
over and cause injuries and property damage.
Install the stand only on even and solid surfaces.
CAUTION!
Danger of tipping due to overload
In case of overload, the stand may tip over and cause injuries and property
damage.
Never exceed the maximum load capacity specied for the stand.
Operating
lighting stand
10

NOTICE!
Possible staining
The plasticiser contained in the rubber feet of this product may possibly react
with the coating of your parquet, linoleum, laminate or PVC oor and after some
time cause permanent dark stains.
In case of doubt, do not put the rubber feet directly on the oor, but use felt-pad
oor protectors or a carpet.
Comply with regulations
When installing and operating, make sure to follow the standards and regulations
that apply in your country.
Operating
Lighting Stand 1
11

1. Unfold the feet of the tripod until the cross braces are in a horizontal position.
2. Fix this position with the safety screw on the slider to which the three feet are attached.
3. Loosen the locking screw of the crossbar, place the crossbar on the tripod mounting and
tighten it with the locking screw.
4. Loosen the two screws on the extension tubes.
5. Pull out the upper locking screw and pull out the upper extension tube to the required
height and let the locking pin of the locking screw engage in the corresponding grid
perforation.
6. Fix the position of the upper extension tube with the safety screw on the upper tube
clamp.
7. Pull out the lower locking screw and pull out the lower extension tube to the required
height and let the locking pin of the locking screw engage in the corresponding grid
perforation.
8. Fix the position of the lower extension tube with the safety screw on the lower tube
clamp.
9. Attach up to four spotlights to the crossbar. Observe the instructions of the respective
manufacturers. The maximum load capacity of 20 kg in total must not be exceeded.
Setup
Operating
lighting stand
12

1. Remove the spotlight(s).
2. Loosen the safety screw on the lower tube clamp.
3. Pull out the locking screw, slide the lower extension tube all the way down and let the
locking pin of the locking screw engage in the corresponding grid perforation.
4. Fix the position of the lower extension tube with the safety screw on the lower tube
clamp.
5. Loosen the safety screw on the upper tube clamp.
6. Pull out the locking screw, slide the upper extension tube all the way down and let the
locking pin of the locking screw engage in the corresponding grid perforation.
7. Fix the position of the upper extension tube with the safety screw on the upper tube
clamp.
8. Loosen the safety screw of the crossbar and detach the crossbar.
9. Loosen the safety screw on the slider to which the three feet are attached.
10. Fold up the feet of the tripod.
11. Pack all parts of the system in their original package, as possible, and store the package
in a dry place protected against moisture.
Dismounting
Operating
Lighting Stand 1
13

5 Technical specications
Height, max. 3.25 m
Adjustable tripod height 1,45 m … 3,25 m
Footprint Æ1.08 m
Tripod tube diameter Æ41 mm
Tube diameter extension tubes Æ38 mm
Æ35 mm
Dimensions crossbar (B × H × T) 1200 mm × 20 mm × 40 mm
Mounting slots 4
Holder type Æ35 mm tube end
Load, max. (with centric load) 20 kg
Transport dimensions (W × H × D) 200 mm × 1220 mm × 140 mm
Technical specications
lighting stand
14

Weight 4.5 kg
Colour black
Stand type Lighting stand
Incl. crossbar yes
Crank No
Incl. T bar yes
Incl. screws for lamp attachment yes
Further information
Technical specications
Lighting Stand 1
15

6 Protecting the environment
For the transport and protective packaging, environmentally friendly materials have been
chosen that can be supplied to normal recycling.
Ensure that plastic bags, packaging, etc. are properly disposed of.
Do not just dispose of these materials with your normal household waste, but make sure that
they are collected for recycling. Please follow the notes and markings on the packaging.
Disposal of the packaging mate‐
rial
Protecting the environment
lighting stand
16

Notes
Lighting Stand 1
17

Notes
lighting stand
18

Musikhaus Thomann · Hans-Thomann-Straße 1 · 96138 Burgebrach · Germany · www.thomann.de