tispro SX1000 User manual

SX1000 Hot Towel Cabinet
AMERICA’S BEST
VALUE BRAND!
Item #390412• New Hudson, MI 48165
www.tngworldwide.com • 800.520.6000
Made in China • ©2016 TNG
AMERICA’S BEST
VALUE BRAND!
Safety Precautions
Caution and proper procedures must be practiced at all times when using electrical
appliances. When using electrical appliances, basic safety precautions should always be
followed, including the following:
• Do not use appliance for other than intended use.
• Do not touch hot surfaces. Use handle or knobs.
• To protect against electrical shock, do not immerse cord, plugs or appliance in water
or other liquid.
• Unplug from outlet when not in use and before cleaning. Cooling the machine before
putting on or taking off parts.
• Do not operate any appliance with a damaged cord or plug or after the appliance
malfunctions or has been damaged in any manner. No user serviceable parts inside.
• The use of accessories and/or attachments not recommended or sold by the appliance
manufacturer may cause injuries.
• Do not use outdoors. This appliance is intended for indoor use only.
• Do not let cord hang over edge of table or counter, or touch hot surfaces.
• Close supervision is necessary when any appliance is used by or near children.
• Do not leave the appliance unattended when switched on.
• Extreme caution must be used when moving an appliance containing hot liquids.
• The appliance is not intended to be operated by means of an external timer or
separate remote-control system.
• The temperature of accessible surfaces may be high when the appliance is operating.
• If using an extension cord, the marked electrical rating of the extension cord should be
at least as great as the electrical rating of the appliance.
Internal surfaces, wire baskets, towels and steam may be hot. Use with extreme
caution when removing hot towels or baskets. Always use protective heat-resistant
gloves or mitts to avoid steam or other burns. Ignoring the warnings may result in
harm or serious injury.
SX1000
Hot Towel Cabinet
Troubleshooting
1. There is excessive moisture when the towel warmer is ON or the towels are heating
up very slowly.
• Check to see that the towels are only slightly damp. Excess moisture and/or slow
heating time may be a result of soaked towels.
2. The door is not closing properly and/or steam is escaping
• Check that the silicone door seal is in place. Push into door groove to assure
proper fit.

SX1000 Hot Towel Cabinet Operation Manual
Congratulations on your purchase of the TISPRO SX1000 Hot Towel Cabinet.
Please read the instructions and safety tips before use. Your Hot Towel Cabinet comes
with a one-year limited warranty. If for any reason you need service, please call 800-520-6000.
Product Specification
Towel Warmer
Voltage: Single phase, 110V/60Hz
Power: 200W
Temperature: 158°F – 176°F
Safety device: Thermal fuse
Insulation: Glass wool
Inside size: 14 1/2”W x 7 1/2”D x 9 1/2”H
Outer size: 17 3/4”W x 10 1/2”D x 14”H
UV Bulb
Bulb type: E17 (17mm diameter)
Power: 3W
Radiation type: UV-C, wave length 240nm
Names of all parts
Before Operation
• Be sure to remove all packing material before use.
• Place the unit on a well ventilated, flat, sturdy surface away from heat sources. The unit
should not be used in the immediate vicinity of water (such as bathtub, washbowls,
etc.) where the likelihood of immersion may occur.
• Plug cord into a 110V power outlet.
• Remove the wire basket and set aside.
Operation
1. Run towels briefly under water.
2. Wring out excess water from the towels. Towels should be damp, not soaked. You
may need to wring out several times.
3. Fold or roll towel and place towels into the wire basket. Do not overload the wire
basket or directly place towels into the towel warmer.
4. Insert the basket with towels into towel warmer.
5. Close the door firmly.
6. Turn on the HEAT switch and indicator light will go on. In about 10 minutes, the
temperature inside the cabinet will heat up to approximately 200°F and the indicator
light will go off. When the temperature drops in cabinet the light will go back on. The
unit will automatically heat up again, and continue to cycle like this.
7. Turn on the UV switch. The UV indication lamp will remain illuminated.
Maintenance
1. Turn OFF the unit.
2. Unplug the cord from the outlet.
3. Wait for contents to cool before handling. Contents may be hot. Remove the wire
basket and towels. Set the wire basket aside to dry.
4. With a soft cloth, wipe down the internal surfaces. Do not use harsh chemicals or
abrasives. To clean exterior, use a soft cloth and mild soap.
5. Pull the drip tray forward and empty contents. Set the drip tray aside to dry.
Replacing the UV Bulb
1. Turn OFF the unit.
2. Unplug the cord from the outlet.
3. Screw off the faulted UV bulb.
4. Screw on a new E17/3W UV bulb, recommended wave length 240nm (UVC).