Tiens B0H-B2 User manual

Hydrogen Water Sprayer
Product Manual
Model: B0H-B2
TIENS
Distributor: Tianjin Tianshi Biological Engineering Co., Ltd.
Address: No.20 Xinyuan Road, Wuqing Development Area, Tianjin, China. Postal Code: 301700.
Website: www.tiens.com.
Manufacturer: Guangzhou Olans Water Treatment Equipments Co., Ltd.
Address: GaoSha Industry Zone, ZhongCun, PanYu, GuangZhou, China. Postal Code: 510000.
Importer: Tiens Europe GmbH, Georg-Wilhelm-Strasse 3, 10711 Berlin, Germany.
Tel.: [phone]. Email: [email protected]. Website: www.tiens.eu.
Distributed by: Tianshi GmbH, Georg-Wilhelm-Str. 3, 10711, Berlin, Germany.
1. Product Structure
Cover
Spray head
Body
Charging port
Electrolysis button

2. Product feature
(1) High efficiency hydrogen production, 1000 ppb hydrogen-rich, high purity.
(2) Negative potential water, -400-0 negative potential, high solubility.
(3) High quality & powerful spray, fast hydration.
3. Precautions
(1) Please use a power adapter with DC5V output voltage, to avoid damaging the product or
prevent potential safety hazards.
(2) Please keep away from high temperatures and fire.
(3) Please do not disassemble or repair the product by yourself, in order to avoid damaging it.
(4) Do not rinse or soak in water directly to avoid water seepage and machine failure.
(5) The device cannot be immersed in water; if water is accidentally poured on the body of the
device it should be wiped clean, to avoid mechanical failure caused by water seepage.
(6) lt is forbidden to use carbonated beverages to produce high-concentration molecular
hydrogen water, because the internal pressure is too high, and may lead to an explosion
hazard.
(7) lt is forbidden to use tea with tea leaves because they will result in mineral tea stains or
other damage.
(8) Applicable water quality and water temperature: In line with the Sanitary Standard for
Drinking Water (GB5749-2006), use warm (below 60°C), purified, clarified mineral water. If the
temperature is too high, it will promote the escape of hydrogen from the water, and can easily
damage the device.
(9) Hydrogen ions, produced by the device and dissolved in water, are inert and will gradually
evaporate from the container into the air. It is therefore recommended that the hydrogen-rich
water should not be stored in the device for too long; instead, it should be used up completely
within 30 minutes. For the purpose of ensuring a high concentration of hydrogen in the water, a
high concentration of molecular hydrogen water should be prepared again, over 30 minutes.
(10) Please clean the device thoroughly, if it hasn’t been used for several days.
(11) Do not clean the device with oily or viscous substances, so the spraying nozzle doesn’t
become blocked.
(12) Do not spray the hydrogen water into eyes.

(13) Do not use sharp objects to clean the device.
(14) Do not clean the device with alcohol and detergents.
4. Content of the package
Hydrogen Water Sprayer
Charging Cable x 1
Product Manual x 1
Quality Certificate x 1
5. Instruction for use
Clean the bottle inside, before using it for the first time. Fill the bottle with lukewarm water
(below 60°C) and soak it for 4 to 8 hours. Next, run the water electrolysis 6 to 8 times, before
regular use.
1. Open the lid and remove the spray head counter-clockwise, fill the bottle with water
and then screw the spray head back in clockwise.
2. Press the button on the bottom of the bottle. The water electrolysis will start. During
the electrolysis, the LED light will start gradually changing colour from blue to red. After
two minutes, the electrolysis will end and the hydrogen-rich water will be ready for use.
If you press the button again during electrolysis, the process will stop.
3. After the electrolysis has stopped, spray your skin with hydrogen-rich water, by
directing the spray nozzle at the part of the body you want to spray and pressing the
spray head.
4. When the device charge is insufficient, the red LED will start blinking.
5. Charge the device for 1-2 hours with the supplied charging cable. While charging, the
red LED light will stay on, slowly blinking from dark to light red. When the device is fully
charged, the light will turn blue.
6. If the device is plugged in during the electrolysis cycle, the LED lights will shine as usual,
gradually changing colour from blue to red.
6. Product technical details
Technical indicators
Parameters
Remarks
Dimensions
32.3x32.3x135.5mm
Capacity
15ml
Battery
4000 mAh Lithium polymer battery

Electrode dimension
Φ21
Body material
Food-grade PC
Electrolysis time
2 minutes
Number of electrolysis cycles
per full charge
20 times
Charging time
1-2 hours
Hydrogen content
1000ppb
OPR (redox potential)
-200-0mV
Charging indicator
Red, slowly pulsing (breathing) light
Full charge indicator
Long, blue light
Low power indicator
Long, red light
No indication
when batter is
out of power
7. Maintenance
Daily cleaning
To clean, wipe the surface of the device with a fresh, wet and soft cleaning cloth. Unscrew the
spray head, fill the bottle half-way with clean, purified water and shake it few times. Pour the
water out and screw the spray head back in.
Regular cleaning
Once in a while, after using the device intensely for a long time, the inside of the device and
possible mineral build-up on the electrodes will need to be cleaned with citric acid.
In order to clean the device, follow the method below:
Pour citric acid with a 5% concentration (dissolve 5 g of citric acid in 100 ml lukewarm water)
into the bottle and soak it for about 20 to 30 minutes, then repeat the daily cleaning, rinsing
the bottle with clean water.
Step 1: measure 5 g of citric acid
Step 2: add 100ml of lukewarm water (40-60°C), stir and dilute completely
Step 3: pour citric acid solution into the bottle
Stap 4: Soak for 20-30 minutes and rinse with clean water

Removing odours
After using the device intensely for a long time, the electrodes may have a hydrogen odour. To
remove it, pour hot, 60°C clean water into the bottle and let it soak for about 5 minutes, then
pour out the water and leave the bottle to dry.
Device failure and possible repair methods
Please check the following, most common causes of device failure and possible repair methods.
If a failure still occurs, please contact a distributor and ask for help.
Failure
Possible cause and a solution:
Problems with
charging
The charger is damaged, and needs to be replaced with a new charger
(5V/1A or 5V/2A)
If the problem still occurs, the battery might be defective or may need
replacement; please contact a distributor and ask for repair or a battery
replacement.
LED light
doesn’t work
The device is out of power and must be charged, before use.
If the device produces bubbles during electrolysis, but the LED light doesn’t
work, it may be damaged. Please contact a distributor and ask for repair.
The device
doesn’t
generate
hydrogen
The device is out of power and must be charged, before use.
If the device hasn’t been used for a long time, the SPE membrane may be
dry. Fill the bottle with lukewarm water (below 60°C) and soak it for 4 to 8
hours.
There may be mineral calcification build-up on the electrodes. Please refer
to the “Regular cleaning” section and follow the instructions.
If the problem still occurs, there may be a malfunction of the electrode or
an internal circuit. Please contact a distributor and ask for repair or a device
replacement.
Leakage of
water from the
bottle
The spray head may not have been screwed on properly. Tighten the spray
head properly.
The seal under the spray head may be old. Please contact a distributor and
ask for a seal replacement.