Toa 9000M2 Series User manual

9000M2 Series
Quick Start Guide
- Auto-mixing -
Conference/Courtroom Using Simultaneous Mode
1/33

System Overview
This application is composed of a Main room and an AUX conference room. MIC 1, used by a
chairperson every time, has the priority over the other inputs. Audio source is always output to
Main Room Zone 1 , Main Room Zone2 , Aux Conference Room, Webcast, phone and
recording device. Level of microphones can be controlled by remote controller and output
volume of each area is also adjustable by remote controller when needed.
System Components
1．A-9120DHM2 x 1
2．ZM-9012 x 4
3．ZM-9013 x 1
4．D-001T x 4
5．T-001T x 2
6．RC-001T x 1（with AD-246）
7．DM-1300US x 6
8．PC Audio x 1
9．Phone x 1
10．Recording device x 1
11．P-912MK2 x 1
12．F-122CU2
Setting
Input 1 (D-001T): DM-1300US (Priority 1)
Input 2 (D-001T): DM-1300US (Priority 2)
Input 3 (D-001T): DM-1300US
Input 4 (D-001T): DM-1300US
Input 5 (D-001T): DM-1300US
Input 6 (D-001T): DM-1300US
Input 7 (D-001T): PBX (Priority 2)
Input 8 (D-001T): PC Audio
2/33

Output 1 (A-9120DHM2): Main Room Zone 1
Output 2 (A-9120DHM2): Main Room Zone 2
Output 3 (T-001T - P-912MK2): Aux Conference Room 1
Output 4 (T-001T): Webcast
Output 5 (T-001T): Phone
Output 6 (T-001T): Recording device
Remote out (RC-001T) : ZM-9013[0] >> ZM-9012[1] >> ZM-9012[2] >>
ZM-9012[3] >> ZM-9012[4]
Button Configuration
ZM-9013[0]: Main room
Button 1: Input 3 on/off
Button 2: Input 4 on/off
Button 3: Input 5 on/off
Button 4: Input 6 on/off
Button 5: Input 8 on/off
ZM-9012[1]: Rack room
Changing the input volume.
ZM-9012[2]: Main room 1
Changing the output volume.
ZM-9012[3]: Main room 2
Changing the output volume.
ZM-9012[4]: Aux Conference Room 1
Changing the output volume.
3/33

Configuration
4/33

1. The following is the initial setting wizard screen.
. Click “ New File” on the Start Menu window.
2
5/33

6/33
3. Set module configurations.
4. Select the modules to be inserted into the amplifier’s slots from the pull-down menu in the
Module field.

5. Select a module for each slot. At the same time, please name each channel (ex. “MIC 1”).
Main Frame Name 1 >> ”ZONE1” Name 2 >> ”ZONE2”
Slot #1 >> D-001 Name 1 >> “MIC1” Name 2 >> “MIC2”
Slot #2 >> D-001 Name 1 >> “MIC3” Name 2 >> “MIC4”
Slot #3 >> D-001 Name 1 >> “MIC5” Name 2 >> “MIC6”
Slot #4 >> D-001 Name 1 >> “PHONE” Name 2 >> “PC”
Slot #5 >> T-001 Name 1 >> “AUXROOM” Name 2 >> “WEBCAST”
Slot #6 >> T-001 Name 1 >> “PHONE” Name 2 >> “RECORD”
Slot #7 >> None
Slot #8 >> RC-001
6. Click the “NEXT” button when finished.
7/33

7. The following window is for setting devices connected to REMOTE VOLUME terminal on
9000M2 rear panel o e ZM-9001, ZM-9002 o -9003, select “NONE”. If you d not us r ZM from the
2
combo box “TYPE”.
8. In this “Auto-mixing “application, select NONE for both REMOTE VOL1 and REMOTE VOL
8/33

9. Click “FINISH” button.
10. Setting for Remote Controller: ZM-9011/9012/9013/9014.
9/33

11. Select the number of Remote Controllers you will use.
In this application, select “5”.
10/33

12. Select “ZM-9013” from the combo box “MODEL” for ADDRESS0, “ZM-9012” for ADDRESS
If “CROSS POINT CHANGE” function will be assigned to a button of Remote Controller, select
either type of “SOURCE SELECTION MODE”.
EXCLUSIVE MODE: A single cross point can be turned ON for each output channel.
SIMULTANEOUS MODE: Multiple cross points can be arbitrarily turned ON.
Here, check “SIMULTANEOUS MODE”.
1 to 5.
11/33

13. Click “FINISH” button. That means the initial setting is completed.
12/33

14. Programming Software is opened.
15. Click “Setting” on the menu bar and select “Paging Priority Setting”.
13/33

16. The following window opens.
14/33

15/33
17. Assign priority level to channels.
Ch.1 >> PRIORITY 1
Ch.2 >> PRIORITY 2
Ch.7 >> PRIORITY 2
18. Setting of Assignment for ZM-9013 and ZM-9012s.
Click “Setting” on the menu bar and select “Remote Setting Wizard”.

19. Remote Controller Setting Wizard is opened. Just click “NEXT” button.
0. Setting of the first ZM-9013[0]. Here, we assign a function to each button.
2
16/33

21. Button #01 is used as switch of input 3 (Microphone 3).
Assign “CHANGE CROSS POINT” function to #01 and click the point circled in red.
22. Check the boxes as follows and click “OK”.
*INPUT Ch.1, 2 and 7 have priority over the other inputs. Their cross points are set by “Paging
Setting”.
17/33

23. As well as #01 button, assign “CHANGE CROSS POINT” function to #02 - #05 and check
[Button #02]
the boxes as follows.
[Button #03]
18/33

[Button #04]
[Button #05]
19/33

24. No assignment to # 06 - 08. Click “NEXT”.
25. Setting of the first ZM-9012[1].
20/33