ToBattery LFP4830BP User manual

Thank you for purchasing the ToBattery LFP4830BP LiFePO4 Battery
Introduction
LiFePO4 chemistry is an evolution in rechargeable battery technology. It is safer, non-toxic, higher
performing, and longer lasting compared to lead-acid batteries. ToBattery provides the highest
quality LiFePO4 battery from our ISO9001 certified production facility that guarantees maximum
performance. Please carefully review the information below as they are vital to the safety and
performance of the battery.
Typical Applications
- Energy Storage, Electronics, Ham Radio, LED Lights, E-Bikes, E-Scooters, etc.
Contents
1 - ToBattery LFP4830BP LiFePO4 Battery
1 - User Manual
1 - Compatible Charger with 2A & 5A output (optional)
Specifications (summary)
Dimensions ( LxWxH)
11.5x7x6.5 in(290x180x170mm)
Weight
28 lbs. (12.7 kg.)
Battery nominal voltage and capacity
48V, 30Ah
Charging Voltage
58.4V
Charging Current
<10A
Open Circuit Voltage Range
45-55VDC
Maximum Continuous Discharge Current
30A
Maximum Peak Pulse Current
60A (30 sec)
Operating Temperature
- 10°C to 60°C
Protection: PCM/BMS
Overcharge, overdischarge, overcurrent,
temperature, balancing
Terminal / connector type
M8
For the full specification with update , please visit www. tobattery .com
Caution
●Do not disassemble.
●Do not short circuit positive and negative terminals.
●Use only LiFePO4 compatible chargers. Do not use Lead Acid battery chargers
●Do not submerge in water, the seal on the battery is not intended to withstand water pressure
●Do not throw in fire or dispose of improperly. Recycle the battery at a facility that accepts lithium
battery
Last Revised 01/01/2020
Instructions for Use
Charging
1. Only use 58.4V, LiFePO4 compatible chargers to charge the battery. The charging current
should be 2A~10A. If you need a charger, please contact us.
2. Fully charge the battery before first use. This depends on the output of the charger but is
typically between 3-5 hours.
3. If your battery came with a To battery charger, the red LED light means the battery is under
constant current (CC) charging and green LED means constant voltage (CV) charging.
Always charge for at least 5 hours to ensure full capacity.
4. LiFePO4 does not suffer “memory effect” so please keep the battery fully charged for daily
use. Cell balancing only occurs when the battery is fully charged (top-end balancing).
5. Do not charge the battery in temperatures below 0°C. This can cause damage to the cells.
Discharging
1. Make sure your load accepts 48V nominal voltage.
2. Ensure the connection between the battery and the load can handle the current draw.
Please consult references for the appropriate wire type.
3. The maximum continuous discharge current is 30A.
4. The battery outputs a steady voltage around 51.2V until very little capacity remain, do NOT
rely on voltage as an indicator of remaining capacity.
Series and Parallel Connection
We do not recommend using our LiFePO4 batteries in series or parallel connection if a single battery
of equivalent size can be used instead. The PCM/BMS built into each battery is intended only for
operation with a single battery and we do not guarantee the operability of multiple batteries in series
or parallel configuration. Please take the information below into consideration if you must use a
series or parallel configuration.
Series: This battery will not operate in series configuration. Please do not use the battery in
series.
Parallel: Only connect batteries with equal state of charge in parallel. Also, measure the
internal resistance of each battery and only use batteries with closely matched internal
resistance. It is highly recommended that resistors be used to achieve equal internal
resistance among multiple batteries. It is also highly recommended to add fuse(s) to the
circuit for safety reasons.
Please keep in mind a series or parallel connection can fail with a number of consequences, from
early cut off to possibly a fire. Always exercise caution and observe closely at all times. The
customer assumes all responsibility in the event of a series or parallel connection or connections.
Maintenance and Storage
The battery requires no manual maintenance due to the included PCM/BMS. However, please
follow the below guideline for best life cycle.
1. Even though the LiFePO4 chemistry is relatively stable, protect the battery from shocks and
drops to prevent internal short circuit.
2. For long term storage, fully charge the battery and then discharge to 50% of the full capacity.
Do NOT leave the battery unattended for more than 6 months.
3. For the best life cycle, avoid using the battery in extreme temperatures and avoid highly
variable pulsing loads.

Troubleshooting
Since the battery can be used in many different configurations and equipment, we cannot
provide a general troubleshooting guide. Please contact us so a technician can provide
you with individualized support. Because the battery is not maintainable, you cannot
disassemble the battery at any time. Once the battery swells and smokes, stop using it
immediately and move it to a safe place to prevent possible fires and explosions that
could cause injury or death. property loss.
Contact Us
Mail: ToBattery
1289 Fordham Blvd. Suite 116
Chapel Hill, NC 27514
E-mail: [e-mail]
Phone: [phone]
Warranty
Please see the included warranty pamphlet for warranty information. You can also check
www.tobattery.com for more information.
LFP4830BP
LiFePO4 Battery
User Manual