ItsaGoal 3M' X 2M' FUTSAL GOAL Install guide

4
4
2
2
2
8
12
x
x
x
x
x
x
x
CORNER BRACKET 4 HOLES
SPIGOT
BLANKING CAP
MULTI-SURFACE ANCHOR
GROUND PEG
STANCHION ELBOW
SMALL QUICK RELEASE BUTTON
LARGE QUICK RELEASE BUTTON
A
B
C
D
E
F
H
I
COMPONENTS
4
x
NET TIE
J38
x
LOWER BACK STANCHION
CONNECTOR
G2
x
1
x
GOAL NET 8' x 6'
23
x
ARROW HEAD NET FIXING
with attached LOCKING PIN
K
NET
2
x
CORNER BRACKET
UPRIGHT 8 HOLES
X
E
E
X
A
A
X
A
A
PLEASE NOTE :
THE NET TIES
CAN BE USED TO
TIE THE NETS TIGHTLY
INTO THE CORNERS
FOR A BETTER FIT.
TEL: [phone]
CARE & MAINTENANCE - see separate sheet supplied
or visit www.itsagoal.net for additional copies. Our goalpost if used
correctly will last many years. We do also offer a full spare part service
and if your goals need refurbishment this can be arranged
GOAL POSTS MUST BE ANCHORED AT ALL TIMES
Optional longer pegs are available for use on sandy ground. On grass, a
risk assessment of soil and weather conditions suitability should be carried
out when anchors or counter weights are to be used.
Extra anchors are available TEL: [phone]
OPTIONAL - STANCHION TIES
See how to fit the net overleaf
J
JS
To register for your guarantee visit www.itsagoal.net
scroll to the bottom of the page and click on the link ‘Guarantee’
and follow the instructions. Thank you.
REGISTER YOUR GUARANTEE
Guarantee
GOAL POSTS MUST BE ANCHORED AT ALL TIMES
Optional longer pegs are available for use on sandy ground. On grass, a
risk assessment of soil and weather conditions suitability should be
carried out when anchors or counter weights are to be used.
Extra anchors are available TEL: [phone]
WORLDWIDE © COPYRIGHT 2001 ITSA GOAL POSTS LTD, ALL RIGHTS RESERVED A REGISTERED DESIGN
WE RESERVE THE RIGHTS TO AMEND THE SPECIFICATIONS OF OUR SOCCER PRODUCTS IN THE INTEREST
OF CONTINUED DEVELOPMENT. YOUR PRODUCT THEREFORE MAY DIFFER LIGHTLY TO THOSE ILLUSTRATED. E&OE
Insert net hooks in holes on
crossbar/uprights and insert pins to lock
Locking Pin
Arrowhead net fixing
DO NOT THROW THE
LOCKING PINS AWAY
Note : Make sure part C, blanking Cap
is inserted in the corner bracket X with
the 8 holes. This part may already be
inserted.
X
C
H
IF GOALS HAVE INTENSIVE USE ADD
THE ADDITIONAL NET TIES TO THE
GROUND BASE FRAME
FITTING
INSTRUCTION
3M' X 2M' FUTSAL GOAL One section crossbar.
68mm
68mm
68mm
68mm
40mm
40mm
2
2
2
2
1
1
x
x
x
x
x
x
CROSSBAR SECTION
2970mm LONG - 68mm Diameter
BACKBAR SECTION
2970mm LONG - 68mm Diameter
SIDEBAR SECTION
1450mm LONG - 68mm Diameter
UPRIGHT SECTION
1886mm LONG - 68mm Diameter
TOP STANCHION TUBE
400mm LONG - 40mm Diameter
BACK STANCHION TUBE
2065mm LONG - 40mm Diameter
L
M
N
O
P
Q
POST SECTIONS

K
STEP BY STEP ASSEMBLY
STEP 1 Lay out POSTS and
Components shown on page 1
STEP 2
Insert Blanking Cap part C and
insert Large Quick Release Button H (x2)
into Corner Bracket X.(NOTE: CornerBracket X
is different from Corner Bracket A. Corner
Bracket X is to be fitted into the upright posts
and has 8 holes.
STEP 3
Insert Small Quick Release Black Button I
into the Spigot B. Insert Spigot B and
insert H (x2) into Corner Bracket A.
(NOTE: Corner Bracket A has 4 holes)
STEP 5
Insert Corner Brackets X into the
upright posts O (uprights have logos on the side)
STEP 6
Insert Corner Brackets A into
each end of the crossbar L
STEP 7
Insert Corner Brackets A into
each end of the Backbar M
STEP 8
Attach Side bars N to
the ground back bar by slotting
into the corners brackets
STEP 9
Attach Upright O to
the Side bars N
STEP 10
Attach Crossbar L
to uprights O
STEP 4
Insert Arrow Head Net Fixings K
into Upright Posts and Crossbar.
DO NOT THROW AWAY
LOCKING PINS
CROSSBAR &
BACKBAR 2422 mm
SIDEBARS
1360 mm LONG
UPRIGHTS
1726 mm
TOP
STANCHION
400 mm
BACK
STANCHION
1896 mm
LM
N
O
P
Q
X
C
H
C O R N E R
BRACKET
H
A
C O R N E R
BRACKET
SPIGOT B
I
L
O
XAA
L
M
G
STEP 11
Join top tubes P to elbows F
and back tubes Q and connect
to the goalpost.
STEP 12
Attach Ground Anchors
see details of use overleaf..
STEP 13
Attach The Net to the
Net Fixings. Start with
each corner
TIE A CORD
BETWEEN THE
TOP SUPPORT TUBES TO
SUPPORT THE ROOF OF THE
NET (THIS CAN BE LEFT TIED
IN POSITION WHEN DISMANTLED)
The goal net can
be left attached to the
pre-assembled goal post
side frames. After games
detach crossbar and back bar
for storage. We advise fitting the
optional net ties to the side frames and stanchions.
ASSEMBLY & DISASSEMBLY
FASTER
MATCH DAY
FOR EASIER ASSEMBLY Use a rubber mallet and also spray furniture polish inside posts. Do not use a metal hammer. Do not apply grease or vaseline.
ANCHORING YOUR GOAL ON GRASS - POSITION YOUR GOAL ON A LEVEL PLAYING SURFACE.
PLACE THE MULTI-SURFACE ANCHOR OVER EACH SIDE OF THE GROUND FRAME (POSITIONS
SHOWN) HAMMER THE PEGS DOWN UNDER THE FRAME INTO THE GRASS. ADDITIONAL
ANCHORS OR LARGER PEGS CAN BE PURCHASED FOR USE ON SOFT GROUND OR SAND. THESE
ANCHORS CAN BE USED FOR HARD SURFACES, SUCH AS TARMAC BY USING BOLTS THROUGH
THE MULTI SURFACE ANCHORS INTO CONCRETE PADS. COUNTER BALANCE WEIGHTS CAN ALSO
BE USED (SUPPLIED SEPARATELY). CHAINS ARE AVAILABLE SEPARATELY THAT CAN BE USED TO
SECURE GOALS TO SEPARATE ANCHOR POINTS.
PEG
REMOVAL
a
b
a
b
OPTIONAL - Net ties are ideal to fit nets tightly to the side ground frames and
stanchions. This is ideally when nets are left attached to the fully assembled side
frames.
WORLDWIDE © COPYRIGHT 2001 ITSA GOAL POSTS LTS, ALL RIGHTS RESERVED A REGISTERED DESIGN
P
F
Q
J

STEP BY STEP ASSEMBLY
STEP 1
Lay out all Posts & components
WORLDWIDE © COPYRIGHT 2016 ITSA GOAL POSTS LTD, ALL RIGHTS RESERVED A REGISTERED DESIGN
UPRIGHT
SECTION
1886mm
P
Q
O
N
L
M
CROSSBAR SECTION
BACKBAR
SECTION
2970mm
SIDEBAR
SECTION
1450mm
TOP
STANCHION
TUBE
400mm
BACK STANCHION TUBE
2065mm
K
STEP 2
Insert Blanking Cap part C and
insert Large Quick Release Button H (x2)
into Corner Bracket X.(NOTE: CornerBracket X
is different from Corner Bracket A. Corner
Bracket X is to be fitted into the upright posts
and has 8 holes.
STEP 3
Insert Small Quick Release Black Button I
into the Spigot B. Insert Spigot B and
insert H (x2) into Corner Bracket A.
(NOTE: Corner Bracket A has 4 holes)
STEP 4
Insert Arrow Head Net Fixings K
into Upright Posts and Crossbar.
DO NOT THROW AWAY
LOCKING PINS
STEP 5
Insert Ground Frame net Fixings NH
into Back bar and Side bar. see details
about removing burrs overleaf.
DO NOT THROW AWAY
LOCKING PINS
AX
C
H
C O R N E R
BRACKET
H
A
C O R N E R
BRACKET
SPIGOT B
I
NH
FOR EASIER ASSEMBLY Use a rubber mallet and also spray furniture polish inside posts. Do not use a metal hammer. Do not apply grease or vaseline.
STEP 6
Insert Corner Brackets AX into the
upright posts O (uprights have logos on the side)
STEP 7
Insert Corner Brackets A into
each end of the crossbar L
STEP 8
Fit G and insert Corner Brackets
A into each end of the Backbar M
STEP 9
Attach Side bars N to
the ground back bar by slotting
into the corners brackets
STEP 10
Attach Upright O to
the Side bars N
STEP 11
Attach Crossbar L
to uprights O
L
O
AX AA
L
M
G
STEP 12
Join top tubes P to elbows F
and back tubes Q and connect
to the goalpost.
STEP 13
Attach Ground Anchors
see details of use overleaf.
P
F
Q
STEP 14
Attach The Net to the
Net Fixings. Start with
each corner
TIE A CORD
BETWEEN THE
TOP SUPPORT TUBES TO
SUPPORT THE ROOF OF THE
NET (THIS CAN BE LEFT TIED
IN POSITION WHEN DISMANTLED)
The goal net can
be left attached to the
pre-assembled goal post
side frames. After games
detach crossbar and back bar
for storage. We advise fitting the
optional net ties to the side frames and stanchions.
ASSEMBLY & DISASSEMBLY
FASTER
MATCH DAY
ANCHORING YOUR GOAL ON GRASS - POSITION YOUR GOAL ON A LEVEL PLAYING SURFACE.
PLACE THE MULTI-SURFACE ANCHOR OVER EACH SIDE OF THE GROUND FRAME (POSITIONS
SHOWN) HAMMER THE PEGS DOWN UNDER THE FRAME INTO THE GRASS. ADDITIONAL
ANCHORS OR LARGER PEGS CAN BE PURCHASED FOR USE ON SOFT GROUND OR SAND. THESE
ANCHORS CAN BE USED FOR HARD SURFACES, SUCH AS TARMAC BY USING BOLTS THROUGH
THE MULTI SURFACE ANCHORS INTO CONCRETE PADS. COUNTER BALANCE WEIGHTS CAN ALSO
BE USED (SUPPLIED SEPARATELY). CHAINS ARE AVAILABLE SEPARATELY THAT CAN BE USED TO
SECURE GOALS TO SEPARATE ANCHOR POINTS.
PEG
REMOVAL
a
b
a
b
OPTIONAL - Net ties are ideal to fit nets tightly to the side ground frames and
stanchions. This is ideally when nets are left attached to the fully assembled side
frames.
NH
OPTIONAL TIES
WORLDWIDE © COPYRIGHT 2001 ITSA GOAL POSTS LTS, ALL RIGHTS RESERVED A REGISTERED DESIGN

CORNER BRACKETS
At the end of the season nets can be tied into a bundle and placed into a
pillow case (not to damage washing machine) and washed at 40 C0 with
normal washing powder. The ground frame can be washed with hot soapy
water. Any scuff marks on posts can be rubbed off with a light abrasive
scouring pad.
WARNING: Check the position of any underground services before using the
ground anchors and pegs. We take no responsibility for any damage or
injury caused in this manner.
NEVER use the goals without the ground anchor system. In severe weather
or windy conditions it is advisable to take your goal down as damage is not
covered by the guarantee in such circumstances. If you find the nets are
worn along the floor it may be rodents, by spreading pepper along the base
frame rodents will be deterred. It is advisable in any contact sport to take
out the relevant insurance's to cover against injury both from taking part,
equipment and other unforeseeable circumstances. Crossbars will not be
replaced within the guarantee period if broken by swinging or climbing or
any other misuse.
DO NOT try to glue any damaged fixings. Plastic materials in this product
vary and this may cause the plastic to break. Always replace any damaged
components.
SQUARE MESH Net is cut to shape. Simply throw over the frame and fit
each end onto top stanchion by securing on each corner of crossbar.
NOTE: If your net does not fit the first time, you may be fitting it to the
goal frame upside down i.e. that is to say the net from the crossbar to
the floor (a) is longer than the length of the net to the bottom of the
upright.(b)
a
b
a
b
We advise adult supervision during assembly and use. Observe and follow
warning labels attached to goal. Do not use any components, nets or parts
if they are damaged or broken. Spare parts and replacement nets are
readily available. If others are to install your goal you should show them
how to erect and dismantle the goal and hand them a copy of the fitting
instruction. If you lose your instructions copies can be attained from our
company website. To avoid damage when dismantling the goal follow
these guidelines: it is advisable in extreme windy conditions to dismantle
the goal and store away. Do not drop any heavy objects on ends of tubes.
When dismantling the goal ensure that all fittings are packed away and
that non are left on the playing surface. Warning goals must never be left
up or used unless they are properly fitted with ground anchors with net
attached and securely pegged down.
Do not use the goal in sub zero temperatures. warning labels should be
replaced when worn and we recommend replacing them every two years -
spare labels available. damaged components requested under guarantee
must be returned for inspection. Failure to follow the warnings, fitting
instructions contained in this document, may invalidate your guarantee.
The company , its agents and representatives do not accept any product
liability if used outside the EU. Use of the product in other countries outside
the EU including the USA is not covered and appropriate insurance should
be taken out by the user to cover for any eventuality. We reserve the rights
to amend the specifications of our soccer products in the interest of
continued development. Your product therefore may differ slightly to those
illustrated. Not suitable for children under 36 months until assembled due
to small parts.
TEL: [phone]
SPARE PARTS
NET TIES
!
1
TEETH
3
2
NET CORD
4
6
7
8
Ensure the teeth of the
Net tie are facing you
(see step 1).
Loop the Net Tie around
the Net Cord and slide
the end into the
horizontal slot and pull
tight onto Net Cord (see
step 1- 2).
The vertical slot of the
Net Tie is used to
secure the net to the
post. Loop the Net Tie
around the post and
insert through
vertical slot and twist to
lock. (steps 3 - 5).
Any excess Net Tie can
looped back into the
vertical slot. This will
also secure the net tie in
a fixed position (steps 6
- 8). If Net Ties are to be
removed after use then
do not loop back into
vertical slot.
5
POST SECTION
PULL
TIGHT
WORLDWIDE © COPYRIGHT 2001 ITSA GOAL, ALL RIGHTS RESERVED A REGISTERED DESIGN
WE RESERVE THE RIGHTS TO AMEND THE SPECIFICATIONS OF OUR SOCCER PRODUCTS IN THE INTEREST OF CONTINUED DEVELOPMENT. YOUR PRODUCT THEREFORE MAY DIFFER LIGHTLY TO THOSE ILLUSTRATED. E&OE
Ensure locking pin
Is inserted Fully in
the posts
DO NOT THROW THE PINS AWAY
3
Push locking pin
Down centre of
Arrow Head
2
Insert Arrow Head
into Holes on
posts
1
Push and Lock the spig-
ots to two of the four
Corner Brackets.
Push and Lock the Blanking
Caps to the two remaining
Corner Brackets. (already
inserted)
Push and Lock the Large
Quick Release Buttons into
the ends of the Corner
Brackets.
Push and Lock the Small
Quick Release Buttons into
the ends of the Spigots.
NOTE : All plastic extrusions vary and therefore some tubes may be looser
or tighter to connector fittings. If you want to increase the diameter of the
fitting just wrap masking tape around the part that fits into the tube, twist
as you insert the fitting and it will grab to the tube tight ...you can make
tighter fits by adding more tape.
To register for your guarantee visit www.itsagoal.net
scroll to the bottom of the page and click on the link ‘Guarantee’
and follow the instructions. Thank you.
REGISTER YOUR GUARANTEE
Guarantee