Tomoloo X-Man K1 User manual

X-Man K1 Hoverboard
User Manual • Uživatelský manuál •
Užívateľský manuál • Használati utasítás •
Benutzerhandbuch

2
English
3 –23
Čeština
24 –42
Slovenčina
43 –62
Magyar
63 –82
Deutsch
83 –103

3
Dear customer,
Thank you for purchasing our product. Please read the following instructions carefully
before first use and keep this user manual for future reference. Pay particular attention
to the safety instructions. If you have any questions or comments about the device,
please contact the customer line.
󲐜󲐝󲐞󲐟󲐠www.alza.co.uk/kontakt
✆[phone]
Importer Alza.cz a.s., Jankovcova 1522/53, Holešovice, 170 00 Praha 7, www.alza.cz

4
Attention and Safety Instructions
The operating temperature range of the charger is 32°-1 04°F (0°-40°C)
The operating temperature range of the K1 is 32°-1 04°F(0°-40°C).
Do not ride on icy or slippery surfaces.
Read the user manual before riding.
Store the K1 in a dry, ventilated environment.
When transporting the K1, avoid violent crashes or impact.
When the device displays low battery or no power placed for more than 3 months, the
battery will enter sleep mode and can’t be charged anymore. We suggest to charge the
device each month.
After leaving your device for more than 15 minutes and without any operation, the
device will automatically shut down.
Low Temperature Warning
Low temperature will affect the lubrication of moving parts inside the K1 hoverboard,
increasing internal resistance. At the same time, in low temperatures, the discharge
capacity and the capacity itself of the battery will significantly be decreased. Do not ride
the K1 violently in low temperatures around or below 32° F (0°C).
Safety Instructions
Keep the device away from heat sources, direct sunlight, humidity, and prolonged
exposure to water.
Do not operate the device if it has been exposed to water, moisture, or any other liquids
to prevent against electric shock, explosion and/or injury to yourself and damage to the
device.
Do not use the device if it has been dropped or damaged in any way.
Repairs to electrical equipment should only be performed by a qualified electrician.
Improper repairs may place the user at serious risk.
Do not puncture or harm the exterior surface of the product in any way.
Keep the device free from dust, lint, etc.
Do not use this device for anything other than its intended use or purpose. Doing so
may damage the device.
This product is not a toy. Keep out of reach of children.
Do not expose batteries, battery pack, or batteries installed to excessive heat, such as
direct sunlight, or open flame.

5
About this Manual
PLEASE READ THE USER MANUAL THOROUGHLY. Failure to follow the basic instructions
and safety precautions listed in the user manual may damage your device or cause body
injury.
Thank you for purchasing the TOMOMLOO K1 hoverboard. Please read all instructions
carefully before using and retain this manual for future use and reference.
This manual applies to the TOMOLOO K1 hoverboard.
In order to avoid dangers that caused by collisions, falls, and loss of control, please learn
how to ride safely.
You can learn operating skills by reading the product manual.
This manual includes all operating instructions and precautions, and users must read it
carefully and follow the instructions.
All users are responsible for any consequences caused by violating warning contents or
prompt operations.
Product Introduction
The TOMOLOO K1 is a personal transporter. Our technology and production processes
are developed with strict testing for each TOMOLOO hoverboard. Driving without
following the contents of this manual may lead to damage to your device or may cause
bodily injury.
This manual is designed to give you the information you need for the safe operation and
maintenance of your new K1. Please read it thoroughly before riding your K1.
Package Contains
TOMOLOO K1 Hoverboard
3-pin Charge Cable
Operation Manual
(21.471b/9.74 kg)

6
Features/Parts
1. Fender
2. Left Foot Mat
3. Running Indicator
4. Power/Battery Indicator
5. Right Foot Mat
6. Path Illuminating Lights
7. Side LED Lights
8. Power Button (Located in rear)
9. Charge Port (Located in rear)
10. Solid Tire/Motor

7
Operating Principals
The device uses digital electronic gyroscopes and acceleration sensors to control
balance and motion, depending on the user's centre of gravity. The device also uses a
control system to drive the motors that are located within the wheels. The device has a
built-in inertia dynamic stabilization system that can help assist with balance when
moving forward and backwards, but not while turning.
TIP: To increase your stability, you should keep your body be balanced in order to over-
come the centrifugal force during turns, especially when entering a turn at higher
speeds.
Warning: Any K1 hoverboard that does not work properly can cause you to lose control
and fall. Check the entire device thoroughly before every riding, and do not ride it until
any problems have been corrected.
Specifications
Model
KI
Net Weight
18.3lbs (8.3kg)
Load
44-265 lbs (20-120 kg)
Max Speed
Up to 9 mph (14.4 km/h)
Max Distance Range
Up to 9 miles (14.4 km)
Max Climbing Angle
15°-20°
Minimum Turning Radius
0°
Battery Type
Lithium-ion
Battery Voltage
36V
Battery Capacity
4Ah
Power Requirement
AC 100-24 0V, 50-60 Hz
Wheel Size
6.5 Inches (16.51 cm)
Tire Type
Non-Pneumatic Solid Tires
Bluetooth Range
Up to 33ft
Bluetooth Speaker
V5.0 with stereo sound quality
UL Certification
UL 2272 approved
*The above data is based on laboratory test results, the actual data may be different
according to the weight of users, road conditions, temperature, etc.

8
Controls and Display
Turning Your Device On/Off
Power On: Take your device out of the box and place it flat on a level surface. Press the
power button (located on the rear of your device) once. Check the battery LED indicator
(located in the centre of your device). The battery indicator light should be lit, indicating
the device is powered on.
Power Off: Press the power button once.
Mat Sensor
There are four sensors under the foot mats on your K1 hoverboard. When the user
steps off the mats, it will automatically initiate self-calibration.
When riding the hoverboard, you must ensure you are stepping on the foot mats. Do
not step or stand on any other area of your hoverboard.
Do not put items on the foot mats. Doing so will make the K1 turn on and increase the
probability of collision and cause injury to people, riders, or damage the device.
Battery Indicator
The display board is located in the middle of the K1 hoverboard.
•Green LED light indicates the device is charged above 20 percent.
•Yellow LED light indicates the power is under 20 percent.
•Red LED light indicates the power is down to 10 percent or lower.
When the LED light turns red, please stop riding.
Running Indicator
When the operator triggers the foot mats, the Running Indicator LED will light up, which
means that the system enters the running state.
When the system has an error during operation, the running LED light will turn red (for
more details see Chapter: SAFE RIDING).

9
Bluetooth Speaker
The K1 has powerful built-in wireless speakers so you can play your music while riding.
Pairing the Speaker
Turn on your K1 and the speakers will “DingDong” to announce that it's waiting for a
Bluetooth" connection. This will indicate your K1 speaker is now in pairing mode.
Place the K1 and the Bluetooth" device to which you would like to pair it within the
operating distance. We recommend keeping the two devices no further than 3 feet apart
during pairing.
Ensure Bluetooth" is enabled on your phone or music device. Refer to manufacturer's
instructions for how to enable Bluetooth" on your device.
Once you have activated Bluetooth" on your device, select the option " music " from the
list of available Bluetooth" devices.
If required, enter the PIN code "000000" and confirm the entry.
The K1 will say “Paired” when successfully paired.
Please note, pairing mode on the K1 will last for two minutes. If no devices are paired
after two minutes, the K1 speaker will automatically return to standby mode.
If pairing is unsuccessful, turn off the K1 first and re-pair following the afore mentioned
steps.
If your smart phone is out of range, or the battery is low on your K1, your speaker may
disconnect from your smart device, and the K1 will say “Disconnected”. To reconnect,
follow the after mentioned steps or recharge your hoverboard.
NOTE: Once you have paired the K1 speaker with a device, the speaker will remember
this device and will pair automatically when the device's Bluetooth” is activated and in
range. You do not need to re-pair any previously connected devices.
Your K1 can pair up to two multi-point devices. You can reconnect a previously paired
device without going through the pairing or PIN process on up to two devices.
Listening to Music
Once the K1 speakers are paired to your device, you can stream music wirelessly to
them. Select the track you wish to listen to on your device to listen via the speakers. All
volume and track controls will be made using your music device. Should you encounter
any problems while streaming, please refer to your device's user manual.

10
Smartphone App
Your K1 is an App-enabled hoverboard that works with Apple IOS and Android devices.
Download the free TOMOLOO app in order to access certain features of your K1 such as
headlight colours and skill mode. Using a QR code reader, hold the camera on your
smartphone over the below QR code to download the TOMOLOO app. Feel free to
search “TOMOLOO” in your device app.
Dashboard
Bluetooth- To connect your K1 through Bluetooth on your smartphone, press “Connect”.
If your K1 is already paired, this part of the screen will show “Connected” in blue.
Settings - Press the gear icon to adjust settings.
Speed - The digital speedometer displays your speed in kms per hour.
Battery - The percentage displays the remaining battery life of your K1.
Enjoy - Operation Tips.
Sports - Enter the sports mode.
Change Mode - Change Riding modes: Beginner, Intermediate, Advanced.
Standby - Turn on & turn off the scooter.
Customize Headlights - Change the colours and brightness of your LED Lights.
Friends-This function can help you add your friends who also have "TOMOLOO
hoverboard", and you can review his/her recent games in his/her page.
Home - Back to home page.
Challenge- You can PK your friends who also have "TOMOLOO hoverboard" in this
Mode, which can be set as you like.
More - Display more information.

11
Bluetooth
Press "Bluetooth" to have the App begin scanning for any Tomoloo devices. Your K1
must be powered on and your smart phone's Bluetooth must be enabled. If your
Bluetooth is not enabled on your smart phone, the App will remind you to enable it.
Once scanning is complete, all detected Tomoloo scooters will display in a list. Press the
select button to pair with a scooter and use the PIN "000000". If multiple Tomoloo
scooters appear, continue attempting to pair until your K1 is paired.
Once paired, the dashboard will display "Connected" in blue. You may now begin using
the App with your K1.
Settings
Press the gear icon to change settings for your K1.
•Username - Customize the name for your K1 here. This name change will reflect
in the dashboard and connect pages.
•Password - Customize the password for the K1.
•Switch - Switch between MPH/KMH.
•Speed - Change the speed for the K1.
•Force - Change the Driving Force.
•Sensitivity - Change the Sensitivity for the K1.
Set Dormant Shutdown Time -This setting allows you to set a time for your K1 to
shutdown automatically.
Skill/Safety Modes
Cycle between 3 different skill modes. Each mode has a different top speed and
sensitivity. The mode will only change if you are not using your K1 hoverboard.
•Low Mode - This mode is recommended for first time TOMOLOO hoverboard
users. In this mode, the sensitivity and top speed are very low.
•Normal Mode - This mode is recommended for users that are comfortable using
TOMOLOO hoverboards but are not ready for full speed and extra sensitive
controls. In this mode, the sensitivity and top speed are moderate.
•High Mode - This mode is recommended for everyday TOMOLOO hoverboard
users. In this mode, the sensitivity and top speed are set to the maximum setting.
NOTE: Skill and safety mode must be selected. The TOMOLOO will default to " Normal"
mode if another mode is not selected.

12
Headlights
Press "lights" to set a custom colour and brightness for your K1's Path illumination
Lights. Simply choose your desired colour from the colour wheel. Slide the "Brightness"
bar to adjust brightness. For your convenience, 4 basic colours have also been set as
pre-sets below the brightness bar.
Charging your K1
Ensure that the charging port is clean and dry.
Open the charging port on your K1 hoverboard.
Make sure that there is no dust, debris, or dirt inside the port.
Plug the charger into a grounded wall outlet.
Ensure the light on the charger is GREEN.
Align and connect the 3-pin charging cable into the charging port of the K1.
The charging indicator light on the charger change to Red, indicating that your device is
now being charged.
When the RED indicator light on your charger turns to GREEN, then your device is fully
charged.
A full charge may take up to 3.5 hours.
After fully charging your K1, unplug the charger from your device and from the power
outlet.
Riding your K1
FAILURE TO FOLLOW ANY OF THE FOLLOWING SAFETY PRECAUTIONS MAY LEAD TO
DAMAGE YOUR DEVICE, VOID YOUR MANUFACTURER WARRANTY, LEAD TO PROPERTY
DAMAGE, CAUSE SERIOUS BODILY INJURY, OR MAY LEAD TO DEATH.
Before using your device, be sure to familiarize yourself with the operating procedures.

13
OPERATING YOUR DEVICE
Make sure the device is fully charged before your initial use. For charging instructions,
please follow details under 2.8 CHARGING YOUR K1.
Stand directly behind your device and place one foot on the corresponding foot mat (as
described in the diagram below).
Keep all your weight on your back foot still on the ground, otherwise your device will
begin to move, making it difficult to step on evenly with your other foot. When you are
ready, shift your weight to the foot already placed on the device and step on with your
second foot quickly and evenly (as described in the diagram below).
First, step on one pedal to trigger the footswitch.
Second, step on with your other foot.
NOTE: Stay relaxed and step on quickly, confidently, and evenly. Imagine climbing stairs,
one foot, then the other. Look up once your feet are even.

14
Find your centre of gravity. If your weight is distributed correctly on the foot mats and
your centre of gravity is level, you should be able to stand on your device just as if you
were standing on the ground.
On average, it takes 3-5 minutes just to get comfortable standing on your device and
maintaining proper balance. Having a spotter will help you feel more secure. The K1 is
an incredibly intuitive device; it senses even the slightest bit of motion, so having any
anxiety or reservation about stepping on may cause you to panic and trigger unwanted
movement.
When you first using your device, the fastest way to move on your desired direction is to
focus on that direction. You will notice that just thinking about which way you would like
to go will shift your centre of gravity, and that subtle movement will propel you in that
direction. Your centre of gravity determines which direction you move, accelerate,
decelerate, and come to a complete stop. As described in the diagram below, tilt your
centre of gravity in the direction you wish to move. To turn, focus on the direction you
wish to turn and stay relaxed.
Warning: Do not turn suddenly while driving fast, do not ride sideways or turn on a
slope. The self-balancing sensors may malfunction and risk your safety.
The more comfortable you get on the device, the easier you will manoeuvre. Remember
at higher speeds, it is necessary to shift your weight to overcome the centrifugal force.
For bumps or uneven roads, bend your knees.
Back
Balance
Go Ahead
NOTE: Try staying relaxed and focus on finding your centre of gravity to maintain full
control of your K1 hoverboard.

15
Dismounting your device can be one of the easiest steps, yet when done incorrectly,
may cause you to fall. To properly dismount, from a stopped position, lift one leg up and
set your foot back down on the ground (STEPPING BACK). Then step off completely as
described in the following diagram:
Before you get off, make sure that the hoverboard is stopped, then step off one foot at a
time.
Warning: Make sure to lift your leg completely off the foot mat to clear the device when
stepping back to dismount. Failure to do so may send the K1 into a tailspin.
NOTE: If the K1 is not placed on a level surface, an alarm will sound, and the warning
indicator will light up and prevent the K1 from moving. Place the K1 on a level surface
and try riding it again.
Weight and Speed Limitations
Speed and weight limits are set for your own safety. Please do not exceed the limits
listed here in the manual.
Maximum Weight:
265 lbs
Minimum Weight:
44 lbs
Maximum Speed:
9 mph
Warning: Overweight exertion on the device may increase possibility of injury or
product damage.
NOTE: To prevent injury, when max speed is reached, the K1 will beep to alert the user
and tilt the rider slowly back.

16
Operating Range
Please notice the K1 can travel a distance up to 9 miles on a fully charged battery in ideal
conditions. The following are some of the major factors that will affect the operating
range of your device.
Terrain: A smooth, flat surface will increase your driving distance, while driving uphill, as
well as rough or uneven terrain will reduce your distance significantly.
Weight: The weight of the user can affect driving distance; a lighter user will have further
range than a heavier user.
Ambient temperature: Please ride and store the device under recommended
temperatures, which will increase driving distance: battery life, and overall performance
of your device.
Maintenance: Reasonable battery charging and maintenance will increase the distance.
Overcharging the battery can reduce range.
Speed and Driving Style: Maintaining a moderate speed will increase your distance:
while traveling at high speeds for extended periods, frequent starts, stops, idling, along
with frequent acceleration and deceleration will reduce your overall distance.
Balance and Calibration
If your K1 is unbalanced, vibrating, or not turning properly, you can follow the below
steps to calibrate it.
First, place your K1 on a flat, horizontal surface, such as a floor or a table. The foot mats
should be even with each other and not titled forward or backward. Make sure the
charger is not plug in and the board is turned off.
Press and hold the ON/OFF button for a total 15 seconds. The hoverboard will turn on,
lighting the battery indicator on the board.
Turn the board off and then turn the board back on. Press the power button twice.
Calibration will now be completed.

17
Product Warnings
While riding your K1 hoverboard, if there is a system error or illegal operation
performed with your device, the system cannot enter self-balancing mode, so the device
will prompt the user in a variety of ways.
You will notice the Running Indicator Light will turn RED and you will hear a beep sound
alerting you to take precaution and cease operation.
The following are common occurrences where you will hear the Safety Alerts. These
notices should not be ignored, but appropriate action should be taken to correct any
illegal operation, failure, or errors.
•Prohibited riding surfaces (uneven, too steep, unsafe, etc.)
•When you step on the device, if the platform is tilted more than 10 degrees
forward or backward.
•Battery voltage is too low.
•The device is still charging.
•During operation, the platform self-initiates to tilt due to excess speed.
•Overheating, or motor temperature is too high.
•The device has been rocking back and forth over 30 seconds.
•System enters protection mode; the alarm indicator will light up and buzzer will
alarm (this typically occurs when the battery is about to run out of power).
•If the platform is tilted forward or backward more than 15 degrees, device will
sound “Bibibi” as alarm and can’t ride.
•If any or both tires are blocked, the device will stop after 10 seconds.
•When the battery level has depleted below protection mode, the device engine
will.
•power off after 15 seconds.
•While sustaining a high discharge current during use (such as driving up a steep
slope for a long period of time), the device engine will power off after 15 seconds.
While riding your K1 hoverboard, if there is a system error or illegal operation
performed with your device, the system cannot enter self-balancing mode, so the device
will prompt the user in a variety of ways.

18
Safe Riding
Children, the elderly, and pregnant women should not ride the K1.
Do not ride after drinking or using drugs.
Do not carry items when you are riding the device.
Prior to each use, inspect the K1 and ensure it has been maintained correctly and is
functioning properly.
When riding the K1, please give way to pedestrians.
Please be alert to things in front and far away from you. Keeping good vision will help
you ride the K1 safety.
Make sure your feet are always placed securely on the pads.
The K1 cannot be ridden by two or more people, only one person can operate the K1 at
a time.
The rider may not be less than 44 lbs, The K1 is unable to operate properly with such a
rider, especially on downhill terrains where the driver will be unable to reduce speed or
stop safety.
When you ride the K1 along with other users, please keep a certain distance between
each other to avoid a collision.
You should always keep in mind that, while on the device, your height has increased
several inches, be careful when you pass though doorways.
When turning, please maintain balance.
Do not allow distractions when riding the device, such as answering the phone or
engaging in any other activities.
Do not ride in the dark.
Avoid riding on particularly in the rain or on smooth surfaces, such as snow, ice, and
other slippery floors.
Avoid riding on particularly in the rain or on smooth surfaces, such as snow, ice, and
other slippery floors.
Do not ride on roads with obstacles (such as twigs, littler, small stones, etc.).
Avoid riding in narrow spaces or on steep slopes.
Avoid riding around flammable gas, steam, liquid, or dust that could cause fire.

19
Daily Use and Maintenance
Battery
Stop riding the K1 immediately if it displays low power.
No using the battery if it emits strange odours, overheats, or begins leaking, If the
battery does leak, please do not touch any leaking materials, as the battery contains
dangerous substances. Please do not open the battery and do not insert anything into
the battery.
Only use the provided charger for the K1. Do not charge the battery if it has over-
discharged. It should be abandoned for your safety.
Modifications
Do not attempt to disassemble, modify, repair, or replace the K1 unit or any
components of the unit. This will void any warranty and can lead to malfunctions which
may cause personal injury.
Operation
Do not lift the K1 off the ground while it is in operation and the wheels are in motion.
This can result in freely spinning wheels, which may cause personal injury to yourself or
others nearby, do not jump on or off the K1, and do not jump while using the K1 always
keep your feet firmly planted on the K1 while in operation, always check battery charge
before using, do not ride when its battery is low, as indicated by a twinkling red light or a
solid red light.

20
Maintains
Keep the device away from heat sources, direct sunlight, humidity, and prolonged
exposure to water.
Do not operate the device if it has been exposed to water, moisture, or any other liquids
to prevent against electric shock, explosion and/or injury to yourself and damage to the
device.
Do not use the device if it has been dropped or damaged in any way.
Repairs to electrical equipment should only be performed by a qualified electrician.
Improper repairs may place the user at serious risk.
Do not puncture or harm the exterior surface of the product in any way.
Keep the device free from dust, lint, etc.
Do not use this device for anything other than its intended use or purpose. Doing so
may damage the device.
This product is a toy. Please keep care of children’s safety.
Do not expose batteries, battery pack, or batteries installed to excessive heat, such as
direct sunlight, or open flame.
Wear the safety protective gear when riding, like helmet, knee pads, wrist pads, etc.