TMI Products VJ32B Installer manual

SII Products
ANALOGUE QUARTZ
TECHNICAL GUIDE
&
PARTS CATALOGUE
Cal.VJ32B
Cal.VJ34B
Revised on : 05. Jun. 2018

[SPECIFICATION]
φ23.70 mm
22.60 mm : between 12 o'clock and 6 o'clock sides
22.60 mm : between 3 o'clock and 9 o'clock sides
φ23.30 mm
22.10 mm : between 12 o'clock and 6 o'clock sides
21.40 mm : between 3 o'clock and 9 o'clock sides
Electronic circuit reset switch
Electronic circuit reset switch
Second setting device Date setting
Date setting
Use 10-second gate
* Set the winding stem with crown at the normal position
SR621SW (Silver oxide battery)
Battery life is approximately 3 years
PARTS CATALOGUE / TECHNICAL GUIDE
Movement
1
Battery
Measuring gate by
quartz tester
Outside diameter
Casing diameter
Movement
size
Additional mechanism
Time indication
Driving System
Step motor （Load compensated driving pulse system type）
3 Hands
Calendar
2 Hands
Calendar
SII Products
Item
Version-02
VJ34B
VJ32B
VJ34B
Total height
2.71 mm ( including the battery )
VJ32B
Loss/Gain (Monthly rate)
Frequency of crystal oscillator
Less than ±20seconds at normal temperature range
32,768 Hz
Jewels
0 Jewel
Operational temperature range
- 5℃~ + 50℃
Regulation system
Nil
Cal. No.

Lubricating : Types of oil Oil quantity
Moebius 9010
Moebius 9030
*Refer to the 4pages for the each parts code
Hour , minute and second hands
Dial
0808 044
Date dial guard
Date dial *
0810 890
Date jumper
0273 021
Hour wheel
0802 030
Date driving wheel
2
SII Products
Version-03
Cal.VJ32/34B
PARTS CATALOGUE
Disassembling procedures Figs.
①
NORMAL QUANTITY
⑦
②
①
⑥
④
⑤
→
Reassembling procedures Figs.
㉘
③
→
①
㉘

Battery
0351 332
Winding stem
4004 303
Circuit block with coil block
0016 121
* Battery connection (+)
0701 170
Fifth wheel and pinion
0231 066
Third wheel and pinion
4216 088
Insulator
4146 126
0033 219
Step rotor
Reset pin
4270 385
Battery connection (-)
0806 142
4239 062
0391 041
Rotor stator
0281 041
Setting wheel
0033 220
Pin for setting wheel
0125 297
Train wheel bridge
0221 055
0261 291
Center wheel and pinion
0282 089
Clutch wheel
< VJ32B / VJ34B >
*Refer to the 4pages for the each parts code
㉒
Date corrector wheel
⑰
⑫
⑳
⑲
⑬
* Fourth wheel and pinion
PARTS CATALOGUE
Version-06
Cal.VJ32/34B
⑧
⑨
⑮
⑩
Screw for
Battery
connection (+)
⑪
⑱
⑯
㉑
㉓
Train wheel setting
lever
㉕
*2 Oiling position
⑭
㉔
SII Products
3
㉘
㉖
Minute wheel and pinion
*1 Oiling position
㉗
*1
*2

Date dial
O The part which is not common in Cal.VJ32B/VJ34B
*All parts cord are subject to change without notice.
Version-03
Cal.VJ32/34B
PARTS CATALOGUE
Positing of
crown
Positing of
date frame
Color of figure
Color of
background
4
3H
3H
White
Black
White
Black
Black
White
6H
Black
Battery connection(+)
4268 049
4268 054
6H
SII Products
3H
Parts name
VJ32B
VJ34B
0144 097
0144 088
White
⑪
⑯
Fourth wheel and pinion
3H
④
Part code
0878 159
0878 153
0878 157
0878 158
3H
3H

The explanation here is only for the particular points of Cal.VJ32 / VJ34
Ⅰ. STRUCTURE OF THE CIRCUIT BLOCK
Notes: Since the circuit block and coil block are made by one piece, in disassembling and
reassembling take care not to cut the coil line.
Crystal unit
Input terminal(+)
C-MOS-IC
Coil block
Input terminal(-)
Ⅱ. REMARKS ON DISASSEMBLING AND REASSEMBLING
Hands
How to install
Place the movement directly on a flat metal plate or the like
to install the hands.
Date dial guard
The date dial guard has three protrusions to be caught under the main plate, and it is also fixed
by two guide pins.
・How to remove
Lightly lift the A portion of the date dial guard with
tweezers to release it from the guide pin, and then
move it in the clockwise direction until it gets off
the guide pin.
Release the B portion of the date dial guard in the
same way as described above, and then move it in
the clockwise direction until gets off the guide pin.
Check that all the three protrusions of the date dial
guard have come off from the main plate, and then
remove the date dial guard.
Version-03
Cal.VJ32/34B
TECHNICAL GUIDE
②
5
①
3)
1)
2)
SII Products
Metal plate
A portion
B portion
Protrusion
Date dial guard
Guide pin
Tweezers

・How to install
Protrusion C Protrusion D
Put the date dial guard on the main plate so that B portion
the A and B portion are over the guide pins,
as shown in the illustration at right.
Move the protrusion D of the date dial guard in the
counterclockwise direction so that it is caught
under the main plate.
Slightly move the protrusions C and E in the
counterclockwise direction alternately to set Protrusion E A portion
them under the main plate. Then, set the
A and B portions of the date dial guard to
the guide pins.
Check that the date dial guard is fixed
securely to the main plate.
Battery
・How to install battery
Insert the Battery aslant in the direction shown by the arrow.
Check the Battery connection (+) securely touches the side
face of the Battery.
Coil block
Correct
Battery Main plate
Battery connection (+)
Battery connection (+)
・How to install
Have the hook portions ( 3 places) catch the main plate ( Fig.1 & Fig.2).
In disassembling and reassembling, take care not to deform the hook portion.
After installing the Battery connection (+), check that the three hook portions securely catch the main plate.
Tweezers
Hook portion
Main plate
Hook portion
Hook portion
[ Fig.1 ]
[ Fig.2 ]
SII Products
Version-02
Cal.VJ32/34B
TECHNICAL GUIDE
3)
6
1)
2)
4)
③
④
Main plate

Insulator
・Setting position
Notes: To Insulate between the Battery connection (+) and the Battery connection (-),
Insulator should be put at the three pin securely as bellow.
Pin
Insulator
Train wheel bridge
・Setting position
Notes: Since the fifth wheel and pinion and step rotor are made of plastics, take care not to damage
them in disassembling and reassembling. Fourth wheel and pinion
Minute wheel and pinion
Setting wheel
Pin for setting wheel
Fifth wheel and pinion
Setting wheel Step rotor
Third wheel and pinion
Clutch wheel
Step rotor Third wheel and pinion Minute wheel and pinion
Reset pin
Fifth wheel and pinion
Center wheel and pinion
Train wheel setting lever
・Setting position
Notes:
・Catch the part of spring of the Train wheel setting lever to the pin like as below.
・Take care not to deform the spring potion of the Train wheel setting lever.
Train wheel setting lever
⑥
⑦
7
SII Products
Version-02
Cal.VJ32/34B
TECHNICAL GUIDE
⑤
Fourth wheel and pinion Clutch wheel

Pin for setting wheel
Notes:
In disassembling and reassembling, take care not to damage the portion that is assembled of the pin.
( Since the portion that is assembled of the pin is made of plastics and easily damaged.)
In disassembling,
pick the pin up main plate to vertical direction with care.
Tweezers
Pin for setting wheel
Center wheel and pinion
Minute wheel and pinion
In reassembling,
push the pin in main plate to vertical direction with care.
Pin for setting wheel Main plate
Setting wheel (The portion that is assembled of the pin)
Minute wheel and pinion Center wheel and pinion
⑧
8
Version-03
Cal.VJ32/34B
TECHNICAL GUIDE
SII Products