TOCA Touch Trainer Programming manual

1
TOCA MAINTENANCE & TROUBLESHOOTING MANUAL
Attention: Do not open the Main Body Cover on the TOCA Touch
Trainer. Opening the Main Body Cover will void your warranty. If you
have an issue with your TOCA Product, email support at
[email protected] or call 844.444.TOCA.
Performing regular maintenance on your TOCA Touch Trainer will help
prolong the life of the machine and ensure each training session runs
smoothly. This manual is broken down into six sections: Launch Wheels,
TOCA Balls, Solenoid, Motors, Hoppers, and Machine Storage. Each
section includes maintenance and troubleshooting sub-sections.
Launch WHEELS
Maintenance
Wheel Inspection - A visual inspection of the wheels helps to determine
which corrective action is needed.
New Launch Wheels
There will be minor wear
due to quality testing
before the Touch Trainer
arrives.
Proper Wear
Wear is visible on the
wheels as expected, but
note there is no flaking
of the wheels.
Need Replacing
The shape of the rubber
on the wheels is visibly
modified, and flaking
has begun to occur.
These wheels will not
deliver the ball with
consistency and need to
be replaced.
Troubleshooting
If the machine is not shooting properly:
Clean the wheels using a damp, lint-free
towel, and then dry the wheels off.

2
If there is debris on the Launch Wheel Hubs,
clean it out using a dry, lint-free towel.
If the Launch Wheels show signs of rubber
flaking, take a picture and contact Customer
Support at 844.444.TOCA or
[email protected], as Launch Wheel
replacement may be necessary.
If the Launch Wheels are making unusual
vibrating sounds, please call Customer
Support as they may need to be replaced.
TOCA BALLS
Maintenance
Proper Inflation - Before each session, ensure the TOCA Balls are
inflated. Use your ball pressure gauge to inflate the TOCA Balls to 8
PSI for optimal performance.
Cleaning - before each session, wipe off scuffed, sticky or tacky feeling
balls using a damp, lint-free towel. Then, dry balls prior to use.

3
Troubleshooting
If you experience any of the below issues, check the ball pressure and
clean the balls:
•Inconsistent ball delivery
•Irregular rolling or bouncing
•Balls jamming in the motor bracket
If you experience any of the below issues, it might be time to order new balls:
•Balls have a non-spherical shape
•Balls won’t hold pressure any
more
•Ball bladder is punctured
SOLENOID
Maintenance
Push Test - once a month, inspect the solenoid to ensure it can be
pressed in and rotated freely without being impeded.

4
Troubleshooting
If you experience any of the below issues, purchase a can of
WD-40 Dry Lubrication and apply one small, quick spray to the
solenoid as shown above:
•Solenoid resists being manually pushed in
•Solenoid stops clicking when operating the machine
•Machine continually shoots two balls at once
If, after applying WD-40 Dry, the solenoid still won’t work, please call
Customer Support as a solenoid replacement may be necessary.
MOTORS
Maintenance
Debris Cleaning - vacuum any debris from the machine and the
training surface. Debris on the machine or training surface can get
stuck in the motors and obstruct proper delivery.
Troubleshooting
Motor issues are typically due to a lack of maintenance on the wheels.
If you experience any of the below issues, perform debris cleaning as
detailed above. If that doesn’t remedy the problem, please call
technical support as a motor replacement may be necessary:
•Excessive noise from the wheels or motors
•Slow firing of balls

5
SPIRAL HOPPERS
Maintenance
Inspection - performed regularly, confirm:
•Hoppers are correctly installed and aligned
•There are no loose fasteners, and that all screws are holding Hoppers
in place
~Loose connections of the hoppers can cause ball jams and delayed delivery.
Cleaning- Regularly clean the Spiral Hoppers using a damp, lint-free
towel. Dry the Hoppers before use.

6
MACHINE STORAGE
Store your TOCA Touch Trainer in a cool, dry place. Avoid hot and
humid storage locations.
When transporting the machine:
1. Ensure the Touch Trainer is turned off.
Machine is On Machine is Off
2. Unplug the power cable.

7
3. Remove the hoppers.
4. The machine can now be wheeled around.

8
If you must lift the Touch Trainer, hold the machine with one hand on
the handle, and one hand on the base plate. Do not grab the wheels.