Titan Fitness MFTS45UPv2-2MFTSSHLF User manual

MASS STORAGE SYSTEM RACKS
MFTS45UPv2-(2)MFTSSHLF, MFTS45UPv2-(2)MFTSSHLF70,
MFTS74UPv2-(3)MFTSSHLF, MFTS74UPv2-(3)MFTSSHLF70
401430, 401431, 401432, 401433
Operator’s Manual
Read the Operator’s Manual entirely. When you see this
symbol, the subsequent instructions and warnings are
serious follow without exception. Your life and the lives
of others depend on it!

2
2-TIER PARTS DIAGRAM / EXPLODED VIEW
SHOWN WITH THE 42-INCH TUBE SHELVES

3
2-TIER PARTS LIST
KEY DESCRIPTION QTY
(1) HEX BOLT M12X80 16
(2) SQUARE TUBE END CAP 4
(3) UPRIGHT POST 4
(4) FLAT WASHER M12 16
(5) SPRING WASHER M12 16
(6) HEX NUT M12 16
(7) ROUND TUBE END CAP 8
(8) 42” TUBE SHELF OR 70” TUBE SHELF 2
(9) SIDE BRACE 2

4
2-TIER ASSEMBLY INSTRUCTIONS
SPECIAL NOTES:
−Build on flat and level ground
−Avoid tightening bolts down completely until the rack is fully assembled
1. Insert Square Tube End Cap (2) into top of Upright Post (3).
2. Insert Round Tube End Cap (7) into top of 42” or 70” Tube Shelf (8).
3. Attach Side Brace (9) to the middle of two Upright Post (3), using Hex Bolt M12x80
(1), Flat Washer M12(4), Spring Washer M12 (5) and Hex Nut M12 (6). The order of
assembly is to insert Hex Bolt M12x80 (1), through these parts, and then place Flat
Washer M12(4), Spring Washer M12 (5) and Hex Nut M12 (6) onto the end of the
bolt. Fasten the hardware on, but do not tighten.
4. Attach 42” or 70” Tube Shelf (8) to the above Upright Post (3) assembly, using Hex
Bolt M12x80 (1), Flat Washer M12(4), Spring Washer M12 (5) and Hex Nut M12 (6).
The order of assembly is to insert Hex Bolt M12x80 (1), through these parts, and then
place Flat Washer M12(4), Spring Washer M12 (5) and Hex Nut M12 (6) onto the end
of the bolt. Fasten the hardware on, but do not tighten.
5. Tighten all hardware.

5
3-TIER PARTS DIAGRAM / EXPLODED VIEW

6
3-TIER PARTS LIST
KEY DESCRIPTION QTY
(1) HEX BOLT M12X80 16
(2) SQUARE TUBE END CAP 4
(3) UPRIGHT POST 4
(4) FLAT WASHER M12 16
(5) SPRING WASHER M12 16
(6) HEX NUT M12 16
(7) ROUND TUBE END CAP 8
(8) 42” TUBE SHELF OR 70” TUBE SHELF 3
(9) SIDE BRACE 2

7
3-TIER ASSEMBLY INSTRUCTIONS
SPECIAL NOTES:
−Build on flat and level ground
−Avoid tightening bolts down completely until the rack is fully assembled
1. Insert Square Tube End Cap (2) into top of Upright Post (3).
2. Insert Round Tube End Cap (7) into top of 42” or 70” Tube Shelf (8).
3. Attach Side Brace (9) to the middle of two Upright Post (3), using Hex Bolt
M12x80 (1), Flat Washer M12(4), Spring Washer M12 (5) and Hex Nut M12
(6). The order of assembly is to insert Hex Bolt M12x80 (1), through these
parts, and then place Flat Washer M12(4), Spring Washer M12 (5) and Hex
Nut M12 (6) onto the end of the bolt. Fasten the hardware on, but do not
tighten.
4. Attach 42” or 70” Tube Shelf (8) to the above Upright Post (3) assembly, using
Hex Bolt M12x80 (1), Flat Washer M12(4), Spring Washer M12 (5) and Hex
Nut M12 (6). The order of assembly is to insert Hex Bolt M12x80 (1), through
these parts, and then place Flat Washer M12(4), Spring Washer M12 (5) and
Hex Nut M12 (6) onto the end of the bolt. Fasten the hardware on, but do not
tighten.
5. Tighten all hardware.

8
ACKNOWLEDGEMENT OF RISK AND RELEASE OF LIABILITY
The use of any equipment, including this one, involves the potential risk of injury. Apart from any warranty
claim that might be presented for a claimed defect in material or workmanship of the product, you accept
and assume full responsibility for any and all injuries, damages (both economic and non-economic), and
losses of any type, which may occur, and you fully and forever release and discharge Titan, its insurers,
employees, officers, directors, associates, and agents from any and all claims, demands, damages,
rights of action, or causes of action, present or future, whether the same be known or unknown,
anticipated, or unanticipated, resulting from or arising out of the use of said equipment.
This equipment must be used with care by capable and competent individuals under supervision,
WARNING
Heavy object. Use lifting aids and
proper lifting techniques when moving.
Choking hazard. Small parts –
Please exercise caution if small
children or pets are present.
Sharp objects may be involved.
Use precaution and protection.
TITAN LIMITED WARRANTY: TERMS, EXCLUSIONS AND LIMITATIONS OF REMEDIES
This product comes with a one (1) year limited warranty that can be found at
www.titan.fitness/warranty.html Please review the same for all details regarding the
Titan Limited Warranty.
THE TITAN LIMITED WARRANTY FOUND AT WWW.TITAN.FITNESS/WARRANTY IS EXCLUSIVE AND IS IN
LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY IMPLIED WARRANTY OF
MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR PURPOSE, EACH OF WHICH IS HEREBY
DISCLAIMED.

9
NEED HELP? CONTACT US FIRST.
1-888-410-1503
info@titan.fitness
www.titan.fitness
© 2021 Titan Brands