TIME MARK DRA-1 User manual

MODEL DRA-1
Material 20 gauge CRS
Color Gray
Dimensions 6” x 4” x 0.85”
Weight 0.75 lbs.
Mounting four #8 -32 mounting holes
Hardware (supplied) four #8 -32 x 3/8” screws
SPECIFICATIONS
DESCRIPTION
The DRA-1 DIN Rail Adapter is designed for quick
attachment and detachment of various surface-mount
devices onto a standard 35mm DIN rail.
Four #8-32 mounting holes located on the face of the
Adapter support numerous models. The Adapter and
grip plate are made of 20 gauge steel and assembled
as one unit for durability. Constructed with two high
tension extension springs the DRA-1 Adapter will
securely fasten surface-mount enclosures to a standard
35mm DIN rail.
The mounting hole pattern matches a standard Time
Mark surface-mount enclosure.
DIMENSIONS
6.00"
3.90"
0.85"
3.00"
5.50"
0.25"
# 8 - 32 UNC
(4) TYP.
ll Surface to DIN Rail Mount
ll Spring-loaded for Quick Attachment
MODEL DRA-1
DIN Rail Adapter
USE WITH TIME MARK MODELS:
3-PHASE MONITORS CURRENT MONITORS
200 272
263 2732
2638 2734
2644 274
265 POWER SUPPLIES
269 6524
ALTERNATING RELAYS SPECIAL CONTROLS
271 421
471 VOLTAGE MONITORS
PUMP/LIQUID LEVEL 292
422 2962
TIME MARK is a division of
Telephone: Main -[phone]
Sales -[phone]
Fax: [phone]
E-mail: [e-mail]
Internet:http://www.time-mark.com
Doc No. 87A413 12/00
© 2000 TIME MARK CORPORATION
11440 East Pine Street
Tulsa, Oklahoma 74116

Once the unit is attached to the Adapter, place them
both in position next to the 35mm DIN rail. Pull down
on the movable part of the grip plate, and position the
Adapter (with mounted unit) onto the DIN rail.
When the unit is in the desired position, simply release
the spring loaded grip plate. The top jaw of the grip
plate should be holding the top part of the DIN rail. The
movable bottom part of the grip plate should be holding
the bottom lip of the DIN rail.
TROUBLESHOOTING
If the DRA-1does not seat properly or fit onto a
standard 35mm DIN rail, check to see that the DIN rail
is not bent or deformed in some way. Also check for
obstructions where there are moving parts.
WARRANTY
The Model DRA-1 DIN Rail Adapter is warranted to be
free from defects in materials and workmanship for one
year. Should this device fail to operate, we will repair
or replace it for one year from the date of purchase.
For complete warranty details, see the Terms and
Conditions of Sales page in the front section of the
Time Mark catalog.
DIN RAIL
GRIP PLATE
UNIT
ADAPTER
INSTALLATION
Make sure that the mounting holes, on the unit you
will be attaching, will match up correctly to the holes
on the adapter plate.
Using the four # 8-32 screws supplied, mount the unit
to the DRA-1 adapter plate.
Note: for a better grip of the unit to the adapter plate,
Locktite (Blue Dot) is recommended.
DIN RAIL
GRIP PLATE
UNIT
ADAPTER
GRIP PLATE
DIN RAIL UNIT
ADAPTER
MODEL DRA-1DIN Rail Adapter
READ ALL INSTRUCTIONS BEFORE INSTALLING, OPERATING OR SERVICING THIS DEVICE.
KEEP THIS DATA SHEET FOR FUTURE REFERENCE.
GENERAL SAFETY
MOUNTED INSTRUMENT WEIGHT SHOULD NOT EXCEED 20 POUNDS.
DIN RAIL END BRACKETS ARE REQUIRED WHEN MOUNTING THE RAIL IN A VERTICAL POSITION.
THIS DEVICE SHOULD BE INSTALLED AND SERVICED BY QUALIFIED PERSONNEL.
PROPER ATTENTION SHOULD BE GIVEN TO ANY MOVING PARTS.
Installation Instructions
TIME MARK is a division of
Telephone: Main -[phone]
Sales -[phone]
Fax: [phone]
E-mail: [e-mail]
Internet:http://www.time-mark.com
Doc No. 87A413 12/00
© 2000 TIME MARK CORPORATION
11440 East Pine Street
Tulsa, Oklahoma 74116