Planet FSD-804PS User manual

User's Manual
FSD-804PS
8-Port 10/100Mbps with
4-Port PoE
Web Smart Ethernet Switch
- 1 -

User’s Manual of FSD-804PS
Trademarks
Copyright ©PLANET Technology Corp. 2008.
Contents subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp. All other trademarks belong to their respective
owners.
Disclaimer
PLANET Technology does not warrant that the hardware will work properly in all environments and applications,
and makes no warranty and representation, either implied or expressed, with respect to the quality, performance,
merchantability, or fitness for a particular purpose.
PLANET has made every effort to ensure that this User’s Manual is accurate; PLANET disclaims liability for any
inaccuracies or omissions that may have occurred.
Information in this User’s Manual is subject to change without notice and does not represent a commitment on the
part of PLANET. PLANET assumes no responsibility for any inaccuracies that may be contained in this User’s
Manual. PLANET makes no commitment to update or keep current the information in this User’s Manual, and
reserves the right to make improvements to this User’s Manual and/or to the products described in this User’s
Manual, at any time without notice.
If you find information in this manual that is incorrect, misleading, or incomplete, we would appreciate your
comments and suggestions.
FCC Warning
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the Instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own expense.
CE Mark Warning
This is a Class A product. In a domestic environment, this product may cause radio interference, in which case the
user may be required to take adequate measures.
WEEE Warning
To avoid the potential effects on the environment and human health as a result of the presence of
hazardous substances in electrical and electronic equipment, end users of electrical and electronic
equipment should understand the meaning of the crossed-out wheeled bin symbol. Do not dispose of
WEEE as unsorted municipal waste and have to collect such WEEE separately.
Revision
PLANET 8-Port 10/100Mbps with 4-Port PoE Web Smart Ethernet Switch User's Manual
FOR MODEL: FSD-804PS
REVISION: 3.0(MAY .2008)
Part No.: 2080-A31120-005
- 2 -

User’s Manual of FSD-804PS
TABLE OF CONTENTS
1. INTRODUCTION.............................................................................................................5
1.1 CHECKLIST ................................................................................................................................................ 5
1.2 ABOUT THE SWITCH ................................................................................................................................... 5
1.3 FEATURES ................................................................................................................................................. 5
1.4 SPECIFICATION .......................................................................................................................................... 7
2. HARDWARE DESCRIPTION .........................................................................................9
2.1 FRONT PANEL ............................................................................................................................................ 9
2.2 REAR PANEL............................................................................................................................................ 10
2.3 HARDWARE INSTALLATION ........................................................................................................................ 11
2.4 DESKTOP INSTALLATION ........................................................................................................................... 12
2.5 RACK MOUNTING (OPTIONAL RACK KITS).................................................................................................. 13
2.6 PRODUCT APPLICATION ............................................................................................................................ 14
2.7 POWER OVER ETHERNET POWERED DEVICE ............................................................................................. 15
3 MANAGEMENT.............................................................................................................16
3.1 OVERVIEW ............................................................................................................................................... 16
3.2 REQUIREMENTS ....................................................................................................................................... 16
3.3 MANAGEMENT METHOD............................................................................................................................ 16
3.3.1 Web Management ........................................................................................................................................... 16
3.3.2 PLANET Smart Discovery Utility...................................................................................................................... 18
4. WEB CONFIGURATION ..............................................................................................20
4.1 MANIN MENU ........................................................................................................................................... 20
4.2 WEB PANEL ............................................................................................................................................. 21
4.3 SYSTEM................................................................................................................................................... 21
4.3.1 System Information.......................................................................................................................................... 22
4.3.2 IP Configuration............................................................................................................................................... 22
4.3.3 Password Setting............................................................................................................................................. 23
4.3.4 Firmware Upgrade ........................................................................................................................................... 24
4.3.5 Configuration Setting ....................................................................................................................................... 26
4.3.6 Alert Trap Configuration................................................................................................................................... 28
4.3.7 System Reboot ................................................................................................................................................ 29
4.4 PORT MANAGEMENT ................................................................................................................................30
4.4.1 Port Configuration............................................................................................................................................ 30
4.4.2 Port Status....................................................................................................................................................... 31
4.4.3 Port Security .................................................................................................................................................... 32
4.5 VLAN...................................................................................................................................................... 34
4.5.1 VLAN Group .................................................................................................................................................... 37
4.5.2 VLAN Per Port Setting ..................................................................................................................................... 41
4.5.3 VLAN setting example: .................................................................................................................................... 43
4.6 QUALITY OF SERVICE ............................................................................................................................... 49
4.6.1 802.1p Tag Priority Mode ................................................................................................................................50
4.6.2 DSCP QoS Mode............................................................................................................................................. 52
4.6.3 Port-Based Priority Mode................................................................................................................................. 54
4.7 STORM CONTROL..................................................................................................................................... 55
- 3 -

User’s Manual of FSD-804PS
4.8 MISC CONFIGURATION.............................................................................................................................. 56
4.9 POECONFIGURATION .............................................................................................................................. 58
4.10 LOGOUT................................................................................................................................................. 60
5. SWITCH OPERATION..................................................................................................61
5.1 ADDRESS TABLE ...................................................................................................................................... 61
5.2 LEARNING ................................................................................................................................................ 61
5.3 FORWARDING &FILTERING ....................................................................................................................... 61
5.4 STORE-AND-FORWARD............................................................................................................................. 61
5.5 AUTO-NEGOTIATION ................................................................................................................................. 61
6. POWER OVER ETHERNET OVERVIEW.....................................................................62
7. THE POE PROVISION PROCESS...............................................................................64
7.1 LINE DETECTION ...................................................................................................................................... 64
7.2 CLASSIFICATION....................................................................................................................................... 64
7.3 START-UP ................................................................................................................................................ 65
7.4 OPERATION.............................................................................................................................................. 65
7.5 POWER DISCONNECTION SCENARIOS........................................................................................................ 65
8.TROUBLESHOOTING...................................................................................................66
APPENDIX A NETWORKING CONNECTION .................................................................67
A.1 DATA OUT POESWITCH RJ-45 PORT PIN ASSIGNMENTS (PORT 1TO PORT-4)........................................ 67
A.2 SWITCH‘S RJ-45 PIN ASSIGNMENTS (PORT-5 TO PORT-8)......................................................................... 67
A.3 RJ-45 CABLE PIN ASSIGNMENT ................................................................................................................. 67
APPENDIX B....................................................................................................................69
B.1 POWER OVER ETHERNET COMPATIBILITY TEST .......................................................................................... 69
- 4 -

User’s Manual of FSD-804PS
1. INTRODUCTION
1.1 Checklist
Check the contents of your package for following parts:
FSD-804PS x1
User's manual CD x1
Quick installation guide x1
Power cord x 1
Rubber feet x 4
If any of these pieces are missing or damaged, please contact your dealer immediately, if possible, retain the carton
including the original packing material, and use them against to repack the product in case there is a need to return it to
us for repair.
1.2 About the Switch
The FSD-804PS is equipped with unshielded twisted-pair (UTP) cable ports providing dedicated 10 or 100Mbps band-
width. The FSD-804PS supports MDI/ MDI-X convertible on 8-10/100Mbps ports, also provide PoE inject function on
port#1, 2, 3, 4, which is able to drive 4 IEEE 802.3af compliant powered devices. The dual speed ports use standard
twisted-pair cabling and are ideal for SOHO or segmenting networks into small. Each 10/100Mbps port can supports up to
200Mbps of throughput in full-duplex mode, the FSD-804PS also provides a simple, cost-effective, and highly reliable
network connection for data as well as power. Furthermore, it is the ideal device for bridging among Ethernet, Fast Ethernet
workgroups and networks.
With 4 PoE interfaces, the FSD-804PS is ideal for small business and workgroups requiring to deploy the PoE for the
wireless access points, IP-based surveillance camera or IP phones in any places easily, efficiently and cost effective.
The front panel of FSD-804PS provides LEDs for easy recognition of the switch operation status and troubleshooting.
These LED indicators display the power status for the system, LNK/ACT and speed for each10/100M port. Also the PoE in
use LED indicates for PoE ports (port#1 to port#4).
With data and power over Ethernet from one unit, the FSD-804PS shall reduce cables and eliminates the need for dedi-
cated electrical outlets on the wall, ceiling or any unreachable place. A wire carries both data and power lowering the
installation costs, simplifying the installation effort and eliminating the need for electricians or extension cords. We are also
proud of the key feature – energy saving. With more efficient switching power supply, the efficiency of the FSD-804PS
would be much better than four linear power adapters in a long run.
The smart functions make it easy to survey and control the PoE power provision to the devices by the Web interface. Basic
switching functions such as VLAN, bandwidth control and QoS are available for network management.
1.3 Features
■ Interface
8-Port 10/100Mbps Fast Ethernet ports
4-Port support 48VDC power to PoE Powered Device
PoE
Complies with IEEE 802.3af Power over Ethernet End-Span PSE
Up to 4 IEEE 802.3af devices powered
Support PoE Power up to 15.4 watts for each PoE ports
Auto detect powered device (PD)
Circuit protection prevent power interference between ports
- 5 -

User’s Manual of FSD-804PS
Remote power feeding up to 100m
PoE Management
Total PoE power budget control
Pert port PoE function enable/disable
PoE Port Power feeding priority
Per PoE port power limit
PD classification detection
Management
Web interface for remote management
Firmware upgrade through Web interface
PLANET Smart Discovery utility automatically finds PLANET devices on the network
SNMP Trap for alarm notification of events
Switching
Hardware based 10/100Mbps auto-negotiation
Flow control for full duplex operation and back pressure for half duplex operation
Integrates address look-up engine, support 1K absolute MAC addresses
Automatic address learning and address aging
Supports Auto MDI/MDI-X function
VLAN for network segregation
Hardware
10-inch desktop size, rack mountable; 1U height
Reset button for reset to default setting and system reboot
LED indicators for POE ready and POE activity
Optional Rack Ear Accessories Kit for 10-inch cabinet (RKE-10A) and 19-inch cabinet (RKE-10B)
Standard Compliance
IEEE 802.3 10Base-T
IEEE 802.3u 100Base-TX
IEEE 802.3af Power over Ethernet
FCC Part 15 Class A, CE
- 6 -

User’s Manual of FSD-804PS
1.4 Specification
Model FSD-804PS
Hardware Specification
Network Connector 8-Port RJ-45 for 10/100Base-TX
PoE Inject Port 4-Port with PoE injector function, Port-1 to Port-4
LED Display One power, 1-4 port PoE in-use, LNK/ACT
5-8 port LNK/ACT
Switch Architecture Store and Forward switch architecture
Switch Fabric 1.6Gbps
MAC Address 1K MAC address table with Auto learning function
Throughput 1.19Mbps
Remote power feeding End-point insert type and compatible with IEEE 802.3af Per port feeding power: 48V DC, 15.4W, 350mA (Maximum)
(Pin 1, 2, 3, 6)
Power AC 100~240V, 50/60Hz,
Power Consumption Max. 65 watts / 221 BTU
Dimension (W x D x H) 217 x 135 x 43 mm
Weight 1.0 kg
Power over Ethernet
PoE Standard IEEE 802.3af Power over Ethernet / PSE
PoE Power Supply Type End-Span
PoE Power Output Per Port 48V DC, 350mA . Max. 15.4 watts
Power Pin Assignment 1/2(+), 3/6(-)
Power Budget 55 watts
Layer 2 Function
Management Web management, SNMP Trap
VLAN Port-Based VLAN and IEEE 802.1Q Tag-Based VLAN, up to 16 VLAN groups
QoS 2 priority queues for three type of Class of Service
•Port-Based
•IEEE 802.1p priority tag
•TCP/IP header’s DSCP classifier
Weighted Round Robin queue scheduling
Bandwidth Control Inbound Rate Limit and Outbound Traffic shaping
Storm Control Disable, 12.5%, 25%, 50%, 62.5% 4 levels
Standard Conformance
EMI Safety FCC Class A, CE
Operating environment 0~40 degree C, 10%~95%RH
Storage environment -40 ~70 degree C, 95% RH
- 7 -

User’s Manual of FSD-804PS
- 8 -
Operating Humidity 5% to 90% , relative humidity, non-condensing
Storage Humidity 5% to 90% , relative humidity, non-condensing
Standard Compliance IEEE 802.3
IEEE 802.3u
IEEE 802.3x
IEEE 802.3af
IEEE 802.1p
IEEE 802.1Q
Ethernet
Fast Ethernet
Flow Control
Power over Ethernet
Class of Service
VLAN Tagging

User’s Manual of FSD-804PS
2. HARDWARE DESCRIPTION
This product provides two different running speeds – 10Mbps, 100Mbps in the same Switch and automatically distin-
guishes the speed of incoming connection.
This section describes the hardware features of FSD-804PS. For easier management and control of the Switch, familiarize
yourself with its display indicators, and ports. Front panel illustrations in this chapter display the unit LED indicators. Before
connecting any network device to the FSD-804PS, read this chapter carefully.
In the following section, the term “PoE Switch” means the Web Smart PoE switch device, ie. FSD-804PS; term of
“switch” can be any third switches.
2.1 Front Panel
The Front Panel of the FSD-804PS PoE Web Smart Ethernet Switch consists of 8x Auto-Sensing 10/100Mbps Ethernet
RJ-45 Ports. The LED Indicators are also located on the front panel of the FSD-804PS.
Front Panel of FSD-804PS ( Hardware version 3)
Figure 2-1 FSD-804PS Switch front panel
■ Reset Button
At the left of front panel, the reset button is designed for reboot the PoE Switch without turn off and on the power.
Figure 2-2 Reset button of FSD-804PS
To press the RESET button about 10 seconds and then release. The PoE Switch will back to the
factory default mode. Be sure that you backup the current configuration of PoE Switch; else the
entire configuration will be erased when pressing the “RESET” button.
- 9 -

User’s Manual of FSD-804PS
The following is the summary table of Reset button functions:
Reset Button Pressed and Released Function
About 1 second Reboot the PoE Injector Hub
Until the SYS LED lit off
Reset the PoE Switch to Factory Default configuration. The
PoE Switch will reboot and load the default IP settings as
below:
。 Default Password: admin
。 Default IP address: 192.168.0.100
。 Subnet mask: 255.255.255.0
。 Default Gateway: 192.168.0.254
2.1.1 LED indicators
■ System
LED Color Function
PWR Green Lights to indicate that the PoE Switch has power.
■ Per 10/100Mbps port
LED Color Function
PoE in-use Green Lights to indicate the port is providing 48VDC in-line power. (1-4 ports)
LNK/ACT Green Lit: indicate the link through that port is successfully established.
Blinks to indicate that the Switch is actively sending or receiving data over that port.
1. Press the RESET button once. The Switch will reboot automatically.
2. Press the RESET button for 5 seconds. The Switch will back to the factory default mode; the
entire configuration will be erased.
2.2 Rear Panel
The rear panel of the FSD-804PS indicates an AC inlet power socket, which accepts input power from 100 to 240VAC,
50-60Hz. And have a fan hole on the rear panel.
Figure 2-3 FSD-804PS Switch rear panel
Power Notice:
1. The device is a power-required device, it means, it will not work till it is powered. If your networks
should active all the time, please consider using UPS (Uninterrupted Power Supply) for your device.
It will prevent you from network data loss or network downtime.
2. In some area, installing a surge suppression device may also help to protect your FSD-804PS
from being damaged by unregulated surge or current to the FSD-804PS or the power adapter.
- 10 -

User’s Manual of FSD-804PS
2.3 Hardware Installation
2.3.1 Before start up
Before your installation, please refer to the followings for your cabling:
100Base-TX
All 100Base-TX ports come with Auto-Negotiation capability. They automatically support 100Base-TX and 10Base-T
networks. Users only need to plug a working network device into one of the 100Base-TX ports, and then turn on the
FSD-804PS. The port will automatically runs in 10Mbps, 20Mbps, 100Mbps or 200Mbps after the negotiation with the
connected device.
Cabling
Each 10/100Base-TX ports use RJ-45 sockets -- similar to phone jacks -- for connection of unshielded twisted-pair
cable (UTP). The IEEE 802.3u Fast Ethernet standard requires Category 5 UTP for 100Mbps 100Base-TX. 10Base-T
networks can use Cat.3, 4, or 5 UTP (see table below). Maximum distance is 100meters (328 feet).
Port Type Cable Type Connector
10Base-T Cat 3, 4, 5, 2-pair RJ-45
100Base-TX Cat.5 UTP, 2-pair RJ-45
Any Ethernet devices like hubs/ PCs can connect to the FSD-804PS by using straight-through wires. The
eight-10/100Mbps ports are auto-MDI/MDI-X can be used on straight-through or crossover cable.
- 11 -

User’s Manual of FSD-804PS
2.4 Desktop Installation
To install the Switch on desktop, simply follow the next steps:
Step1: Attach the rubber feet to the recessed areas on the bottom of the Switch, as shown in Figure 2-4.
Figure 2-4 Attaching the rubber feet to the Switch
Step2: Place the Switch on desktop near an AC power source.
Step3: Keep enough ventilation space between the Switch and the surrounding objects.
:
When choosing a location, please keep in mind the environmental restrictions discussed in Chapter
1, Section 4, in Specification.
Step4: Connect your Switch to network devices.
A. Connect one end of a standard network cable to the 10/100 RJ-45 ports on the Back of the Switch.
B. Connect the other end of the cable to the network devices such as printer servers, workstations or routers…etc.
Connection to the Switch requires UTP Category 5 network cabling with RJ-45 tips. For more in-
formation, please see the Cabling Specification in Appendix A.
Step5: Supply power to the Switch.
A. Connect one end of the power cable to the Switch.
B. Connect the power plug of the power cable to a standard wall outlet.
When the Switch receives power, the Power LED should remain solid Green.
- 12 -

User’s Manual of FSD-804PS
2.5 Rack Mounting (Optional Rack Kits)
To install the Switch in a 10-inch or 19-inch standard rack, PLANET provides the optional rack mount kits RKE-10A /
RKE-10B for different need. Follow the instructions described below.
Step1: Place your Switch on a hard flat surface, with the front panel positioned towards your front side.
Step2: Attach a rack-mount bracket to each side of the Switch with supplied screws attached to the package. Figure 2-5
shows how to attach brackets to one side of the Switch.
Figure 2-5 Attaching the brackets to the Switch.
You must use the screws supplied with the mounting brackets. Damage caused to the parts by
using incorrect screws would invalidate the warranty.
Step3: Secure the brackets tightly.
Step4: Follow the same steps to attach the second bracket to the opposite side.
Step5: After the brackets are attached to the Switch, use suitable screws to securely attach the brackets to the rack, as
shown in Figure 2-6.
Figure 2-6 Mounting the Switch in a Rack
Step6: Proceeds with the steps 4 and steps 5 of session 2.4 Desktop Installation to connect the network cabling and
supply power to your Switch.
- 13 -

User’s Manual of FSD-804PS
2.6 Product Application
2.6.1 Connecting end node or Switch
1. Place the FSD-804PS on a smooth surface or fasten the mounting brackets purchased separately with the pro-
vided screws in a standard 19” rack.
2. Connect the power cord to the power inlet socket of FSD-804PS and the other end into the local power source
outlet. When the Switch receives power, the Power LED should remain solid Green.
3. Connect other switch or PC to one port of the FSD-804PS using Category 3/4/5 UTP/STP cabling.
4. Connect another switch or PC to the other port of FSD-804PS by following the same process as described in Step
3.
Figure 2-7 End node or Switch connection
Cable distance for Switch
The cable distance between the FSD-804PS and PC should not exceed 100 meter for UTP/STP
cable.
Make sure the wiring is correct
It can be used Category 3/4/5 cable in 10 Mbps operation. To reliably operate your network at
100Mbps, you must use an Unshielded Twisted-Pair (UTP) Category 5 cable, or better Data Grade
cabling. While a Category 3 or 4 cables may initially seem to work, it will soon cause data loss.
- 14 -

User’s Manual of FSD-804PS
2.6.2 As a department / workgroup PoE Switch
Providing up to 4 PoE, in-line power interface, the Switch can easily build a power central-controlled IP phone system,
IP Camera system, AP group for the enterprise. For instance, 4 camera / AP can be easily installed around the corner
in the company for surveillance demands or build a wireless roaming environment in the office. Without the
power-socket limitation, the switch makes the installation of cameras or WLAN AP more easily and efficiently.
Figure 2-8 PoE Switch connection
2.7 Power over Ethernet Powered Device
3~5 watts
Voice over IP phones
Enterprise can install POE VoIP Phone, ATA and other Ethernet/non-Ethernet
end-devices to the central where UPS is installed for un-interrupt power system
and power control system.
6~12 watts
Wireless LAN Access Points
Museum, Sightseeing, Airport, Hotel, Campus, Factory, Warehouse can install
the Access Point any where with no hesitation
10~12 watts
IP Surveillance
Enterprise, Museum, Campus, Hospital, Bank, can install IP Camera without
limits of install location – no need electrician to install AC sockets.
3~12 watts
PoE Splitter
PoE Splitter split the PoE 48V DC over the Ethernet cable into 5/9/12V DC
power output. It frees the device deployment from restrictions due to power
outlet locations, which eliminate the costs for additional AC wiring and reduces
the installation time.
- 15 -

User’s Manual of FSD-804PS
3 MANAGEMENT
This chapter describes how to manage the PoE Switch. Topics include:
- Overview
- Management method
- Logging on to the Web Smart Switch
3.1 Overview
The Web Smart PoE Switch provides a user-friendly, Web interface. Using this interface, you can perform various device
configuration and management activities, including:
System
Power over Ethernet
Tools
3.2 Requirements
Network cables.
Use standard network (UTP) cables with RJ45 connectors.
Subscriber PC installed with Ethernet NIC (Network Card)
Workstations of subscribers running Windows 98/ME, NT4.0, 2000/2003/XP, MAC OS X or later, Linux, UNIX
or other platform compatible with TCP/IP protocols.
Above PC installed with WEB Browser and JAVA runtime environment Plug-in
It is recommended to use Internet Explore 6.0 or above to access Web Smart Switch.
3.3 Management Method
User can manage the PoE Switch by Web Management via a network connection.
3.3.1 Web Management
The PoE Switch can be configured through an Ethernet connection, make sure the manager PC must be set on same the
IP subnet address with the PoE Switch.
For example, if you have changed the default IP address of the Device to 192.168.99.123 with subnet mask 255.255.255.0
via console, then the manager PC should be set at 192.168.99.x (where x is a number between 2 and 254) with subnet
mask 255.255.255.0. Or you can use the factory default IP address 192.168.0.100 to do the relative configuration on
manager PC.
- 16 -

User’s Manual of FSD-804PS
1. Use Internet Explorer 5.0 or above Web browser. Enter IP address http://192.168.0.100 (the factory-default IP ad-
dress or that you have changed via console) to access the Web interface.
Figure 3-1 Web Management over Ethernet
2. When the following login screen appears, please enter the default username "admin" and password “admin” (or
the password you have changed via console) to login the main screen of PoE Switch. The login screen in Figure 3-2
appears.
Default IP Address: 192.168.0.100
Default Account: admin
Default Password: admin
Figure 3-2 Login screen
1. For security reason, please change and memorize the new password after this first setup.
2. Only accept command in lowercase letter under WEB interface.
- 17 -

User’s Manual of FSD-804PS
3.3.2 PLANET Smart Discovery Utility
For easily list the Switch in your Ethernet environment, the Planet Smart Discovery Utility from user’s manual CD-ROM is
an ideal solution.
The following install instructions guiding you for run the Planet Smart Discovery Utility.
1. Deposit the Planet Smart Discovery Utility in administrator PC.
2. Run this utility and the following screen appears.
Figure 3-3 PLANET Smart Discovery Utility Screen
If there are two LAN cards or above in the same administrator PC, choose different LAN card by use the
“Select Adapter” tool.
3. Press “Refresh” button for list current connected devices in the discovery list, the screen is shown as follow.
Figure 3-4 PLANET Smart Discovery Utility Screen
- 18 -

User’s Manual of FSD-804PS
4. This utility show all necessary information from the devices, such as MAC Address, Device Name, firmware version,
Device IP Subnet address, also can assign new password, IP Subnet address and description for the devices.
5. After setup completed, press “Update Device”, “Update Multi” or “Update All” button to take affect. The meaning
of the 3 buttons above are shown as below:
Update Device: use current setting on one single device.
Update Multi: use current setting on choose multi-devices.
Update All: use current setting on whole devices in the list.
The same functions mentioned above also can be finding in “Option” tools bar.
6. To click the “Control Packet Force Broadcast” function, it can allow assign new setting value to the Switch under
different IP subnet address.
7. Press “Connect to Device” button then the Web login screen appears in Figure 3-2.
8. Press “Exit” button to shutdown the planet Smart Discovery Utility.
- 19 -

User’s Manual of FSD-804PS
4. WEB CONFIGURATION
The Switch provide Web interface for PoE smart function configuration and make the Switch operate more effectively -
They can be configured through the Web Browser. A network administrator can manage and monitor the Switch from the
local LAN. This section indicates how to configure the Switch to enable its smart function.
4.1 Manin Menu
After a successful login, the main screen appears. The main screen displays the product name the function menu, and the
main information in the center. As showed in Figure 4-1.
Figure 4-1 main menu screen
The four items and it description shown as below:
System: Provide System information and configuration of Switch. Explained in section 4.3.
Port Management Setup per port mode, Rate Limit, Port description. Explained in section 4.4.
VLAN Configure VLAN Member / Port Configuration. Explained in section 4.5.
Quality of Service Mapping the packet level to classify the packets priority. Explained in section 4.6.
Storm Control Enable Storm Control function to reduce broadcast packets on the Switch.
Explained in section 4.7.
Misc Configuration Configure MAC address table aging, aging time mode and port flow control. Explained
in section 4.8.
PoE Configuration Provide PoE Management configuration of Switch. Explained in section 4.9.
Logout: Provide Logout function of Switch.
- 20 -