Thrustmaster T300 RS User manual

Update: January 2024
T300 RS Racing Wheel
Wake-up method (Bootloader)
T300 RS ; T300 SERVO BASE ; T300 Ferrari GTE ;
T300 Ferrari Integral Alcantara Edition ; T300RS GT Edition
English: My T300 RS will not power on and is not detected or
recognized by my PC or games console - Wake-up method
(Bootloader)
Français : Mon T300 RS ne s’allume pas et n’est pas détecté ni reconnu
par mon PC ou ma console de jeux – Méthode de réveil (Bootloader)

Update: January 2024
Deutsch: Mein T300 RS lässt sich nicht einschalten und wird von
meinem PC oder meiner Spielekonsole nicht erkannt - Wake-up method
(Bootloader)
Español: Mi T300 RS no enciende y mi PC o consola de juegos no lo
detecta ni reconoce - Método de reactivación (Bootloader)
Italiano: Il mio T300 RS non si accende e non viene rilevato o
riconosciuto dal mio PC o dalla mia console di gioco - Metodo di
riattivazione (Bootloader)
Português: Meu T300 RS não liga e não é detectado ou reconhecido
pelo meu PC ou console de jogos - Método de reativação (Bootloader)
Nederlands: Mijn T300 RS gaat niet aan en wordt niet gedetecteerd of
herkend door mijn pc of gameconsole - Wekmethode (Bootloader)
日本語: T300 RS の電源が入らず、PC またはゲーム コンソールで検出また
は認識されません - ウェイクアップ方法 (Bootloader)
简体中文: 我的 T300 RS 无法开机，并且无法被我的电脑或游戏机检测
到或识别 - 唤醒方法 (Bootloader)
한국어: 내T300 RS 가켜지지 않고 PC 나게임 콘솔에서 감지 또는
인식되지 않습니다. - 절전 모드 해제 방법(Bootloader)

Update: January 2024
My T300 RS will not power on and is not detected or recognized by my
PC or games console - Wake-up method (Bootloader)
.
System requirements: PC running Windows® 10 or more recent
In this article we give you the procedure to follow to try to wake up your T300 RS
racing wheel.
Important note:
The wake-up procedure only applies in the specific case whereby the racing wheel
base will not power on
-The racing wheel does not self-calibrate (automatic movements of the
wheel rim from left to right).
-No LEDs light up on the racing wheel’s servo base.
Things to verify before getting started
-It is imperative that a Thrustmaster wheel be mounted on the servo base
of the T300 RS.
-It is imperative to follow the connection instructions.
oThe power plug must be properly plugged into a wall outlet
▪We recommend that you avoid using an extension cord,
power strip or current transformer
oThe racing wheel base will have be directly connected to a USB
port on the PC
▪We recommend that you avoid using a USB hub, a USB
extension, or any other type of connection extension
Tip on connecting the power cable to the back of the servo base.
-Make sure the plug is firmly inserted.

Update: January 2024
1) Make sure that you have installed the latest PC - DRIVERS FORCE
FEEDBACK driver on your PC
If necessary, you will find the driver for your device on our website, in the Drivers
section:
https://support.thrustmaster.com/product/t300rs/
Restart your computer to complete the update.
2) Plug the T300 RS power plug into a wall outlet
-DO NOT CONNECT the racing wheel to your PC’s USB before being
prompted to do so.
3) Make sure your T300 RS is in PC mode
-The sliding switch must be on PC or PS3
4) Simultaneously press and hold the L3 and R3 buttons
5) Connect the T300 RS directly to a PC USB port by holding down the L3 and
R3 buttons
-Wait about 3 seconds then release the L3 and R3 buttons.

Update: January 2024
6) Launch the firmware updating app on your PC.
Click in the Windows search magnifying glass field (located on your PC’s taskbar),
type Firmware Update and then click to launch the app.
7) The "Thrustmaster – Firmware Updater" window appears onscreen
-Device: shows the device in [Boot] mode
-Firmware: displays the firmware version that will be applied to the device

Update: January 2024
Note: If nothing is displayed in the Device or Firmware sections, repeat the
entire procedure from the beginning — but this time connecting the USB
connector to another USB port on your computer (or perform the procedure on
a different computer).
Also, if you have a desktop PC, we recommend using a USB port located on
the back of the central unit.
8) Click OK to carry out the firmware update
9) Wait while the Firmware is updating
-Wait for the Firmware to load
oDO NOT DISCONNECT the racing wheel from the PC's USB port.
oDO NOT UNPLUG the power supply.

Update: January 2024
The firmware updating app will then let you know whether the procedure has been
successful.
The racing wheel self-calibrates (automatic movements of the wheel rim from left to
right), and its LED lights up again.
Click OK then close the Firmware updater.
Note: In the event that this procedure fails, repeat the entire procedure from the
beginning — but this time connecting the USB connector to another USB port
on your computer (or perform the procedure on a different computer).
If the problem persists, please contact our technical support team: they will
provide you with other solutions.
10) Test your T300 RS in the Control Panel
On your keyboard, simultaneously press the Windows and R keys
-The Run window opens: type joy.cpl and then click OK

Update: January 2024
The Game Controllers window opens: select your product’s name, and then click
Properties.
You are now ready to play!

Update: January 2024
Mon T300 RS ne s’allume pas et n’est pas détecté ni reconnu par mon
PC ou ma console de jeux – Méthode de réveil (Bootloader)
.
Système requis : PC avec Windows® 10 ou plus récent
Dans cet article nous vous donnons la procédure à suivre pour tenter de réveiller
votre volant T300 RS.
Attention :
La procédure de réveil s’applique uniquement si la base du volant ne s’allume pas.
-Le volant ne calibre pas (mouvement automatique de la roue de droite à
gauche)
-Aucun voyant ne s'allume sur le servo base
Points à vérifier avant de commencer
-Il est impératif qu’une roue Thrustmaster soit montée sur le servo base
du T300 RS
-Il est impératif de respecter les consignes de branchements
oLa prise de courant devra être directement branchée à une prise
murale
▪Nous recommandons d'éviter l'utilisation de rallonge, de
multiprise ou de transformateur de courant.
oLe volant devra être directement connecté à un port USB du PC
▪Nous recommandons d'éviter l'utilisation de HUB USB, de
rallonge USB et toute extension de branchement.
Conseil au sujet du branchement du câble d’alimentation à l’arrière du servo base
-Assurez-vous que la prise est fermement insérée

Update: January 2024
1) Assurez-vous d’avoir installé sur votre PC le dernier pilote PC - DRIVERS
FORCE FEEDBACK
Si nécessaire vous trouverez le pilote de votre appareil sur notre site, dans la section
Pilotes :
https://support.thrustmaster.com/product/t300rs/
Redémarrez l’ordinateur pour finaliser l’installation.
2) Branchez la prise d’alimentation du T300 RS à une prise murale
-NE CONNECTEZ PAS le volant au port USB de votre PC avant d’être
invité à le faire.
3) Assurez-vous que votre T300 RS est en mode PC
-Le sélecteur doit être sur PC ou PS3
4) Pressez simultanément et maintenez les boutons L3 et R3
5) Connectez le T300 RS directement à un port USB du PC en maintenant les
boutons L3 et R3 appuyés
-Patientez environ 3 secondes puis relâchez les boutons L3 et R3