TK CM7 User manual

1
Operator’s Safety and Service Manual
Concrete Mixer
CM7
CM9
CM12
TABL OF CONT NTS
It is the OWNER´S RESPONSABILITY to communicate information on the
SAFE USE an OPERATION of this machine to the operators.
09052014
www.discount-equipment.com
Discount-Equipment.com

Discount-Equipment.com is your online resource for commercial and industrial
quality parts and equipment sales.
Locations:
Florida (West Palm Beach): 561-964-4949
Outside Florida TOLL FREE: 877-690-3101
Need parts? Check out our website at www.discount-equipment.com
Can’t find what you need?
Click on this link: http://www.discount-equipment.com/category/5443-parts/ and fill out
the request form.
Please have the machine model and serial number available in order to help us get
you the correct parts. One of our experienced staff members will get back to you with
a quote for the right part that your machine needs.
We sell worldwide for the brands: Genie, Terex, JLG, MultiQuip, Mayco, Toro/Stone,
Diamond Products, Magnum, Airman, Mustang, Power Blanket, Nifty Lift, Atlas Copco,
Chicago Pneumatic, Allmand Brothers, Essick, Miller Spreader, Skyjack, Lull, Skytrak,
Tsurumi, Husquvarna/Target, Whiteman-Concrete/Mortar, Stow-Concrete/Mortar, Baldor,
Wacker, Sakai, Snorkel, Upright, Mi-T-M, Sullair, Neal, Basic, Dynapac, MBW, Weber,
Bartell, Bennar Newman, Haulotte, Ditch Runner, Blaw-Knox, Himoinsa, Best, Buddy,
Crown, Edco, Wyco, Bomag, Laymor, Terremite, Barreto, EZ Trench, Takeuchi, Basic, Bil-
Jax, Curtis, Gehl, Heli, Honda, ICS/PowerGrit, Puckett, Waldon, ASV, IHI, Partner, Imer,
Clipper, MMD, Koshin, Rice, Gorman Rupp, CH&E, Cat Pumps, Comet, General Pump,
Giant,AMida, Coleman, NAC, Gradall, Square Shooter, Kent, Stanley, Tamco, Toku, Hatz,
Kohler, Robin, Wisconsin, Northrock, Oztec, Toker TK, Rol-Air, Small Line, Wanco, Yanmar

2
TABL OF CONT NTS
1.Serial Number Location .............................................. 3
2.Parts Or ering Proce ure .......................................... 3
3.Operating Instructions ............................................... 4
4.Safety Precaution ....................................................... 6
5.Safety Notice & Decals ............................................... 7
6.Safety Decal Location ................................................. 9
7.Before Operating...................................................... 11
8.Operation Instruction............................................... 11
9.Starting Engine ......................................................... 12
10.Service Instructions ................................................ 13
11.Maintenance Sche ule .......................................... 13
12.Replacements ......................................................... 14
13.Torque Chart .......................................................... 15
14.Warranty ................................................................ 16
15.Warehouse Locations ............................................. 17
16.Notes ...................................................................... 18
17.Parts List Break own .................................... Attache
Discount-Equipment.com

3
1. S RIAL NUMB R LOCATION
The mo el/serial number ecal is locate on the shrou assembly (black).
(Write model number)
(Write serial number)
The unit’s year of manufacture can be etermine by the serial number. Contact your nearest
sales branch or for more information.
This Unit warranty is state in this Operational an Safety manual on page 16. Failure to
return warranty registration car ren ers the warranty null an voi .
An engine owner’s manual is also attache to every unit. Engine parts may or er from any
authorize ealer. Refer to the engine owner´s manual lo learn about specifications an part
i entification.
2. PARTS ORD RING PROC DUR :
Parts are available worl wi e an must be or ere through your local istributor. If you
can’t locate the istributor in your area refer to page 17 of this manual to locate the
nearest branch an contact numbers for assistance.
ALWAYS HAV R ADY:
1. Mo el an serial number of machine when or ering parts.
2. Mo el an serial number of engine when or ering engine parts.
3. Item part number(S), escription, an quantity.
4. Company name, a ress, zip co e, an purchase or er number.
5. Preferre metho of shipping.
R M MB R – you own the best. If repairs are needed use
only purchased parts from authorized distributors.
Discount-Equipment.com

4
3. OP RATING INSTRUCTIONS
INTRODUCCION
Mixers are inten e for use in several applications. They are powere by four cycle gas
engines or electric motors an are available in ifferent sizes an manufacturers.
This Operation manual contains only stan ar parts. Variations of these parts as well as other
special parts are not inclu e . Contact your local istributor for assistance in i entifying
parts not inclu e in this manual.
ASS MBLY INSTRUCTIONS
1. Remove the mixer an all components from its shipping crate. You will see:
•Two wheels.
•Axle assembly with hubs on each si e, mounting loops an 8 lug nuts.
•Selecte hitch with lock pin an bolt an safety bolt with hair pin.
Note: All installation hardware must be inserted into its respective location on the
mixer, see parts explosion for more details.
2. After removing all mixers’ safety packing, while stan ing on an en , locate the axle’s
place on the mixer. You nee to locate the bolts attache to the mixer shrou , bolte
to the pallet an make sure this bolts are remove .
3. Lift the axle up to the mixer frame an position it in the center of the mixer make sure
the axle gui e are insi e the mounting loops (both si es) before you hook the axle on
the mixers springs or mixer frame ( epen ing mixer size) an bolt the mounting loops.
4. Insert two 1/2 inch bolts with a washer through the mounting loops to secure the axle.
Faster each mounting loop si e an tight the bolts at 57 ft.-lbs.
5. Remove the lug nuts from the axle an mount the spee wheel, after wheel is
mounte procee to place the lug nuts (make sure the conical (tapere ) en is facing
the insi e of the wheel. Torque to 105 ft.-lbs.
6. Procee with the secon wheel using the steps of point #3.
7. Using appropriate Equipment, put the mixer own to the groun .
Warning: failure to use proper lifting equipment could cause
mixer to fall and cause serious injury.
8. Position the safety chain through the key slots in the front leg. A just the chain’s en s
to equal length.
9. Remove the safety bolt an pin from the tow bar.
Discount-Equipment.com

5
10. Install the tow bar through the front leg.
11. Insert the pin through the front leg an the front hole in the tow bar. Secure the pin
with a hairpin cotter.
Insert the 3/4" bolt through the rear hole an secure with a lock washer an nut.
Tighten securely.
Discount-Equipment.com

6
4. SAF TY PR CAUTIONS
R AD AND STUDY TH FOLLOWING SAF TY INFORMATION B FOR ATT MPTING TO OP RAT THIS
QUIPM NT. IN ADDITION, NSUR THAT V RY INDIVIDUAL WHO OP RAT S OR WORKS WITH
THIS QUIPM NT IS FAMILIAR WITH TH S SAF TY PR CAUTIONS.
WARNING - L THAL XHAUST GAS!
An internal combustion engine ischarges carbon monoxi e, which is a poisonous an o orless
invisible gas. Death or serious illness may result if inhale . Operate only in an area with goo
ventilation, N V R IN A CONFIN D AR A!
WARNING - DANG ROUS FU LS!
Use extreme caution when storing, han ling an using fuels - they are highly volatile an explosive in
the vapor state. Do not a fuel while engine is running. Stop an cool the engine before a ing fuel.
DO NOT SMOK WH N R FU LING!
SAF TY GUARDS
It is the owner's responsibility to ensure ALL GUARDS AND SHI LDS are in place an in working or er.
IGNITION SYST MS
Breakerless magneto an batteries ignition systems CAN CAUS S V R L CTRICAL SHOCKS, avoi
contact with these components or their wiring.
SAF DR SS
DO NOT W AR loose clothing, rings, wristwatches, etc., near machinery.
NOIS PROT CTION
Wear O.S.H.A. specifie hearing protection evices.
FOOT PROT CTION
Wear O.S.H.A. specifie steel tip safety shoes.
H AD PROT CTION
Wear O.S.H.A. specifie safety helmets.
Y PROT CTION
Wear O.S.H.A. specifie eyes shiel s, safety glasses, an sweat ban s.
DUST PROT CTION
Wear O.S.H.A. specifie ust mask or respirator.
OP RATOR
Keep chil ren an bystan ers off an away from the equipment.
OP RATOR
For etails on safety rules an regulations in the Unite States, contact your local Occupational Safety
an Health A ministration (O.S.H.A.) office. Equipment operate in other countries must be operate
an service in accor ance an compliance with any an all safety requirements of such country. The
publication of these safety precautions is one for your information oes not by the publication of
these precautions, imply or in any way represent that these are the sum of all angers present near
equipment. If you are operating a unit it is your responsibility to insure that such operation is
in full accor ance with all applicable safety requirements an co es. All requirements of the Unite
States Fe eral Occupational Safety an Health A ministration Act must be met when operate in
areas that are un er the juris iction of that Unite States Department.
Discount-Equipment.com

5.
SAF TY NOTIC & D CALS
IMPORTANT NOTIC
The "SAF TY AL RT SYMBOL"
is use to call attention
to those operating or working with this equipment. These symbols can be foun throughout the
manual an on the unit itself. Please rea these warnings an cautions carefully.
R AD SAF TY D CALS CAR FULLY
Carefu
lly rea an follow all safety ecals. Keep them in goo con ition
age
, replace as require . If repainting,
authorize
Distributors. Decals are not shown to scale.
201012
201155
7
SAF TY NOTIC & D CALS
IMPORTANT NOTIC
is use to call attention
to items or operations that may be angerous
to those operating or working with this equipment. These symbols can be foun throughout the
manual an on the unit itself. Please rea these warnings an cautions carefully.
R AD SAF TY D CALS CAR FULLY
lly rea an follow all safety ecals. Keep them in goo con ition
, replace as require . If repainting,
R PLAC ALL
ecals. Decals are available from your
Distributors. Decals are not shown to scale.
201157
to items or operations that may be angerous
to those operating or working with this equipment. These symbols can be foun throughout the
manual an on the unit itself. Please rea these warnings an cautions carefully.
R AD SAF TY D CALS CAR FULLY
lly rea an follow all safety ecals. Keep them in goo con ition
s. If they become
ecals. Decals are available from your
201151
201150
Discount-Equipment.com

8
5. SAF TY NOTIC & D CALS
S IMPORTANT NOTIC
The "SAF TY AL RT SYMBOL" is use to call attention to items or operations that may be angerous
to those operating or working with this equipment. These symbols can be foun throughout the
manual an on the unit itself. Please rea these warnings an cautions carefully.
R AD SAF TY D CALS CAR FULLY
Carefully rea an follow all safety ecals. Keep them in goo con ition. If they become
amage , replace as require . If repainting, R PLAC ALL ecals. Decals are available from
your authorize Distributors. Decals are not shown to scale.
201003 (x2)
201005
201026
201152
201005
201006
201001 BIG
201001 SMALL
290791
201004
201154
Discount-Equipment.com

6.
SAF TY D CAL LOCATION
9
SAF TY D CAL LOCATION
Discount-Equipment.com

10
6. SAF TY D CAL LOCATION
When is electric
Discount-Equipment.com

11
7. B FOR OP RATING
R M MB R! It is the owner´s responsibility to communicate information on the safe
use an proper operation of this unit to the operators.
Before operating, review SAFETY PRECAUTIONS liste on page 5 of this manual.
Familiarize yourself with the operation of the unit an confirm that all controls
function properly BEFORE starting engine.
Locate the killing switch an assure you know how to STOP the unit.
Make sure han s, feet, an clothing are at a safe istance from any moveable parts
prior to starting.
Shrou s an gri s are provi e to protect the operator or structures in close proximity
to rotating hot engine parts. It is the R SPONSABILITY OF TH OP RATOR to see that
they are properly in place.
OIL LEVEL - Check the oil level in the engine. For more information see "Lubrication"
un er the engine "Owner's Manual" the "Maintenance" section of this manual. All
mixers come without oil running an engine without lubrication may amage the
engine.
AIR CLEANER - Check to ensure elements are in goo con ition an properly installe .
Review every ecal with the OPERATOR.
FUEL SUPPLY - Engines on Mixer equipment require an automotive gra e of clean,
fresh, unlea e or regular gasoline. All mixers come without gasoline and oil.
FUEL FILTER - Check to ensure element is in goo con ition... Replace if it is clogge or
amage .
LUBRICATION POINTS - Make sure all pillow blocks have been properly grease .
8. OP RATION INSTRUCTIONS
Gas engine
1. Open the fuel valve.
2. Pull the stop switch on the engine shrou to its "Out" position.
3. Move the engine throttle control to the "FAST" position.
4. Choke the engine if necessary.(You may not nee to choke a warm engine)
5. Pull the starter string.
6. After the engine starts, move the choke lever to the open position, move the throttle
level to the "IDLE" position an let the engine warm-up for one or two minutes.
lectric motor
1. Plug the motor into a suitable power source.
2. Move the switch on the motor to the "on" position.
Discount-Equipment.com

OP RATING
1.
If using a gas engine, allow the engine t
position.
2. Close the engine shrou
DO NOT OP RAT TH MIX R WITH TH SHROUD OP N!
3. After loa ing a batch of
concrete
4. After ischarg
ing the final batch of
running.
Discharge the water after the insi e of the mixer is clean.
9. STARTING NGIN
GAS NGIN
1.
Move the engagement lev
2.
Whenever possible it is recommen e to let the
3.
Push in the engine stop s
4.
Close the fuel valve.
L CTRIC MOTOR
1.
Move the switch on the motor to the "off" position.
STOP TH NGIN OR L CTRIC MO
A ing fuel.
Leaving equipment unatten e for any a
of time.
Making any repairs or a justments
Transportation.
TOWING:
1. Stop th
e engine or electric motor.
2. Close an hook
the engine shoul .
3.
Rotate the rum into the tow
4.
Secure the mixer hitch an safety chains to the vehicle.
B FOR TOWING:
Make sure the axle an tow bar har ware is tight
Check the con ition of the pin on the tow bar an make sure it is secure
Remove
any loose ebris from the mixer
Use safety chains when towing.
12
If using a gas engine, allow the engine t
o warm up then move the throttle to the fast
DO NOT OP RAT TH MIX R WITH TH SHROUD OP N!
concrete
, it is recommen e to a
water for the next batch.
ing the final batch of
concrete
, a water to the rum while the mixer is
Discharge the water after the insi e of the mixer is clean.
9. STARTING NGIN
Move the engagement lev
er to the "IDLER" position.
Whenever possible it is recommen e to let the
engine i le before stopping.
Push in the engine stop s
witch on the engine shrou .
Close the fuel valve.
Move the switch on the motor to the "off" position.
STOP TH NGIN OR L CTRIC MO
TOR B FOR :
Leaving equipment unatten e for any a
mount
Making any repairs or a justments
to the unit.
e engine or electric motor.
the engine shoul .
Rotate the rum into the tow
position an secure it with
the locking pin.
Secure the mixer hitch an safety chains to the vehicle.
Make sure the axle an tow bar har ware is tight
ene .
Check the con ition of the pin on the tow bar an make sure it is secure
any loose ebris from the mixer
.
Use safety chains when towing.
MAXIMUM TOW SP D: 45 mph
o warm up then move the throttle to the fast
DO NOT OP RAT TH MIX R WITH TH SHROUD OP N!
water for the next batch.
, a water to the rum while the mixer is
Discharge the water after the insi e of the mixer is clean.
engine i le before stopping.
the locking pin.
Check the con ition of the pin on the tow bar an make sure it is secure
.
MAXIMUM TOW SP D: 45 mph
Discount-Equipment.com

13
10. S RVIC INSTRUCTIONS
Never service or lubricate the unit engine while running.
After servicing the unit, restore and fasten all guards, shields, and covers to their
original positions.
Never drain oil into the ground, into open streams, or down sewage drains.
NGIN
See engine owner´s manual maintenance schedule.
DRUM
1. Wash the rum after every ay’s usage.
2. Pull the locking pin an tip the rum forwar to rain water excess.
3. Return rum to towing position an secure with locking pin before moving mixer.
LUBRICATION
1. Grease all fittings aily. All mixers have 6 grease fittings, 4 pillow blocks an 2 rum
trunnions. Two of the fittings are locate at each en of the mixer rum on the top of
pillow blocks an trunnions.
The two remaining grease fittings are locate un er the engine shrou on the top of
the interme iate shaft pillow blocks (see picture below).
2. Electric mixers only: oil the rive chain once a week.
11. MAINT NANC SCH DUL
Maintenance Each
use
Every
20 hours
Every
50 hours
Every
100 hours
Yearly
Engine Refer to engine operator/owner
manual X X
Bearings Grease X X
V-Belts Check for excessive wear X X
Roller chain Check for excessive wear X X
Har ware Check an tighten 1,2 X X X
Tires Check air pressure X
1. Check all har ware after the first 5 hours of use, the follow the maintenance sche ule.
2. Re-torque the front leg an axle har ware after the first 50 miles travele , an then
follow the maintenance sche ule.
Discount-Equipment.com

14
12. R PLAC M NT
Parts Tolerance or Replacement Cycle
Engine Components Refer to your engine manufacturer´s Owner´s
Manual
V-Belts Replace if stretche to the point that the i ler oes
not work properly. Replace the V-belts if they are
cracke or torn.
Roller Chain
Replace if there is excessive play between the links
or the links are amage .
Gears Replace if the teeth are cracke or have become
sharp.
Hardware Re-torque all bolts after the first eight hours of
operation an check har ware every 25 hours.
Replace any worn or amage har ware as
nee e . Replacement har ware shoul be gra e 5
an zinc plate .
Safety Decals Replace if they become age , amage or cannot
be easily rea .
Discount-Equipment.com

15
13. TORQU CHART
Discount-Equipment.com

Discount-Equipment.com is your online resource for commercial and industrial
quality parts and equipment sales.
Locations:
Florida (West Palm Beach): 561-964-4949
Outside Florida TOLL FREE: 877-690-3101
Need parts? Check out our website at www.discount-equipment.com
Can’t find what you need?
Click on this link: http://www.discount-equipment.com/category/5443-parts/ and fill out
the request form.
Please have the machine model and serial number available in order to help us get
you the correct parts. One of our experienced staff members will get back to you with
a quote for the right part that your machine needs.
We sell worldwide for the brands: Genie, Terex, JLG, MultiQuip, Mayco, Toro/Stone,
Diamond Products, Magnum, Airman, Mustang, Power Blanket, Nifty Lift, Atlas Copco,
Chicago Pneumatic, Allmand Brothers, Essick, Miller Spreader, Skyjack, Lull, Skytrak,
Tsurumi, Husquvarna/Target, Whiteman-Concrete/Mortar, Stow-Concrete/Mortar, Baldor,
Wacker, Sakai, Snorkel, Upright, Mi-T-M, Sullair, Neal, Basic, Dynapac, MBW, Weber,
Bartell, Bennar Newman, Haulotte, Ditch Runner, Blaw-Knox, Himoinsa, Best, Buddy,
Crown, Edco, Wyco, Bomag, Laymor, Terremite, Barreto, EZ Trench, Takeuchi, Basic, Bil-
Jax, Curtis, Gehl, Heli, Honda, ICS/PowerGrit, Puckett, Waldon, ASV, IHI, Partner, Imer,
Clipper, MMD, Koshin, Rice, Gorman Rupp, CH&E, Cat Pumps, Comet, General Pump,
Giant,AMida, Coleman, NAC, Gradall, Square Shooter, Kent, Stanley, Tamco, Toku, Hatz,
Kohler, Robin, Wisconsin, Northrock, Oztec, Toker TK, Rol-Air, Small Line, Wanco, Yanmar
Discount-Equipment.com

19
Discount-Equipment.com

20
NO.
CODIGO CODE
DESCRIPCION DE PARTES DESCRIPTION OF PARTS CM7
CM9
CM12
1 0170CO01CH C-100 CHASIS CM7 YCM9 FRAME,CM7 CM9 1 1 -
0173CO01CH C-102 CHASIS CM12 FRAME CM12 - - 1
2 0100SC01FR C-103 FRENO BRAKE 1 1 1
3 0100FG01FR C-104 MANIVELA FRENO LOCKING PIN 1 1 1
4 0100SO01PD C-105 CHUMACERA PILLOW BLOCK 1 1 1
7 0000CO01LZ LANZA MILITAR (OPCIONAL) DRAW BAR, PINTLE HITCH 1 1 1
0000CO03LZ LANZA MILITAR BARRENO VERTICAL
(OPCIONAL) DRAW BAR, PINTLE HITCH VERTICAL HOLE 1 1 1
8 0100FG01YU C-107 PLATO DENTADO GEAR 1 1 1
9 0100FG01VO C-108 MASA VOLANTE 1 SACO HANDLE BLOCK 1 1 1 -
0103FG01VO C-109 MASA VOLANTE 2 SACOS HANDLE BLOCK 2 FOR CM12 - - 1
10 0100SC01VO C-110 VOLANTE 1 SACO HANDLE TUBE 1 1 -
0103SC01VO C-111 VOLANTE 2 SACOS HANDLE TUBE FOR CM12 - - 1
11 0100CO01YU C-112 YUGO RT YOKE RT 1 1 -
0103CO01YU C-113 YUGO LX YOKE FOR CM12 - - 1
12 0100LA03TQ C-114 GUARDA POLVOS 1 SACO PLATE 1 1 -
0103LA03TQ C-115 GUARDA POLVOS 2 SACOS PLATE FOR CM12 - - 1
13 OPCR038012 C-116 OPRESOR ALLEN 3/8 X 1/2 ALLEN SCREW 3/8 X 1/2 1 1 1
14 TCCN138MAQ C-117 TUERCA 1 3/8 NUT, 1-3/8 1 1 1
15 0100FG01TQ C-118 TAPON CACHUCHA DUST CAP 1 1 1
16 0171CO01TQ C-119 TANQUE CM7 DRUM CM7 1 - -
0172CO01TQ C-120 TANQUE CM9 DRUM CM9 - 1 -
0173CO01TQ C-121 TANQUE CM12 DRUM CM12 - - 1
17 0100FG02TQ C-122 CREMALLERA 115 DIENTES GEA RING 115TH 1 1 1
18 0100FG02YU C-123 PIÑON MOTRIZ 12 DIENTES PINNION 12TH 1 1 1
19 0100CR02YU C-124 FLECHA MOTRIZ SHAFT PINNION 1 1 1
20 POFG190516TK
C-125 POLEA MOTRIZ 19" PULLEY 19" 1 GROOVE 1 1 1
21 POLEA MOTRIZ (ver lista de poleas) PULLEY ENGINE (check list pulley) 1 1 1
22 0000BNB64 C-129 BANDA B64 BELT, B64 1 1 1
28 MOTOR ENGINE 1 1 1
30 0110CO01GA C-131 GABINETE ABATIBLE TK-ST HOOD, HINGED, ASSY 1 1 1
31 0100PL01RD C-133 BRACKETS BRACKETS (SPRINGS) 2 2 2
33 0130SC01RD C-134 EJE EXPORTACION TOKER AXLE 1 1 1
34 0200KI01RD C-135 ENSAMBLE MASA HUB HUB ASM, 4 BOLT 2 2 2
36 0000CO01RD C-136 LLANTA RIM 13" WHEEL RIM 13 2 2 2
0000CO02RD C-137 LLANTA RIM 12" WHEEL RIM 12 2 - -
39 TOCD038100 C-138 TORNILLO 3/8" X 1" ROSCA FINA GRADO
5 BOLT, HEXHD 3/8X1 NF G.5 1 1 1
40 RNPX038GAL C-139 RONDANA PLANA 3/8 GALVANIZADO PLAIN WASHER 3/8 21 21 21
41 0170LA01TR C-140 GUASA TRANSMISION 3/8 WASHER, TRANSMISSION 3/8 1 1 1
42 TOCD038112 C-141 TORNILLO 3/8 X 1 1/2 GALV. GRADO 5 BOLT, HEXHD 3/8X1-1/2 NF G.5 23 23 23
43 TCCS038GAL C-142 TUERCA 3/8 SEGURIDAD LOCK NUT, 3/8 19 19 19
46 RNRX038GAL C-144 RONDANA PRESION 3/8 GALVANIZADO SPRING WASHER 3/8 4 4 4
47 RNRX012GAL C-145 RONDANA PRESION 1/2 GALVANIZADO SPRING WASHER 1/2 7 11 11
48 TOCD012212 C-146 TORNILLO 1/2 X 2 1/2 GALV. GRADO 5 BOLT. HEXHD 1/2X2-1/2 G.5 5 5 5
Discount-Equipment.com

21
49 RNPX012GAL C-147 RONDANA PLANA 1/2 PLAIN WASHER 1/2 2 2 2
50 TOCD034312 C-148 TORNILLO 3/4 X 3 1/2 GALV. GRADO 5 BOLT HEXHD 3/4X3-1/2 G.5 1 1 1
51 TOCD012034 C-149 TORNILLO 1/2 X 3/4 GALV. GRADO 5 BOLT HEXHD 1/2X3/4 G.5 3 3 3
52 0000BA2788 C-150 BALERO 2788 (CONO Y TAZA) BALL BEARING, 2788 2 2 1
53 SM00516EXT C-151 SEGURO OMEGA 15/16 RETAINING RING, 15/16 2 2 1
54 0170CC01MO C-152 CUÑA 1/4 X 1 1/2 KEY, 1/4X1-1/2 2 2 2
57 0000BA6205 C-154 BALERO 6205 BALL BEARING, 6205 2 2 2
58 0000GRH200 C-155 GRASERA RECTA GREASE FITING,1/8 NPT 3 3 3
60 OPCQ038114 C-156 OPRESOR SET 3/8 X 1 1/4 CON TUERCA
3/8" SET SCREW, 3/8X1-1/4 W/NUT 3/8" 2 2 2
61 0170CO01GF C-157 GUARDA GEAR GUARD 1 1 1
62 TOCD038200 C-158 TORNILLO 3/8 X 2 GALV. GRADO 5 BOLT, HEXHD, 3/8X2 G.5 4 4 4
64 0000RF01GA C-159 REGATON 1/4 RUBBER SCREW 1/4 4 4 4
66 0000RF02GA C-161 GANCHO COFRE HOOK ASSEMBLY 2 2 2
68 0000CO02LZ LANZA TOKER COPLE BOLA 2" BALL HITCH (OPTIONAL) 1 1 1
0000CO04LZ LANZA TOKER COPLE BOLA VERTICAL 2"BALL HITCH VERTICAL HOLE 1 1 1
70 0000RF05RD C-164 CUBRE POLVO DUST COVER 2 2 2
71 0000RF01CH C-165 MUELLE REAL 2 HOJAS AXLE SPRING ASSEMBLY - 2 2
72 0170CO02CH C-166 ABRASADERA U U CLAMP - 2 2
0171CO02CH C-167 ABRASADERA U CM7 U CLAMP FOR CM7 2 - -
74 0000RF03GA C-168 RONDANA PLASTICA PLASTIC WASHER 1/2 14 14 14
76 0000CR01LZ C-169 PERNO LANZA LOCK PIN 1 1 1
77 SR18200EXT C-170 SEGURO R PIN AIR 1 1 1
80
0000BA104949
C-171 BALERO 104949 CM12 BALL BEARING 104949 CM12 - - 1
82
TCCS012GAL
C-173 TUERCA SEGURIDAD 1/2 LOCK NUT, 1/2 4 8 8
83
TCFS012GAL
C-174 TUERCA SEGURIDAD 1/2 NF LOCK NUT 1/2 NF 4 4 4
84 TCCN012GAL C-178 TUERCA NORMAL 1/2" NC NUT 1/2" NC 2 2 2
85 TCCN034GAL C-179 TUERCA NORMAL 3/4" NC NUT 3/4" NF 1 1 1
86 RNRX034GAL C-180 RONDANA PRESION 3/4" WASHER SPRING 3/4" 1 1 1
PULLEY INFORMATION
No. CODIGO CODE DESCRIPCION DE
PARTES DESCRIPTION OF PARTS
GAS
5.5
HP
GAS
8HP ELECTRIC .5&1.5 ELECTRIC 1&2 HP ELECTRIC 3 & 5HP ELECTRIC 7.5HP
21 POFG212034 C-126 POLEA 2 1/2" CAL 3/4" PULLEY 2 1/2"
CAL 3/4 1
POFG212100 C-127 POLEA 2 1/2" CAL 1" PULLEY 2 1/2"
CAL 1 1
POFG414058TK C-128 POLEA 4 1/4" CAL 5/8"
CUÑERO 3/16" PULLEY 4 1/4" CAL 5/8" KEY 3/16" 1
POFG414078TK C-175 POLEA 4 1/4" CAL 7/8"
CUÑERO 3/16" PULLEY 4 1/4" CAL 7/8" KEY 3/16" 1
POFG414118TK C-176 POLEA 4 1/4" CAL 1 1/8"
CUÑERO 1/4"
PULLEY 4 1/4"
CAL 1 1/8" KEY
1/4" 1
POFG414138TK C-177 POLEA 4 1/4" CAL 1 3/8"
CUÑERO 5/16"
PULLEY 4 1/4"
CAL 1 3/8" KEY
5/16" 1
THIS PARTS MANUAL APPLIES FOR CONCRETE MIXERS CM7, CM9, an CM12 FROM SERIAL NUMBER 36683
Discount-Equipment.com