TOHATSU MD 30B2 User manual

MANUAL
OWNER’S
OB No.003-11075-E
30B2
40B2
50B2
75C2
90C2
115A2
MD
MD30B2-115A2_EN.book Page 1 Wednesday, December 12, 2012 10:43 AM

ENOM00001-0
READ THIS MANUAL BEFORE USING THE OUTBOARD MOTOR. FAILURE TO FOLLOW THE
INSTRUCTIONS AND SAFETY PRECAUTIONS IN THIS MANUAL CAN RESULT IN SERIOUS
INJURY OR DEATH. KEEP THIS MANUAL IN A SAFE LOCATION FOR FUTURE REFERENCE.
Copyright © 2009-2012 Tohatsu Corporation. All rights reserved. No part of this manual may be reproduced
or transmitted in any from or by any means without the express written permission of Tohatsu Corporation.
MD30B2-115A2_EN.book Page 2 Wednesday, December 12, 2012 10:43 AM

3
YOUR TOHATSU OUTBOARD MOTOR
ENOM00002-0
OWNER REGISTRATION AND IDENTIFICATION
Upon purchasing this product, be sure that the WARRANTY CARD is correctly and com-
pletely filled out and mailed to the addressee noted there on. This WARRANTY CARD
identifies you as the legal owner of the product and serves as your warranty registration.
TO THE EXTENT PERMITTED BY APPLICABLE LAW, YOUR OUTBOARD MOTOR WILL
NOT BE COVERED BY THE APPLICABLE LIMITED WARRANTY, IF THIS PROCEDURE IS
NOT FOLLOWED.
ENOM00003-0
PRE-DELIVERY CHECK
Be sure that the product has been checked by an authorized TOHATSU dealer before you
take delivery.
ENOM00004-0
Limited Warranty
Please refer to the TOHATSU outboard motor Limited warranty provided to you with this
product, the terms and conditions of which, as amended from time to time, are incorpo-
rated by reference into the manual.
MD30B2-115A2_EN.book Page 3 Wednesday, December 12, 2012 10:43 AM

4
ENOM00005-0
Serial Number
In the space below, please record the outboard motor’s serial number (indicated both on
the lower motor cover and on the cylinder block). The serial number will be needed in the
event of theft or to quickly identifying the outboard motor type.
Serial Number:
ENOM00006-0
To You, Our Customer
Thank you for selecting a TOHATSU outboard motor. You are now the proud owner of an
excellent outboard motor that will service you for many years to come.
This manual should be read in its entirety and the inspection and maintenance procedures
described later in this manual should be followed carefully. Should a problem arise with the
outboard motor, please follow the troubleshooting procedures listed at the end of this
manual. If the problem persists, contact an authorized TOHATSU service shop or dealer.
We hope you will enjoy your outboard motor and wish you good luck in your boating
adventures.
TOHATSU CORPORATION
MD30B2-115A2_EN.book Page 4 Wednesday, December 12, 2012 10:43 AM

GENERAL SAFETY INFORMATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
1. SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
2. NAMES OF PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
3. LOCATION OF WARNING LABELS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
4. INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
1. Mounting the outboard motor on boat . . . . . . . . . . . . . . . . . . . . . . . . . . .24
2. Propeller selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
3. Installing the remote control devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
4. Installing the meters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
5. Installing the drag link assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
6. Installing the battery. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
5. PRE-OPERATING PREPARATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
1. Recommended gasoline types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
2. Low permeation fuel hose requirement . . . . . . . . . . . . . . . . . . . . . . . . . . .40
EQUIPPED FOR UNITED STATES AND CANADA MODEL
3. EPA pressurized portable fuel tank requirements . . . . . . . . . . . . . . . . . . .41
EQUIPPED FOR UNITED STATES AND CANADA MODEL
4. Recommended engine oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
5. Altitude adjustment kit requirement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
6. Break-In . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
7. Warning system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
6. ENGINE OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
1. Starting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
2. Warming up the engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
3. Forward and reverse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
4. Shallow water running . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58
5. Stopping the engine. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
6. Trim angle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61
7. Mooring with the engine tilted up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64
7. REMOVING AND CARRYING THE OUTBOARD MOTOR. . . . . . . . . . . . . . 68
1. Removing the outboard motor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68
2. Carrying the outboard motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68
3. Storing the outboard motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69
8. TRAILERING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
9. ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71
1. Remote control lever load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71
2. Trim tab adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71
3. Steering load adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72
4. Throttle grip turning load adjustment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
10. INSPECTION AND MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
1. Daily inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74
2. Periodic inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79
3. Off-season storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .84
CONTENTS
MD30B2-115A2_EN.book Page 5 Wednesday, December 12, 2012 10:43 AM

4. Pre-season check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .86
5. Checking after striking underwater object. . . . . . . . . . . . . . . . . . . . . . . . . 86
6. If the engine becomes submerged in water. . . . . . . . . . . . . . . . . . . . . . . . 87
7. Precautions in cold weather. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
11. TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .88
12. TOOL KIT AND SPARE PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
13. OPTIONAL ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
14. PROPELLER TABLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .95
MD30B2-115A2_EN.book Page 6 Wednesday, December 12, 2012 10:43 AM

7
GENERAL SAFETY INFORMATION
1. SPECIFICATIONS
2. NAMES OF PARTS
3. LOCATION OF WARNING LABELS
4. INSTALLATION
5. PRE-OPERATING PREPARATIONS
6. ENGINE OPERATION
7. REMOVING AND CARRYING THE
OUTBOARD MOTOR
8. TRAILERING
9. ADJUSTMENT
10.INSPECTION AND MAINTENANCE
11.TROUBLESHOOTING
12.TOOL KIT AND SPARE PARTS
13.OPTIONAL ACCESSORIES
14.PROPELLER TABLE
INDEX
MD30B2-115A2_EN.book Page 7 Wednesday, December 12, 2012 10:43 AM

8GENERAL SAFETY INFORMATION
ENOM00007-0
NOTICE: DANGER/WARNING/CAUTION/Note
Before installing, operating or otherwise handling your outboard motor, be sure to thor-
oughly read and understand this Owner’s Manual and carefully follow all of the instruc-
tions. Of particular importance is information preceded by the words “DANGER,”
“WARNING,” “CAUTION,” and “Note.” Always pay special attention to such information to
ensure safe operation of the outboard motor at all times.
ENOW00001-0
Failure to observe will result in severe personal injury or death, and possibly property dam-
age.
ENOW00002-0
Failure to observe could result in severe personal injury or death, or property damage.
ENOW00003-0
Failure to observe could result in personal injury or property damage.
ENON00001-0
Note
This instruction provides special information to facilitate the use or maintenance of the outboard
motor or to clarify important points.
ENOM0008-0
EMERGENCY STOP SWITCH
The Emergency Stop Switch will stall the outboard motor when the stop switch tether is
pulled off. This stop switch tether can be attached to the operator of the outboard motor
to minimize or prevent injuries from the propeller in case the operator falls overboard.
We highly recommend use of the Emergency Stop Switch tether.
ENOW00004-0
Accidental activation of the Emergency Stop Switch (such as the tether being pulled out in
heavy seas) could cause passengers to lose their balance and even fall overboard, or it
could result in loss of power in heavy seas, strong currents, or high winds. Loss of control
while mooring is another potential hazard.
To minimize accidental activation of the Emergency Stop Switch, the 500 mm (20 inch.) stop
switch tether is coiled and can extended to a full 1300 mm (51 inch.).
DANGER
WARNING
CAUTION
WARNING
MD30B2-115A2_EN.book Page 8 Wednesday, December 12, 2012 10:43 AM

GENERAL SAFETY INFORMATION 9
ENOM00009-0
SAFE OPERATION OF BOAT
As the operator/driver of the boat, you are responsible for the safety of those aboard and
those in other boat around yours, and for following local boating regulations. You should
be thoroughly knowledgeable on how to correctly operate the boat, outboard motor, and
accessories. To learn about the correct operation and maintenance of the outboard motor,
please read through this manual carefully.
It is very difficult for a person standing or floating in the water to take evasive action should
he or she see a power boat heading in his/her direction, even at a slow speed. Therefore,
when your boat is in the immediate vicinity of people in the water, the outboard motor
should be shifted to neutral and shut off.
ENOW00005-0
SERIOUS INJURY IS LIKELY IF A PERSON IN THE WATER MAKES CONTACT WITH A MOV-
ING BOAT, GEAR HOUSING, PROPELLER, OR ANY SOLID DEVICE RIGIDLY ATTACHED TO
A BOAT OR GEAR HOUSING.
ENOM00010-0
SERVICING, REPLACEMENT PARTS & LUBRICANTS
We recommend that only an authorized service shop perform service or maintenance on
this outboard motor. Be sure to use genuine parts, genuine lubricants, or recommended
lubricants.
ENOM00011-0
MAINTENANCE
As the owner of this outboard motor, you should be acquainted with correct maintenance
procedures. It is the operator’s responsibility to perform all safety checks and to ensure
that all lubrication and maintenance instructions are complied with for safe operation.
Please comply with all instructions concerning lubrication and maintenance. You should
take the engine to an authorized dealer or service shop for periodic inspection at the pre-
scribed intervals.
Correct periodic maintenance and proper care of this outboard motor will reduce the
chance of problems and limit overall operating expenses.
ENOM00012-0
MOUNTING
Outboard motor mounting must be performed by trained service person(s) using lift or
hoist with sufficient capacity.
WARNING
MD30B2-115A2_EN.book Page 9 Wednesday, December 12, 2012 10:43 AM

10 SPECIFICATIONS
ENOM00601-0
Remark: Specifications subject to change without notice.
*1: The idling speed can be set to any of the three rpm ranges, 700, 800 or 900. (See page 52)
30B2 (Available in specific region), 40B2
Item MODEL 30B2 40B2
EPTO EFTO EFO
Overall Length mm (in) 630 (24.8) 1120 (44.1)
Overall Width mm (in) 345 (13.6) 384 (15.1)
Overall Height S·L·UL mm (in) 1227 (48.3) 1354 (53.3) 1481 (58.3)
Transom Height S·L·UL mm (in) 403 (15.9) 530 (20.9) 657 (25.9)
Weight
Skg(lb)———
L kg (lb) 94.5 (208) 97.5 (215) 89.5 (197)
ULkg(lb)———
Output kW (ps) 22.1 (30) 29.4 (40)
Max. Operating Range rpm 4750–5750
Idle Speed rpm 700/800/900 *1
Engine Type Direct fuel injection
Number of Cylinder 3
Bore × Stroke mm (in) 68 × 64 (2.68 × 2.52)
Piston Displacement mL (Cu in) 697 (42.5)
Exhaust System Through hub exhaust
Emission Controls EC (Electronic Control)
Cooling System Water cooling
Engine Lubrication Oil injection
Starting System Electric starter motor
Ignition System Inductive Ignition
Spark Plug NGK IZFR6Q
Alternator 12 V, 280 W (Max.)
Trim Position 4 6
Engine Oil Genuine Motor Oil or recommended one
Gear Oil Genuine Gear Oil or API GL5, SAE #80 to #90, approx. 500 mL
Fuel Tank Capacity L (US gal) 25 (6.6)
Engine Oil Capacity L (US gal) Approx. 2.0 (0.53)
Gear Reduction Ratio 1.85 (13 : 24)
Fuel Unleaded regular gasoline : Pump posted 87 Octane
(research octane rating of 91)
Emission Control System DFI (Direct Fuel Injection)
Operator Sound Pressure
(ICOMIA 39/94) dB (A) 84.0
Hand Vibration Level
(ICOMIA 38/94) m/sec2 —3.8
MD30B2-115A2_EN.book Page 10 Wednesday, December 12, 2012 10:43 AM

SPECIFICATIONS 11
ENOM00602-0
Remark: Specifications subject to change without notice.
*1: The idling speed can be set to any of the three rpm ranges, 700, 800 or 900. (See page 52)
50B2
Item MODEL 50B2
EPTO EFTO EFO
Overall Length mm (in) 630 (24.8) 1120 (44.1)
Overall Width mm (in) 345 (13.6) 384 (15.1)
Overall Height S·L·UL mm (in) 1227 (48.3) 1354 (53.3) 1481 (58.3)
Transom Height S·L·UL mm (in) 403 (15.9) 530 (20.9) 657 (25.9)
Weight
S kg (lb) 93.5 (206) 96.5 (213) 88.5 (195)
L kg (lb) 94.5 (208) 97.5 (215) 89.5 (197)
UL kg (lb) 97 (214) 100 (220) 92 (203)
Output kW (ps) 29.4 (40) 36.8 (50)
Max. Operating Range rpm 5150–5850
Idle Speed rpm 700/800/900 *1
Engine Type Direct fuel injection
Number of Cylinder 3
Bore × Stroke mm (in) 68 × 64 (2.68 × 2.52)
Piston Displacement mL (Cu in) 697 (42.5)
Exhaust System Through hub exhaust
Emission Controls EC (Electronic Control)
Cooling System Water cooling
Engine Lubrication Oil injection
Starting System Electric starter motor
Ignition System Inductive Ignition
Spark Plug NGK IZFR6Q
Alternator 12 V, 280 W (Max.)
Trim Position 4 6
Engine Oil Genuine Motor Oil or recommended one
Gear Oil Genuine Gear Oil or API GL5, SAE #80 to #90, approx. 500 mL
Fuel Tank Capacity L (US gal) 25 (6.6)
Engine Oil Capacity L (US gal) Approx. 2.0 (0.53)
Gear Reduction Ratio 1.85 (13 : 24)
Fuel Unleaded regular gasoline : Pump posted 87 Octane
(research octane rating of 91)
Emission Control System DFI (Direct Fuel Injection)
Operator Sound Pressure
(ICOMIA 39/94) dB (A) 81.7
Hand Vibration Level
(ICOMIA 38/94) m/sec2 —3.8
MD30B2-115A2_EN.book Page 11 Wednesday, December 12, 2012 10:43 AM

SPECIFICATIONS12
ENOM00603-0
Remark: Specifications subject to change without notice.
*1: The idling speed can be set to any of the three rpm ranges, 700, 800 or 900. (See page 52)
W50B2
Item MODEL W50B2
EPTO EFTO
Overall Length mm (in) 630 (24.8) 1120 (44.1)
Overall Width mm (in) 345 (13.6) 384 (15.1)
Overall Height L·UL mm (in) 1415 (55.7) 1542 (60.7)
Transom Height L·UL mm (in) 550 (21.7) 677 (26.7)
Weight L kg (lb) 100.5 (222) 103.5 (228)
UL kg (lb) 101.5 (224) 104.5 (230)
Output kW (ps) 36.8 (50)
Max. Operating Range rpm 5150–5850
Idle Speed rpm 700/800/900 *1
Engine Type Direct fuel injection
Number of Cylinder 3
Bore × Stroke mm (in) 68 × 64 (2.68 × 2.52)
Piston Displacement mL (Cu in) 697 (42.5)
Exhaust System Through hub exhaust
Emission Controls EC (Electronic Control)
Cooling System Water cooling
Engine Lubrication Oil injection
Starting System Electric starter motor
Ignition System Inductive Ignition
Spark Plug NGK IZFR6Q
Alternator 12 V, 280 W (Max.)
Trim Position 4
Engine Oil Genuine Motor Oil or recommended one
Gear Oil Genuine Gear Oil or API GL5, SAE #80 to #90, approx. 700 mL
Fuel Tank Capacity L (US gal) 25 (6.6)
Engine Oil Capacity L (US gal) Approx. 2.0 (0.53)
Gear Reduction Ratio 1.92 (12 : 23)
Fuel Unleaded regular gasoline : Pump posted 87 Octane
(research octane rating of 91)
Emission Control System DFI (Direct Fuel Injection)
Operator Sound Pressure
(ICOMIA 39/94) dB (A) 84.0
Hand Vibration Level
(ICOMIA 38/94) m/sec2 —3.8
MD30B2-115A2_EN.book Page 12 Wednesday, December 12, 2012 10:43 AM

SPECIFICATIONS 13
ENOM00604-0
Remark: Specifications subject to change without notice.
*1: The idling speed can be set to any of the three rpm ranges, 700, 800 or 900. (See page 52)
75C2, 90C2
Item MODEL 75C2 90C2
EPTO
Overall Length mm (in) 810 (31.9)
Overall Width mm (in) 508 (20.0)
Overall Height L·UL mm (in) 1540 (60.6) 1667 (65.6)
Transom Height L·UL mm (in) 517 (20.4) 644 (25.4)
Weight L·UL kg (lb) 152 (335) 155 (342)
Output kW (ps) 55.2 (75) 66.2 (90)
Max. Operating Range rpm 5150–5850
Idle Speed rpm 700/800/900 *1
Engine Type Direct fuel injection
Number of Cylinder 3
Bore × Stroke mm (in) 86 × 72.7 (3.39 × 2.86)
Piston Displacement mL (Cu in) 1267
Exhaust System Through hub exhaust
Emission Controls EC (Electronic Control)
Cooling System Water cooling
Engine Lubrication Oil injection
Starting System Electric starter motor
Ignition System Inductive Ignition
Spark Plug NGK IZFR6Q
Alternator 12 V, 490 W (Max.)
Trim Position 2
Engine Oil Genuine Motor Oil or recommended one
Gear Oil Genuine Gear Oil or API GL5, SAE #80 to #90, approx. 900 mL
Fuel Tank Capacity L (US gal) —
Engine Oil Capacity L (US gal) Approx. 4 (1.06)
Gear Reduction Ratio 2.33 (12:28)
Fuel Unleaded regular gasoline : Pump posted 87 Octane
(research octane rating of 91)
Emission Control System DFI (Direct Fuel Injection)
Operator Sound Pressure
(ICOMIA 39/94) dB (A) 81.7
Hand Vibration Level
(ICOMIA 38/94) m/sec2 —
MD30B2-115A2_EN.book Page 13 Wednesday, December 12, 2012 10:43 AM

SPECIFICATIONS14
ENOM00605-0
Remark: Specifications subject to change without notice.
*1: The idling speed can be set to any of the three rpm ranges, 700, 800 or 900. (See page 52)
115A2
Item MODEL 115A2
EPTO
Overall Length mm (in) 800 (31.5)
Overall Width mm (in) 495 (19.5)
Overall Height L·UL mm (in) 1640 (64.6) 1767 (69.6)
Transom Height L·UL mm (in) 517 (20.4) 644 (25.4)
Weight L·UL kg (lb) 178 (392) 181 (399)
Output kW (ps) 84.6 (115)
Max. Operating Range rpm 5150–5850
Idle Speed rpm 700/800/900 *1
Engine Type Direct fuel injection
Number of Cylinder 4
Bore × Stroke mm (in) 88 × 72.7 (3.46 × 2.86)
Piston Displacement mL (Cu in) 1768 (107.9)
Exhaust System Through hub exhaust
Emission Controls EC (Electronic Control)
Cooling System Water cooling
Engine Lubrication Oil injection
Starting System Electric starter motor
Ignition System Inductive Ignition
Spark Plug NGK IZFR5J
Alternator 12 V, 490 W (Max.)
Trim Position 2
Engine Oil Genuine Motor Oil or recommended one
Gear Oil Genuine Gear Oil or API GL5, SAE #80 to #90, approx. 900 mL
Fuel Tank Capacity L (US gal) —
Engine Oil Capacity L (US gal) Approx. 6.7 (1.77)
Gear Reduction Ratio 2.0 (13:26)
Fuel Unleaded regular gasoline : Pump posted 87 Octane
(research octane rating of 91)
Emission Control System DFI (Direct Fuel Injection)
Operator Sound Pressure
(ICOMIA 39/94) dB (A) 83.3
Hand Vibration Level
(ICOMIA 38/94) m/sec2 —
MD30B2-115A2_EN.book Page 14 Wednesday, December 12, 2012 10:43 AM

15
NAMES OF PARTS
ENOM00606-0
EFO/40B2, 50B2
1
2
3
8
9
10
11
13
14
15
17
18
19
20
21
22
12
4
5
6
7
16
ENOF00601-0
1 Tilt Handle
2 Top C owl
3 Hook Lever
4 Water Check Port
5 Reverse Lock Lever
6 Water Plug
7 Anti-ventilation Plate
8 Trim Tab
9 Propeller
10 Oil Plug (lower)
11 Water Inlet
12 Oil Plug (upper)
13 Clamp Bracket
14 Thrust Rod
15 Clamp Screw
16 Throttle Grip
17 Stop Switch
18 Shift Lever
19 Anode
20 Pilot Lamp
21 Main Switch
22 Battery Cords
MD30B2-115A2_EN.book Page 15 Wednesday, December 12, 2012 10:43 AM

NAMES OF PARTS16
ENOM00607-0
EFTO/30B2, 40B2, 50B2, W50B2
1
2
3
8
9
10
10
11
13
14
15
16
17
18
24
22
19
20
23
21
12
4
5
6
6,12
7
[W50]
[W50]
ENOF00602-0
1 Tilt Handle
2 Top C owl
3 Hook Lever
4 Water Check Port
5 Tilt Stopper
6 Water Plug
7 Anti-ventilation Plate
8 Trim Tab
9 Propeller
10 Oil Plug (lower)
11 Water Inlet
12 Oil Plug (upper)
13 Clamp Bracket
14 Thrust Rod
15 Clamp Screw
16 Throttle Grip
17 Shift Lever
18 Stop Switch
19 Pilot Lamp
20 Main Switch
21 Battery Cords
22 Power Trim & Tilt
23 Anode
24 Power Trim & Tilt Switch
MD30B2-115A2_EN.book Page 16 Wednesday, December 12, 2012 10:43 AM

NAMES OF PARTS 17
ENOM00608-0
EPTO/30B2, 40B2, 50B2, W50B2
1
2
3
8
9
10
11
13
14
16
17
18
19
12
4
5
6
7
10
6,12
[W50]
[W50]
15
ENOF00603-0
1 Tilt Handle
2 Top C owl
3 Hook Lever
4 Water Check Port
5 Tilt Stopper
6 Water Plug
7 Anti-ventilation Plate
8 Trim Tab
9 Propeller
10 Oil Plug (lower)
11 Water Inlet
12 Oil Plug (upper)
13 Clamp Bracket
14 Thrust Rod
15 Power Trim & Tilt Switch
16 Fuel Connector
17 Battery Cords
18 Power Trim & Tilt
19 Anode
MD30B2-115A2_EN.book Page 17 Wednesday, December 12, 2012 10:43 AM

NAMES OF PARTS18
ENOM00609-0
EFTO/75C2, 90C2
1
2
3
3
8
5, 9
10 11
13
14
15
16
17
18
19
12
4
6
7
ENOF00604-0
1 Tilt Handle
2 Top C owl
3 Hook Lever
4 Water Check Port
5 Water Plug
6 Anti-ventilation Plate
7 Trim Tab
8 Propeller
9 Oil Plug (upper)
10 Water Inlet
11 Oil Plug (lower)
12 Clamp Bracket
13 Thrust Rod
14 Fuel Nose Nipple
15 Power Trim & Tilt Switch
16 Battery Cords
17 Power Trim & Tilt
18 Anode
19 Flushing Connector Cap
MD30B2-115A2_EN.book Page 18 Wednesday, December 12, 2012 10:43 AM

NAMES OF PARTS 19
ENOM00610-0
ENON00601-0
Note
These parts for model 115A2 are not enclosed in the engine package.
EPTO/115A2
1
2
3
3
8
5, 9
10 11
13
14
15
16
17
18
124
6
7
26
29 28
27
30 31
20
21
22
19 23
25
24
ENOF00605-0
1 Tilt Handle
2 Top C owl
3 Hook Lever
4 Water Check Port
5 Water Plug
6 Anti-ventilation Plate
7 Trim Tab
8 Propeller
9 Oil Plug (upper)
10 Water Inlet
11 Oil Plug (lower)
12 Clamp Bracket
13 Thrust Rod
14 Fuel Nose Nipple
15 Power Trim & Tilt Switch
16 Battery Cords
17 Power Trim & Tilt
18 Anode
19 Remote Control Box
20 Remote Control Lever
21 Power Trim & Tilt Switch
22 Free Accel Lever
23 Main Switch
24 Harness B
25 Stop Switch
26 Fuel Tank
27 Air Vent Screw
28 Fuel Connector
29 Primer Bulb
30 Tachometer
31 Trim Meter
MD30B2-115A2_EN.book Page 19 Wednesday, December 12, 2012 10:43 AM

20 LOCATION OF WARNING LABELS
ENOM00620-0
1. Warning label regarding owner’s man-
ual, top cowl, engine stop switch,
engine oil level and unleaded gasoline.
2. Only for EU remote control model
Warning label regarding installation of
remote control system (See page 27).
3. Only for EU model
Warning label regarding emergency
starting (See page 54).
4. Warning label on position of outboard
motor when setting down.
Locations of warning labels
5
MD 30/40/50
MD 75/90/115
6
3
1
2
4
10
9
11
8
ENOF00606-0
7
ENOF00005-0
ENOF00120-0
ENOF00128-0
MD30B2-115A2_EN.book Page 20 Wednesday, December 12, 2012 10:43 AM