Toolots GSN-Z8-1 User manual

COMMERCIAL ICE MAKER
INSTRUCTION MANUAL
It is important that you read these instructions before using your commercial ice
maker and we strongly recommend that you keep them in a safe place for future
reference.

TABLE OF CONTENTS
RECEPTION AND INSPECTION ......................................................................................1
IMPORTANT SAFETY TIPS.............................................................................................. 2
APRELIMINARY UNDERSTANDING OF YOUR ICE MAKER.............................................4
INSTALLATION AND PLACEMENT OF SOLES................................................................. 5
INSTALLATION OF WATER SUPPLY AND DRAINAGE.....................................................6
CLEANING AND MAINTENANCE.................................................................................... 7
CONVENTIONAL PRECAUTIONS.................................................................................... 8
ELECTRICAL SAFETY MATTERS.......................................................................................8
CONTROL PANEL OPERATING MANUAL....................................................................... 9
OPERATION STEPS OF ICE MAKER...............................................................................10
TROUBLESHOOTING.................................................................................................... 12
TECHNICAL PARAMETERS............................................................................................14

1
Re
Thank you for selecting our company's automatic ice maker. In order to protect your
legitimate rights and interests, please pay attention to the following things when
receiving and checking the machine:
1. The outer packing of the machine is intact.
2. Machine’s model is consistent with your purchased.
3. The appearance of the machine is in good condition.
4. The attached parts are complete.
5. The internal components of the machine are in good condition.
RECEPTION AND INSPECTION

2
WARNING:This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction concerning use of
the appliance by a person responsible for their safety. Children should be supervised
to ensure that they do not play with the appliance.
WARNING: When positioning the appliance, ensure the supply cord is not trapped or
damaged.
WARNING: Do not locate multiple portable socket-outlets or portable power supplies
at the rear of the appliance.
WARNING: The illuminating LED lamp can not be replaced by the user, it must be
replaced by the manufacturer or its service agent or a similarly qualified person in
order to avoid a hazard.
WARNING: Do not store explosive substances such as aerosol cans with a flammable
propellant in this appliance.
Your personal safety and safety of others are the most important.
We have prepared many safety tips related to this machine for you.
Be sure to read and follow these tips.
This is a security warning sign
All security alerts follow the words "danger" and "warning".
If you do not comply with these safety tips, you may be seriously injured.
All safety tips describe potential hazards, tell you how to reduce the chances of injury
and what will happen if you do not follow the safety tips.
IMPORTANT SAFETY TIPS

3
If the ice maker is using or making ice, please do not touch the evaporator, which
may freeze your skin.
Before using electrical appliances, basic safety rules must be observed to reduce fire,
electric shock and damage to people or material. Please read the safety tips carefully
before using this appliance.
When the power cord is damaged, do not use and operate the machine.
use the correct power outlet and ensure that the power plug is completely
inserted into the socket.
Please do not put the power line on the carpet or heat insulation, do not cover
the power line, the power line should leave the walking channel, and do not
immerse into the water.
It is not recommended to use the power extension cord. This may result in
overheating or fire. If you must use it, use at least 1.5 square extension line.
Please cut off the power supply before cleaning or repairing.
When children are nearby, they must be supervised.
Please do not use flammable liquids to clean the ice maker. This may cause fire
or explosion.
Please do not overturn the ice maker. If there is any overturn, the machine will
be placed for 2hours before starting.
In winter, if the ice maker is moved indoors from outside, wait for a few hours before
power up, so that the temperature of the ice maker rises to the same temperature as
WARNING
evaporator
DANGER

4
that of the room.
Warning: keep ventilation free around the appliance. Do not use it in the embedded
structure.
Warning: in addition to the manufacturer's recommended method, no mechanical or
other means should be used to accelerate the defrosting process.
Warning: no damage to the refrigeration circuit.
Warning: please do not use other liquids to make ice except drinking water.
Warning:Except for the type recommended by the manufacturer, electrical
appliances should not be used in the food storage room of utensils. Explosives, such
as combustion-supporting sprays, should not be stored in appliances.This product is
suitable for milk tea shops, bars and KTV.
GZN-Z8-1
1.Box shell：No other articles are allowed to be placed on it.
2. Evaporator
3.water pipe: no deformation, breakage
4. base foot: adjustable evenness.
5. door
6. Light: bactericidal effect
7. Base foot
1
6
2
4
3
5
7
APRELIMINARY UNDERSTANDINGOF YOUR ICE MAKER

5
INSTALLATION AND PLACEMENT OF SOLES
Foot Installation And Foot Placement
1. Screw the feet of the ice maker to the baseplate.
2. Each foot must be screwed up and tightened so as
not to bend.
3. Put the ice maker in a sturdy and flat position.
4.Adjust the height of the foot to make the ice maker
level.
5. ice making machine should not be installed in the
environment without sewer and water seepage, and
it is strictly prohibited from high temperature
equipment.
6. air-cooled ice making machines (such as refrigerators, ovens, etc.) rely on air
circulation to dissipate heat. So it is necessary to keep the space above
30cm to benefit the heat dissipation.
7.please do not put anything in front of the machine，block the vent.
A
B
C
D
8. control panel:
A.regulates ice making time
B. open key
C .timing
D. cleaning

6
INSTALLATION OF WATER SUPPLY AND DRAINAGE
Warning: Only drinking water can be connected. New hose assemblies attached to
the appliances must be used. Old hose assemblies cannot be reused. Water supply
pressure should be 0.1-0.8 MPa if the pressure is greater than 0.8 MPa, need to
connect a pressure relief valve from the dry through the water of self-weight
drainage, so the drainage pipe should be adequate height or drop.
A、Connect the right-angle joint of the external intake pipe to the G3/4 head of the
rear cover plate. Make sure that the rubber seals are in the correct position and
hang the joint by hand to ensure no leakage.
B、connects the other end of the external water inlet pipe to the tap.
C、drain pipe should be connected to the outlet of the room, while ensuring that the
drain of the machine is high enough to drain the room.

7
CLEANING AND MAINTENANCE
Note: Before any cleaning or maintenance steps, please unplug the power plug and
do not use the wine tip and other highly corrosive wipers to clean the ice maker. This
may cause cracking of plastic parts.
1. Peripheral: Use a clean, soft cloth to wipe the periphery of the ice maker. At least
once a week. Use a wet cloth with a neutral cleaner to remove grease or other
impurities.
2. Ice-spoon cleaning: dip the ice-spoon into neutral detergent and water Nirvana
compound for at least 3 minutes, then rinse it with clean water and shake it dry.
3. Refrigerator cleaning: Open the ice door, remove all the ice, clean the inner wall
of the refrigerator with neutral detergent, and then rinse with clean water.
4. Pump cleaning: take off the hose, take out the pump, take off the front cover.
After rotating the inner cover counterclockwise, you can take off the inner cover.
Clean the pump fan blade with a brush. It is recommended to wash once a week.
Warning: Cyclopentane is used in insulating and insulating materials of ice maker,
and properly disposed of when discarded, such as sent to a qualified recycling
company for disposal, should not be incinerated.

8
CONVENTIONAL PRECAUTIONS
1. When transportation and mobile location, the ice machine tilt shall not exceed 45
degrees.
2. Ice machine, please use independent water source, and check regularly to
prevent water pressure is too low, fluctuations or filter clogging.
2. Do not store any sundries in the ice storage room, or freeze any food in the ice
storage room and keep the ice shovel clean.
3. Switch the ice storage bucket plastic door, should be light open and light closed,
don't beat box door, after taking the ice, please turn off the sliding door of the ice
storage bucket.
4. Ice machine should be far away from the heat source. It is strictly prohibited to
use in high temperature or low temperature environment. It is necessary to avoid
direct sunlight in order to avoid affecting the heat dissipation of the machine.
5. It is forbidden to wash the surface of ice machine directly with water, otherwise it
may lead to short circuit, leakage and other faults.
7. After the ice machine is used for a period of time, if it is stopped for a long time, it
should be electrified every two months for four to six hours.

9
CONTROL PANEL OPERATING MANUAL
ELECTRICAL SAFETY MATTERS
Warning: the machine must be grounded.
A、must have a power or socket that can provide 115V-/60Hz, and the power supply
or the socket must be reliably grounded.
B、The rated current of the B and electric box is 3.8A. If it is to be replaced, it must be
completed by professionals.
C、if the power supply or plug needs to be replaced, it must be completed by
professional after-sales service personnel.
General description : This is a fully automatic ice making machine, all programs of the
control panel have been set up in the factory. Usually, the user just need to do some
simple operation. Please place the machine in the appropriate location and connect
to power supplies.
Then the control panel will light up, the machine will run automatically, the user
need no any other operation. If you want to stop the machine, just close the ON/OFF
switch.
Note: Unplug the power supplies after finishing the day's work .

10
OPERATION STEPS OF ICE MAKER
1. Open / key:
In standby state, the power lamp flickers, press the "on/off" button, the machine
enters the ice making mode, the "ice making" lamp and the "power supply" lamp are
long on; press the "on/off" button when the machine is running, the machine stops
running and enters the standby state.
2. Timer
Press the "Timing" button, the "Timing" lamp will be on, and the "01H" will appear
on the display screen, indicating that the machine will shut down automatically after
an hour. The reservation time can be adjusted by "adjusting ten/adjusting one". After
the setting is completed, the "Timing" lamp will be on. The state is the same. Boot-up
time is reserved for shutdown time, standby time is reserved for boot-up time.
3. Turn up/Turn down:
By "turn up/turn down", the ice making time is controlled and the ice thickness is
controlled. Press "turn up/turn down" and the number will flicker on the display

11
screen.The digital display range is "-9 －15''. The smaller the number, the shorter
the ice making time, the thinner the ice. The bigger the number, the longer the ice
making time, the thicker the ice. It should be adjusted according to the size of the ice.
Ice is too thin or too thick, which is not conducive to deicing.
4.De-icing Procedure
In the de-icing procedure, ice will be heated, ice and ice grid will be the connection
will be melted, when the ice due to weight and can not be attached to the ice grid, it
will fall off, complete a de-icing process.
When the ice falls, the water plate will be turned over, and then the water
retaining plate will be reset due to the dead weight, and then the machine
starts to make ice again. When the ice bucket is too much ice, the ice block can not
be reset, and the control chip is judged to be full of ice and temporarily
shut down until the water retaining plate is reset.
5. Clean :
In boot state, press the "clean" button, the machine immediately into the deicing
state (It can be used when ice cannot be removed.); in standby state, press the
"timing" button for 3 seconds not put (timing lights are not on), the machine "clean"
light while the machine into the "clean" state.
6. Display Panel:
In working condition, the display panel shows the ambient temperature, and the
display panel digitally flashes the countdown time (minutes) for ice making.
Recommendation: use water that can be directly drunk.
7.Ice Full
When the ice is full, the baffle is pressed, and the machine shows that the ice is full.
Rebooting requires taking out the ice and tapping the baffle, or waiting for three
minutes.

12
TROUBLESHOOTING
1）Do not make ice
Problem
Inspection Project
Possible Reasons
Solution
The ice maker is
not running
Power switch
In the closed position
Press "open key".
Power cord
No connection socket
Plug in a socket
Control panel fuse
Fusing or damaging
Check and replace
Storage of refrigerators
Ice full ice blocks the evaporator
swing blade.
Remove the ice or remove the
ice from the evaporator.
If there is no such case, proximity
switch fault.
Replace proximity switch
Power supply
No electricity or voltage is too low.
Contact the power supply
department
Water supply faucet
No water or low water pressure.
Increase water pressure
Inlet valve
Filter clogged or inlet valve bad.
Clean filter screen or follow
change valve.
The compressor
doesn't work or
stop suddenly
Power supply
Low voltage
Contact the power supply
department
Air inlet
Air intake is blocked.
At least 15cm distance between
left and right sides.
condenser
Overabundance of ash
Cleaning condenser
refrigeration system
Leakage of refrigeration system
Contact after-sales service
personnel
Compressor
The connecting line is broken or
dropped.
Contact after-sales service
personnel
Water keeps on
adding water
Inlet valve
Internal leakage of inlet valve
Replacement of inlet valve
Water level sensor
Water level detection insensitive
Contact after-sales service
personnel
Water leakage
Water intake
Loosening or installation is not in
place.
Tighten or reinstall
Intake pipe or drain
pipe
Rupture leads to water leakage.
replace

13
2）Low ice production
Problem
Inspection Project
Possible Reasons
Solution
Ice making
time is too
long.
Water pressure of
water supply
The water pressure is too low, and
the water supply time is long.
Increase water pressure
water temperature
High water temperature
Water temperature reduction
ambient temperature
The ambient temperature is too high
or too low.
Suitable temperature setting
Cryogen
Refrigerant leakage
Contact after-sales service
personnel
Inlet valve
Leakage makes cooling time longer.
Replacement of inlet valve
No ice or
thin ice.
condenser
Too much ash accumulation in
condenser results in bad inlet air,
high condensation temperature and
long ice making time.
Cleaning condenser
Filter screen
The blockage of the filter leads to
poor water flow.
Cleaning or replacing filter
screen
Water pump
Poor water flow due to pump failure
Change the water pump
ambient temperature
The ambient temperature is too high.
Put it in a slightly lower
temperature.
Air inlet
Poor intake air leads to high
condensation temperature and long
ice making time.
At least 15cm space left and
rear.

14
TECHNICAL PARAMETER
Model
GSN-Z8-1
Rated Voltage
115V
Rated Frequency
60Hz
Refrigerant
R134a/0.23 lbs
Rated Current
3.8A
Vesicant
C5H10
Net Weight
50.7 lbs
Product Dimension
16.9*15.7*28(inches)
ENVIRONMENTAL PROTECTION LIST

15