TKB Home TZ74 User manual

This insert switch module in a transceiver which is a Z-Wave enabled device
and is fully compatible with any Z-Wave enabled network. Z-Wave enabled devices
displaying the Z-Wave logo can also be used with it regardless of the manufacturer,
and ours can also be used in other manufacturer's Z-Wave enabled networks.
Remote on/off control of the connected load is possible with other manufacturer's
wireless controller. Each module is designed to act as a repeater. Repeaters
will re-transmit the RF signal to ensure that the signal is received by its intended
destination by routing the signal around obstacles and radio dead spots.
TZ74-V1.1-2017 .4.5
A Z-Wave network can integrate devices of various classes made by different manufacturers.
The TZ74 can be incorporated into existing Z-Wave networks. The TZ74 module can be used
to carry out inclusion,association, or exclusion.
Minimum 40m in door 70m outdoor line of sight
AC110V～230V 50Hz/60Hz
868.4MHz(EU),908.4MHZ(US),921.4MHz(AU),869MHz(RU)
6A X 2
Insert two channel switch module
Note: This module must be“Included in the network”,and suitable for where it will be
permanently installed. The proper operation of this node in the mesh network is
dependent on it knowing it’s location with respect to other nodes. You can not "test
bench" configure this module, then install.
Wiring diagram
In the front casing, there is an on/off button with LED indicator which is used to
toggle switch on and off or carry out inclusion, exclusion, reset or association.
When first power is applied, its LED flashes on and off alternately and repeatedly
at 1-second intervals. It implies that it has not been assigned a node ID and can not
work with Z-Wave enabled devices.
The table below lists an operation summary of basic Z-Wave functions. Please
TM
refer to the instructions for your Z-Wave certificated primary con tr oller to
access the setup function, and to include/exclude/associate devices.
L: Line voltage input
NO1: Switched load1 output
S2: Connect to wall switch2 input
N: Line neutral
NO2: Switched load2 output
S1: Connect to wall switch1 input
COM: Load supply power Input
Interoperability with Z-WAVE devices
TZ74
-1-
-4-

-3-
-2-
The on/off knob allows the user
- Turn on or off the load attached
- Include or exclude the switch from the Z-Wave system
Programming
Configuration
Parameter Function Size
(Byte) Value Unit Default Description
1
2 1 1
Change the state
of indicator light
Memory function
1 10-1
0-1
Default status of socket
LED is on as indicator
when the load is off
Default with memory: the
socket status is same as
before when power on
to
3
Edge or Pulse
mode or Edge-
Toggle mode
1:Edge mode
2:Pulse mode
3:Edge-toggle mode
11-3 3
Product size (mm)
2. There are one groups for the switch
Each group can associate max five devices.
ID is excluded
1.The switch is not
connected to the
power
The switch isn’t working
and LED off
The switch LED illuminating,but
can not control the On/Off switch
of the load attached
The switch LED illuminating,but
the controler can not control the
switch
Group 1:lifeline
(Profile MSB=0x00,Profile LSB=0x01)
Set the On/Off
switch of the load
attached to on
On/Off
4
Invert switch In the edge mode
invert switch
1 0-1 0
Supported Command Class
COMMAND_CLASS_MANUFACTURER_SPECIFIC,
COMMAND_CLASS_DEVICE_RESET_LOCALLY,
COMMAND_CLASS_SWITCH_BINARY,
COMMAND_CLASS_BASIC,
COMMAND_CLASS_SWITCH_ALL,
COMMAND_CLASS_CONFIGURATION,
COMMAND_CLASS_SCENE_ACTIVATION,
COMMAND_CLASS_SCENE_ACTUATOR_CONF,
COMMAND_CLASS_MULTI_CHANNEL_V3,
COMMAND_CLASS_FIRMWARE_UPDATE_MD_V2