TMI Products VD53C User manual

Issued on : 15. Jan. 2016
ψ29. 50 mm
H 4. 57 mm
Specification - 1
Specification - 2
Appearance
Casing
Hand Fitting - 1
Hand Fitting - 2
Hand Setting Stem
Dial - 1
Dial - 2
Dial - 3
Dial - 4
Dial - 5
Dial - 6
Assembly Plan - 1
Assembly Plan - 2
Assembly Plan - 3
Assembly Plan - 4
Hands
SII Products
Cal. VD53C
Version 1
Version 1
Version No.
Version 1
Version 1
Version 1
Version 1
Version 1
Version 1
Version 1
Version 1
Version 1
Version 1
Version 1
Version 1
Item
Version 1
Version 1
Version 1
Version 1

MOVEMENT SPECIFICATION - 1
CAL.VD53C 12 3 / 4 Ligne Quartz Movement
Three Hands with 3 Eyes / Date ( Minute, 1 / 1 Second Chronograph, 24H Indicator & Calendar )
1. MOVEMENT DIMENSIONS
·
Outside diameter ψ29.50mm
(12H~6H) x 26.00mm (3H~9H)
·
Casing diameter ψ28.80mm
(12H~6H)
·
Total height 4.57 mm
·
Dimensions of small hands away from center 7.50 mm
2. TIME STANDARD
·
Type of quartz oscillator Tuning fork
·
Frequency of quartz oscillator 32,768 Hz
·
Accuracy Monthly rate: Less than 20 seconds per month at
normal temperature range
·
Regulation device Nil
·
Regulation hands unbalance Second : Less than 0.09 µN·m ( 9mg·mm )
Minute : Less than 0.60 µN·m ( 60mg·mm )
Hour : Less than 0.50 µN·m ( 50mg·mm )
Chronograph hands : Less than 0.05 µN·m ( 5mg.mm )
24 hour indicator : Less than 0.07 µN·m ( 7mg.mm )
·
The moment of inertia 24 hour indicator : Less than 0.40 µg·m² ( 400mg·mm² )
(Disc hand)
·
Additional function Stopwatch : up to 60 minutes in 1 second split time
24 hour indicator ( synchronized regular hour-hand )
3. BATTERY
·
Type Silver oxide battery
·
Nominal voltage 1.55 V
·
Size ψ9.5 x t 2.0 ( mm )
·
Battery life Approx. 3 years
·
Recommended battery SR920SW ( SEIZAIKEN )
4. DIAL FIXED METHOD
The dial is fixed by two dial leg holes of the main plate
5. JEWEL
0 jewel
6. ANTIMAGNETISM
≧1600 A / m
( direct current magnetic field )
7. SHOCK RESISTANCE
On equal level with general quartz movement
8. OPERATING TEMPERATURE RANGE From - 5 ℃to + 50 ℃
9. TEST OF ACCURACY
·
Equipment to be used SEIKO Quartz Tester QT - 99
Greiner Quartz Timer - C
Witschi Q-Tester 4000
·
Duration of measurement 10 seconds
·
Microphone to be used Electromagnetic detection type
* All specifications are subject to change without notice.
SII Products
Version: 1

Movement Specification - 2
OPERATION 2 step motors ( 3 hands with calendar, 1 / 1 sec. chrono. maximum to 60 minutes )
1st click
2nd click
adjusting calendar
adjusting minute, hour & chrono. hands
( clockwise )
* Pull the crown to 2nd click to adjust the stopwatch hand position.
* AC functions is available if stopwatch hand position is disorderly.
* When using AC functions, stopwatch hand moves back and returned to where it was
( second hand moves 1/2 circle counterclockwise and 1/2 circle clockwise )
Version 1
SII Products
CAL. VD53C
date
stopwatch
second hand
stopwatch
minute hand 3 hands
Normal position
START
STOP
ADJUSTING
CALENDAR
SPLIT
RESET
AC FUNCTIONS
( KEEP
BUTTONS
"A" AND "B"
PRESSED AT
THE SAME TIME
FOR 2
SECONDS, AND
THEN, RELEASE
THE BUTTONS )
START
STOP
FREE
24H hands
linkage
linkage
SPLIT
RESET
ADJUSTING THE
STOPWATCH SEC.& MIN.
HAND POSITION
(CLOCKWISE )
TIMING SETTING
RESET SWITCH
SECOND SETTING
ADJUSTING THE
STOPWATCH SEC. & MIN.
HAND POSITION
(COUNTERCLOCKWISE )

         
中心柱位
                         

     
與機芯平面之最大高度
                       
機芯總高度
    
一般針高
    
高針
         !
特高針A/特高針B

    
一般針高
    
高針
        
時針輪
         
分針輪
          
秒針輪
                    
計時分針輪
! " #        #$  
小時針輪
    
一般針高
    
高針
% & '  (
一般針高
% & '  )
高針
           *  +   ,    
計時秒針輪

      
特高針A
              

   
計時秒針輪
      
特高針B
                

   
計時分針輪
   

   
時針輪
     

   
分針輪

    

   
秒針輪
      
特高針A
      
特高針B
            

   
小時針輪