thomann ROADWORX User manual

Multi Electric Stand
Electric Height-Adjustable Stand
User Manual

Thomann GmbH
Hans-Thomann-Straße 1
96138 Burgebrach
Germany
Telephone: [phone]
Internet: www.thomann.de
11.12.2023, ID: 491963 (V3)

Table of contents
1 General information.............................................................................................................. 5
1.1 Symbols and signal words........................................................................................... 5
2 Safety instructions................................................................................................................. 6
3 Features....................................................................................................................................... 7
4 Assembly..................................................................................................................................... 8
5 Operating elements............................................................................................................ 15
6 Operation................................................................................................................................. 16
7 Technical specications.................................................................................................... 17
8 Troubleshooting................................................................................................................... 18
9 EU Declaration of Conformity........................................................................................ 19
10 Protecting the environment........................................................................................... 20
Table of contents
Multi Electric Stand 3
Electric Height-Adjustable Stand

4Multi Electric Stand
Electric Height-Adjustable Stand

1 General information
This document contains important instructions for the safe operation of the product.
Read and follow the safety instructions and all other instructions. Keep the document
for future reference. Make sure that it is available to all those using the product. If you
sell the product to another user, be sure that they also receive this document.
Our products and documentation are subject to a process of continuous develop‐
ment. They are therefore subject to change. Please refer to the latest version of the
documentation, which is ready for download under www.thomann.de.
1.1 Symbols and signal words
In this section you will nd an overview of the meaning of symbols and signal words
that are used in this document.
Signal word Meaning
DANGER! This combination of symbol and signal word indicates
an immediate dangerous situation that will result in
death or serious injury if it is not avoided.
CAUTION! This combination of symbol and signal word indicates
a possible dangerous situation that can result in minor
injury if it is not avoided.
NOTICE! This combination of symbol and signal word indicates
a possible dangerous situation that can result in mate‐
rial and environmental damage if it is not avoided.
Warning signs Type of danger
Warning – high-voltage.
Warning – danger zone.
General information
Multi Electric Stand 5
Electric Height-Adjustable Stand

2 Safety instructions
This device is intended for use as multifunctional base for stable xing and height-
adjustable installation of keyboards, synthesizers, stage pianos, etc. and is not suit‐
able for lifting persons. Use the device only as described in this user manual. Any
other use or use under other operating conditions is considered to be improper and
may result in personal injury or property damage. No liability will be assumed for
damages resulting from improper use.
This device may be used only by persons with sucient physical, sensorial, and intel‐
lectual abilities and having corresponding knowledge and experience. Other persons
may use this device only if they are supervised or instructed by a person who is
responsible for their safety.
Safety
DANGER!
Risk of injury and choking hazard for children!
Children can suocate on packaging material and small parts. Children can injure themselves when handling the device. Never
allow children to play with the packaging material and the device. Always store packaging material out of the reach of babies and
small children. Always dispose of packaging material properly when it is not in use. Never allow children to use the device without
supervision. Keep small parts away from children and make sure that the device does not shed any small parts (such knobs) that
children could play with.
DANGER!
Danger to life due to electric current!
A short circuit could lead to a re hazard and risk of death. Always use proper ready-made insulated triple-core mains cable with a
safety plug. Do not modify the mains cable or the plug. In case of isolation damage, disconnect immediately the power supply
and arrange repair. If in doubt, seek advice from a qualied electrician.
DANGER!
Danger to life due to electric current!
Within the device there are areas where high voltages may be present. Never remove any covers. There are no user-serviceable
parts inside. Do not use the device when covers, safety equipment or optical components are missing or damaged.
CAUTION!
Risk of injury due to tipping, excessive loading and improper use!
In case of excessive and uneven loading, the product might tip over, causing injury and property damage. The product cannot
hold people. Never sit down on the product. Never exceed the specied maximum load for the product.
CAUTION!
Risk of injury due to tipping of stand on an unsuitable ground!
If the stand is placed on soft or uneven ground, it may overturn and cause injuries and property damage. Place the stand only on
at and solid ground.
NOTICE!
Damage to the device if operated in unsuitable ambient conditions!
The device can be damaged if it is operated in unsuitable ambient conditions. Only operate the device indoors within the
ambient conditions specied in the “Technical specications” chapter of this user manual. Avoid operating it in environments
with direct sunlight, heavy dirt and strong vibrations. Avoid operating it in environments with strong temperature uctuations. If
temperature uctuations cannot be avoided (for example after transport in low outside temperatures), do not switch on the
device immediately. Never subject the device to liquids or moisture. Never move the device to another location while it is in oper‐
ation. In environments with increased dirt levels (for example due to dust, smoke, nicotine or mist): Have the device cleaned by
qualied specialists at regular intervals to prevent damage due to overheating and other malfunctions.
NOTICE!
Possible staining due to plasticiser in rubber feet!
The plasticiser contained in the rubber feet of this product may react with the coating of the oor and cause permanent dark
stains after some time. If necessary, use a suitable mat or felt slide to prevent direct contact between the device’s rubber feet and
the oor.
Intended use
Safety instructions
6Multi Electric Stand
Electric Height-Adjustable Stand

3 Features
Special characteristics:
nElectrical height-adjustable stand for keyboards, synthesizers, stage pianos,
mixers, studio equipment, etc.
nSteplessly height-adjustable from 61 cm (24 in) up to 126 cm (50 in)
nFour heights freely storable
nAdjustable feet to compensate for oor unevenness
nMany adding-on accessories (available separately)
nMaximum load capacity: 150 kg
Features
Multi Electric Stand 7
Electric Height-Adjustable Stand

4 Assembly
When assembling the stand, use felt-pad oor protectors or a carpet in
order to avoid damaging the coating of your parquet, linoleum, laminate or
PVC oor.
Open the package and make sure before assembling that the entire scope of delivery
is present as described here.
1 Control panel
2 Control panel holder
3 4 × Slide screw
4 4 × Round nut
5 8 × Allen screw M6×25
6 2 × Tube
7 2 × Standing column
8 Holder for the controller
9 14 × Allen screw M6×10
10 4 × Adhesive cable tie
11 Controller
12 2 × Cable of the standing column
13 Cable of the control panel
14 2 × Foot
15 Power cable
16 2 × Crossbar
17 4 × Allen screw M6×40
18 4 × Adhesive foam pad
19 2 × Angle piece
20 2 × Allen key
1. Set up the stand near a power wall outlet.
2. Proceed according to the illustrations and only use the supplied screws. Using
dierent screws could reduce the stability of the stand.
Assembly
8Multi Electric Stand
Electric Height-Adjustable Stand

%
#
$
3. First attach the control panel (1) to the control panel holder (2). Use the four
supplied slide screws (3) and the four round nuts (4) and hand-tighten them.
&
'
(
5
4. Position the tubes (6) and standing columns (7) as illustrated. Attach the
mounted control panel holder with two Allen screws M6×25 (5) to the tube (6)
and to the standing column (7) using the Allen key (20). Attach the tube and
the standing column on the other side following the same procedure.
Assembly
Multi Electric Stand 9
Electric Height-Adjustable Stand

)
*
5. Attach the controller holder (8) with four Allen screws M6×10 (9) to both tubes
(6) using the Allen key (20).
+
6. Attach two adhesive cable ties (10) in the illustrated position to properly install
the cable of the control panel.
Assembly
10 Multi Electric Stand
Electric Height-Adjustable Stand

,
. -
-
7. Slide the controller (11) in the holder (8) and connect the cables of the
standing columns (12) and the cable of the control panel (13) to the controller.
/
*
8. Attach the feet (14) with four Allen screws each M6×10 (9) to the standing col‐
umns (7).
Assembly
Multi Electric Stand 11
Electric Height-Adjustable Stand

0
+
9. Attach the two adhesive cable ties (10) in the illustrated position to properly
install the power cable (15). Connect the power cable (15) to the controller (11).
Ensure that the power cable is not installed too tight in the cable ties.
The cable should be able to move when the height is adjusted.
12
34
S
1
2
10. Turn the stand over and put it on its feet.
Attach the crossbars (16) at the desired position to both tubes (6) with two
Allen screws M6×40 each (17) using the Allen key (20).
Assembly
12 Multi Electric Stand
Electric Height-Adjustable Stand

12
34
S
3
11. Attach two adhesive foam pads (18) to each crossbar (16) in the desired posi‐
tions.
12
34
S
*
4
%
12. If required, attach the angle pieces (19) with one Allen screw M6×10 each (9) to
the crossbars (16).
Alternatively, you can attach the devices to be mounted on the stand with a
3/8-inch cylinder head screw each (not included in the scope of delivery) using
the Allen key (20).
Align the control panel (1) as desired and tighten the slide screws (3) and the
round nuts (4).
Assembly
Multi Electric Stand 13
Electric Height-Adjustable Stand

1 2
34
S
13. Align the adjustable feet to compensate uneven ground.
The assembled stand should now look like the following illustration:
12
34
S
Assembly
14 Multi Electric Stand
Electric Height-Adjustable Stand

5 Operating elements
ö # $ %
1 Display
2[1] | [2] | [3] | [4] | Number buttons for storing and selecting a set height
3[5] | Buttons for storing a set height
4| | Buttons for setting the height
Control panel
Operating elements
Multi Electric Stand 15
Electric Height-Adjustable Stand

6 Operation
Unpack and check carefully there is no transportation damage before using the unit.
Keep the equipment packaging. To fully protect the product against vibration, dust
and moisture during transportation or storage use the original packaging or your
own packaging material suitable for transport or storage, respectively.
Press and hold [S] and [3] simultaneously until the display switches.
ðThe display shows the set height in the corresponding unit.
1. Hold down or to set a desired height from 61 cm (24 in) up to 126 cm
(50 in). The motor starts to work and moves the stand in the desired position.
ðThe display shows the set height (e.g. ‘090’ for the height of 90 cm).
2. Release or to apply the setting.
ðThe motor stops.
3. Press [S] and then one of the buttons [1], [2], [3] or [4] to store the set height to
one of the number buttons.
4. Press one of the buttons [1], [2], [3] or [4] at any time to move the stand to the
stored height.
ðThe motor moves the stand automatically to the stored position.
If set heights are not approached correctly after the device has been switched o and
then on again, or if the two columns don’t move synchronously, you have to perform
a reset.
Press and hold until the columns have moved to the lowest position (61 cm /
24 in) and keep pressing for another 5 seconds.
ðThe display shows ‘RST’ . The stand has been reset. The set heights are not
deleted.
Switching between centimetres/
inches
Setting and storing the height
Performing a reset
Operation
16 Multi Electric Stand
Electric Height-Adjustable Stand

7 Technical specications
Adjustable height, min. 61 cm (24 in)
Adjustable height, max. 126 cm (50 in)
Operational speed 3 cm/s (22 s for the whole adjusting range)
Length crossbar 35 cm
Adjustable distances crossbar 16 cm, 26 cm, 36 cm, 46 cm, 56 cm, 66 cm, 76 cm, 86 cm, 96 cm
Feet length 55 cm
Load capacity 150 kg
Power consumption 200 W
Supply voltage 100 - 240 V 50/60 Hz
Dimensions (W × H × D) 1120 mm × 610 mm – 1260 mm × 550 mm
Weight 22 kg
Ambient conditions Temperature range 0 °C…40 °C (32 °C…104 °F)
Relative humidity 20 %…80 % (non-condensing)
Colour Black
Technical specications
Multi Electric Stand 17
Electric Height-Adjustable Stand

8 Troubleshooting
In the following we list a few common problems that may occur during operation.
We give you some suggestions for easy troubleshooting:
Symptom Remedy
‘RST’ A reset was performed. Wait for the display to switch back.
‘ER1’ …‘ER9’ Make sure that the two cables of the standing columns and the cable of the
control panel are undamaged and correctly connected to the controller. If the
error persists, the controller and the motors of the standing columns need to
be checked by the service department.
‘E10’ …‘E12’
‘ERA’ Controller must be checked by the service department.
‘ERF’ Make sure that the mains cable and the cable of the control panel are undam‐
aged and correctly connected. If the error persists, the controller and the
motors of the standing columns need to be checked by the service depart‐
ment.
‘E21’ Perform a reset.
‘E22’ Reduce the load on the stand.
‘E31’ Controller must be checked by the service department.
‘E32’ Switch the device o and then on again. If the error persists, the controller
needs to be checked by the service department.
‘E33’ Controller must be checked by the service department.
‘E34’ Make sure that the cable of the control panel is undamaged and correctly con‐
nected to the controller.
‘A01’ …‘A08’ Make sure that there are no obstacles in the path of the stand when it is
moving.
‘A09’ Perform a reset.
‘HOT’ Wait for 10 minutes for the motor to cool down.
‘Hnd’ Make sure that the cable of the control panel is undamaged and correctly con‐
nected to the controller.
If the procedures recommended above do not succeed, please contact our Service
Center. You can nd the contact information at www.thomann.de.
Troubleshooting
18 Multi Electric Stand
Electric Height-Adjustable Stand

9 EU Declaration of Conformity
Name and address of
manufacturer / EU-AR
Thomann GmbH
Hans-Thomann-Straße 1
96138 Burgebrach
Germany
THIS DECLARATION OF CONFORMITY IS ISSUED UNDER THE SOLE RESPONSIBILITY OF:
Name and address of
manufacturer
Thomann GmbH
Hans-Thomann-Straße 1
96138 Burgebrach
Germany
Product identication 491963 Roadworx Multi Electric Stand
THE PRODUCTS MENTIONED IN THIS DECLARATION ARE IN CONFORMITY WITH:
EU Community Legislation Machinery Directive 2006/42/EC
Restriction of Hazardous Substances (RoHS) Directive 2011/65/EU
Electromagnetic Compatibility (EMC) Directive 2014/30/EU
Harmonised standards Safety of machinery
EN ISO 13857:2019 + EN ISO 13857:2008
EN 60204-1:2006 + A1:2009 + AC:2010 + EN 60204-1:2018
EN ISO 12100:2010
Safety of electrical equipment
EN 60335-1:2012 + AC:2014 + A11:2014 + A13:2017 + A1:2019 + A2:2019 + A14:2019
Exposure of humans to electromagnetic elds (EMF)
EN 12198-1:2000+A1:2008
Electromagnetic Compatibility (EMC)
EN 55014-1:2017 + A11:2020 + EN IEC 55014-1:2021 + EN 55014-1:2006 + A1:2009 + A2:2011
EN 55014-2:2015 + EN IEC 55014-2:2021 + EN 55014-2:1997 + AC:1997 + A1:2001 + A2:2008
EN 61000-3-2:2014 + EN IEC 61000-3-2:2019
EN 61000-3-3:2013 + A1:2019
EN 61000-6-1:2007
EN 61000-6-3:2007 + A1:2011/AC:2012
Restricted substances in electrical products
EN 50581:2012
EN IEC 63000:2018
SIGNED FOR AND ON BEHALF OF:
Place and date of issue Burgebrach, 29 November 2021
EU Declaration of Conformity
Multi Electric Stand 19
Electric Height-Adjustable Stand

10 Protecting the environment
Environmentally friendly materials have been chosen for the packaging. These mate‐
rials can be sent for normal recycling. Ensure that plastic bags, packaging, etc. are dis‐
posed of in the proper manner.
Do not dispose of these materials with your normal household waste, but make sure
that they are collected for recycling. Please follow the instructions and markings on
the packaging.
Observe the disposal note regarding documentation in France.
This product is subject to the European Waste Electrical and Electronic Equipment
Directive (WEEE) as amended.
Do not dispose of your old device with your normal household waste; instead, deliver
it for controlled disposal by an approved waste disposal rm or through your local
waste facility. When disposing of the device, comply with the rules and regulations
that apply in your country. If in doubt, consult your local waste management facility.
Proper disposal protects the environment as well as the health of your fellow human
beings.
Also note that waste avoidance is a valuable contribution to environmental protec‐
tion. Repairing a device or passing it on to another user is an ecologically valuable
alternative to disposal.
You can return your old device to Thomann GmbH at no charge. Check the current
conditions on www.thomann.de.
If your old device contains personal data, delete those data before disposing of it.
Disposal of the packing material
Disposal of your old device
Protecting the environment
20 Multi Electric Stand
Electric Height-Adjustable Stand