Timberline Tool FIRETOOLS FF1-S User manual

Instruction Manual
Model FF1-S
Fire Hose Clamp
SAVE these instructions
for future reference.
For your personal safety
READ and UNDERSTAND
instructions before using tools.

© 2008 Timberline Tool All Rights Reserved.
Familiarize yourself with all parts, names, and numbers. Refer to this
diagram for the assembly and operation procedures that follow.
FF1-S DIAGRAM
A1 – Top Jaw / Bottom Handle
A2 – Top Handle
A3 – Bottom Jaw
A4 – Links
A5 - Footpad
$
$
$
$
$
2
SPECIFICATIONS
• e FF1-S is designed for single jacket canvas or synthetic hose
up to 1-3/4” in diameter.
• Rated for 300 psi
Length: 12.0 in 30.5 cm
Width: 4.0 in 10.2 cm
Weight: 1.5 lbs 0.7 kg

GENERAL SAFETY RULES
For all Fire Tools
READ and UNDERSTAND all instructions. Failure to follow all
instructions listed below may result in serious personal injury and/or
damage to the tool.
TIMBERLINE FF1-S
3
INTRODUCTION
Timberline Firefighter Clamps are designed to be used to temporarily stop the
pressurized flow of water in canvas, rubber or synthetic hose without permanent-
ly damaging the hose.
Prior to using a Timberline Firefighter Clamp, the user should consult and
observe any recommendations or precautions from hose manufacturers and
industry standards. Safety first. Timberline Firefighter Clamps must be
installed by qualified, trained personnel only and must never be left on the
hose unattended.
Timberline Firefighter Clamps are crafted from high strength aluminum for supe-
rior durability and will not bend or break under normal use. However, care must
be taken to ensure the hose is free of foreign materials, and the proper tool is be-
ing used on the appropriate hose. Avoid excessive force to prevent tool damage.

© 2008 Timberline Tool All Rights Reserved.
4
SAFETY INSTRUCTIONS
SAVE THESE FOR FUTURE REFERENCE
Fire Tool Safety
The FF1-S is designed to be used on single jacket canvas or syn-
thetic hose up to 1-3/4” in diameter.
Observe hose manufacturers’ and industry recommendations and precautions that
apply to shut off of pressurized hose.
Never leave the clamp on the hose unattended for an extended period of time.
Inspect the tool for signs of damage prior to use, and make sure the hose is not
damaged and will be able to withstand the pressure when the flow is stopped.
Make sure that the hose is clear of any rock, dirt, debris, etc.
Always hold the clamp away from your body, and keep the clamp
and hose on the ground at all times during the operation.
Do not exceed the pressure rating of the hose or 300 psi.
Use only on 3/4” to 1-3/4” diameter re hose sizes.
Remember SAFETY IS FIRST
Workplace Safety
Always follow applicable company and OSHA safety procedures.
Safety first. Timberline shut-off tools must be used by qualified, trained personnel
only and must never be left on the hose unattended.

TIMBERLINE FF1-S
5
Personal Safety
Stay Alert, watch what you are doing, and do not use tools while
tired or under the influence of narcotics, alcohol, or medication.
Use proper clothing, eye protection, and safety equipment when
using shut-off clamps.
Amoment of inattention while operating shut-off tools may result in personal injury.
Store idle tools out of reach of children and other untrained persons.
Specic Tool Safety
If you have used other Timberline products please be aware that the opera-
tion of this tool may differ from others and that you may need to follow different
rules. Always consult the manual to insure you are following the correct safety
instructions to avoid personal injury.
Tool Usage Safety
Do not force the tool to perform a shut-off.
Maintain the tool with care. Aproperly maintained tool will be less
likely to cause damage and is easier to control.
Check for misalignment, binding of parts, breakage of parts, and other conditions
that might affect the operation of the tool. Accidents may be caused by improp-
erly maintained tools.
Failure to use the FF1 in the manner specified in this manual may result in injury
and/or permanent damage to the tool.
Tool Service Safety
Tool service must only be performed by qualified repair personnel. Service or
maintenance performed by unqualified personnel could result in a risk of injury.

© 2008 Timberline Tool All Rights Reserved.
OPERATING PROCEDURE
1. Set the fire hose nozzle in a “weeping” position.
2. Kneel beside the fire hose and hold the clamp in the
open position with one hand making sure the top
handle points upward. Fig 1
3. With the other hand, place the hose as far as pos-
sible into the open jaws and place the tool on the
ground. Fig 2
4. Stabilize the clamp by placing your foot on the
footpad.
5. Hold the hose with one hand on each side of the
clamp and roll the hose fully into the jaws until it
comes in contact with the links. Fig 3
6. Depress the top handle on the clamp to instantly
shut off water supply. Fig 4
The clamp is self-locking and will remain
locked until released.
6
Fig 4
Fig 1
Fig 2
Fig 3

TIMBERLINE FF1-S
7
7. To begin removal of the tool from the hose,
place your foot on the footpad and firmly grip
the top handle with both hands. Fig 5
8. To complete the removal of the tool, pull the
handle up until the clamp passes “over center”
and the jaws unlock. Fig 6
As soon as the clamp unlocks,
the pressure in the hose will
cause the handles to spread
rapidly. Be prepared to ap-
ply downward pressure on the
handles so they open slowly and
the hose is re-pressurized in a
controlled manner.
An uncontrolled pressure surge
may cause the end of the hose to
jump dangerously and unpredict-
ably. It is important to release the
clamp from the hose in a slow,
controlled manner to avoid injury
or damage.
Fig 5
Fig 6

© 2008 Timberline Tool All Rights Reserved.
8
SERVICE
Aer every 10 uses:
1. Lubricate the pins and bushings with light oil.
If you have questions, please feel free to contact our customer
service representatives at 1-800-735-6845 or by email at
[email protected].
ACCESSORIES
Any accessories or attachments recommended for use with your
Timberline Tool are specified in this manual. The use of any other
accessories or attachments might present the risk of injury. Only
use accessories or attachments for their stated purpose.

TIMBERLINE FF1-S
9
TIMBERLINE LIMITED WARRANTY
Warranty Policy
Every product manufactured by Timberline Tool is thoroughly inspected and tested before
leaving the factory. Our products are warranted to be free of defects from workmanship
and materials for the period of ONE YEAR from the date of original purchase. Should any
trouble develop on our tools, handles, or accessories during this one-year period please
call 800.735.6845 to obtain return authorization for repair. If inspection shows the trouble
is caused by defective workmanship or material, Timberline Tool will repair or, at our option,
replace the product without charge.
This Warranty does not apply where:
• Repairs have been made or attempted by others.
• Repairs are required because of normal wear and tear.
• The tool has been abused, misused, or improperly maintained.
• Alterations have been made to the tool.
IN NO EVENT SHALLTIMBERLINE TOOL BE LIABLE FOR ANY INDIRECT, INCIDENTAL
OR CONSEQUENTIAL DAMAGES FROM THE SALE OR USE OF THE PRODUCT. THIS
DISCLAIMER APPLIES BOTH DURING AND AFTER THE TERM OF THIS WARRANTY.
TIMBERLINE TOOL DISCLAIMS LIABILITY FOR ANY IMPLIED WARRANTIES, INCLUD-
ING IMPLIED WARRANTIES OF “MERCHANTABILITY” AND “FITNESS FOR ASPECIFIC
PURPOSE,” AFTER THE ONE-YEAR TERM OF THIS WARRANTY.
This Warranty gives you specific legal rights, and you may also have other rights which
vary from state to state. Some states do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitation or exclusion may not apply to you. Some
states do not allow limitation on how long an implied warranty lasts, so the above limitation
may not apply to you.

© 2008 Timberline Tool All Rights Reserved.
10
is Page Intentionally Le Blank

TIMBERLINE FF1-S
11
is Page Intentionally Le Blank

[phone]
[phone]
www.timberlinetool.com
90 Conesto
g
a Ct. Kalis
p
ell
,
MT 59901 USA