Tong Yang WPU-8900C/F Firmware update

\Y/t?
\q&
Water Dispenser
wPU-8900C/F
. Warnings for safety use
. Parts identification
. lnstallation guide
. Operation guide
. Sanitisation instructions
. Specifications
2-4 p
5-8 p
9p
1op
11p
12p
I Water Dispenser I
| - xeep tp insruaim omrua in easry aessoe rocaix. I
-.#-=:

Warnings for safety use
- Please read carefully and keep for reference in the time ol operation and
syslem trouble.
- Please note that we are nol responsible for any defect or fault of producls
casued by failure to follow the instructions or precautions.
A Warning lf warnings are ignored, serious injury risks could occur.
A precautions lf precautions are ignored injuries, property damage or perlormance
...:.r - deterioration could occur.
A This sign on the left signifies a warning or caution. When ever you see the
sign on the lvlagic Water Dispenser, please read and follow the direction
carelully.
;$warnins
$ fnis product supports the lollowing
electric ratings : 22O-240V - / 50-60H2.
- Connection to other may cause
electric damage and injury
$ Wnen installing the appliance, avoid
places or areas with excessive heat,
humidity (e.g.washrooms) direct
sunlight or areas that are
exposed to rain or snow.
- lnstallation in these
areas may cause
electric shock or *
fire. ::r.,i
A Please note that the hot {D Pt"u." keep power cord, plug and
outlet away from any water and dirt.
- Damaged supply cords to be
replaced by the manulacturer,
service agent or similar qualified
person to avoid hazard.
water temperature may
reach up to 90 Degrees
Celsius and can cause
severe burns when
dispensing hot
water lrom the
syslem.

Parts ldentification External
(Front) (Rear)
O Hot Water LED (Red) /
Safety Lock Button
@ Cold Water Tap
@ Hot Water Tap
or Ambienl
@ Upper Front Panel
@ Drip Tray
@ Top Panel
@ Main On/Oft Switch
@ Heater On/Olf Swilch
@ Cold Water Thermostat
@ Condenser
@ Hot Tank Drain Valve
@ Power LED (White)

Warnings for safety use
Awarning
.A nvoiO direct sun light or heat. /t\ lnstall the appliance on a flat and well
supported surface.
K\ Do nol move the appliance while an
operation. A fitt tnu water reservoir and hot tank
betore turning on the hot water switch.
- May cause malfunction.
- Be careful when turning on hot water
switch due to hot temperature of the
condenser panel.
&
s
s
(\
\>,
When installing this appliance always use approved parts only.
When transporting, do not tilt more than 45 degrees.
When installing this appliance position at least locm lrom the wall.
Remove the water bottle, drain all water and put the cover guard when the
appliance is not in use for an extended period of time.

Parts ldentification External
(Front)
O Hot Water LED (Red) /
Salety Lock Button
@ Cold Water Tap
@ Hot Water Tap
or Ambient
@ Upper Front Panel
@ Drip Tray
@ Lower Front Panel
@ Top Panel
@ Main On/Olf Switch
@ Heater On/Off Swltch
(Rear)
@ Cold Water Thermostat
@ Condenser Panel
@ Power LED (White)

Parts ldentification External
(Front) (Rear)
O Hot Water LED (Red) /
Safety Lock Button
@ Cold Water Tap
@ Hot Water Tap
or Ambienl
@ Upper Front Panel
@ Drip Tray
@ Top Panel
@ Main On/Oft Switch
@ Heater On/Olf Swilch
@ Cold Water Thermostat
@ Condenser
@ Hot Tank Drain Valve
@ Power LED (White)

Parts ldentification lnternal
Cold water tank
Safety Lock Button
Hot Water
Tap or Ambient
Cold Water
Tap Hot water tank
Drain valve
(Hot water)
Compressor
Adjustable Foot
Lower Front Panel
Locking Screw
t*.

Parts Identification lnternal
Hot Water Cold water tank
Condenser
Compressor
Hot water tank
Adjustable Fool
Safety Lock Button
Hot Water
Tap or Ambieni
Cold Water
Tap

Sanitisation instructions
1. Disconnect the power cord.
2. Druin cold water lrom laucet by
slightly pressing the cold tap.
3. You will lind a hot water flush valve
behind the front lower panel.
Remove the front lower panel (loose
two screw at lhe bottom of the product,
pull down and unhook the front lower
panel), unscrew the hot water drain and
direct into suitable receptacle. (When
llushing the hot water tank please
be aware that the hot water can cause
scalding)
In case of counter top model, flush valve
is at the rear side ol the system.
4. Unscrew the lelt and right screw
from the rear of the top cover, and
then remove the top cover. Next
remove the water lank cover
inside.
Flush the water pathways thoroughly
with sanitisation fluid, as appropriate
then flush with clean water and replace
the top cover and drain outlets.
5. Check for any water leaks
and ensure operation is
f unctioning correctly.
(ln the event of any
problem, contact your
distributor for technical
support.)
I Cleaning
Cold Water
lever
Screw
,%rt eaoing
Cold water tank Use soft cloth to clean with warm water (Be cautious cut one's
linger with the keen stainless tank)
Exterior Use soft cloth to clean with warm soap water (Do not use
benzene or other caustic chemical to clean)
Drip lrav Use soft cloth to clean with a neutral detergent