top shelf concepts LD150 User manual

LID
INFUSION CHAMBER
CHAMBER HOLDER
TANK
5
FAUCET
NEED ASSISTANCE?
,
INFUSION BEVERAGE DISPENSER
Your Beverage Dispenser includes the following parts:
Item No. Description
LDL005 Lid for 3 Gal. White Infusion Beverage Dispenser
LDL006 Lid for 3 Gal. Black Infusion Beverage Dispenser
LDL009 Lid for 3 Gal. Orange Infusion Beverage Dispenser
LDL007 Lid for 5 Gal. White Infusion Beverage Dispenser
LDL008 Lid for 5 Gal. Black Infusion Beverage Dispenser
LDF005 Chamber for 3/5 Gal. White Infusion Beverage Dispenser
LDF007 Chamber for 3/5 Gal. Black Infusion Beverage Dispenser
LDF015 Chamber for 3/5 Gal. Orange Infusion Beverage Dispenser
LDF006 Chamber Holder for 3 Gal. White Infusion Beverage Dispenser
LDF008 Chamber Holder for 3 Gal. Black Infusion Beverage Dispenser
LDF014 Chamber Holder for 3 Gal. Orange Infusion Beverage Dispenser
LDF009 Chamber Holder for 5 Gal. White Infusion Beverage Dispenser
LDF010 Chamber Holder for 5 Gal. Black Infusion Beverage Dispenser
LDC001 Tank for 3 Gal. White Infusion Beverage Dispenser
LDC002 Tank for 3 Gal. Black Infusion Beverage Dispenser
LDC011 Tank for 3 Gal. Orange Infusion Beverage Dispenser
LDC003 Tank for 5 Gal. White Infusion Beverage Dispenser
LDC004 Tank for 5 Gal. Black Infusion Beverage Dispenser
LDM006 Stainless Steel Faucet
Please make sure to hand wash your beverage dispenser tank and
infusion chamber before each use! Not Dishwasher Safe!
Dimensions: (IN) 8.3” x 8.3” x 22.0” - (CM) 21.08 x 21.08 x 55.88 (3 gal)
Dimensions: (IN) 13.5” x 8.5” x 22” - (CM) 34.29 x 21.59 x 55.88 ( 5 gal)
CAPACITY:
With Infusion Chamber: 3 Gallons / 11.4 Liters
With Infusion Chamber: 5 Gallons / 18.9 Liters
RECOMENDED ACCESSORY
DRIP TRAY (LD108):
Made of stainless steel and acrylic parts, the drip tray
complements the beverage dispenser in stylistic and operational
aspects. Placed directly under the beverage dispenser faucet, the
drip tray serves as a catch basin for minor spills.
Models: LD150, LD154, LD155, LD156, LD165 US Patent: D801,744
1
2
3
4
5
1
2
3
4
5
Please contact our customer support at 1300 81 30 40 and we’ll be
happy to assist with any assembly questions, comments or concerns.
Visit our website at: www.TOPSHELFCONCEPTS.COM
Top Shelf Concepts 50 Morley st, Coorparoo. QLD. 4151

NEED ASSISTANCE?
INFUSION BEVERAGE DISPENSER
HOW TO CARE FOR YOUR ROSSETO BEVERAGE DISPENSER
Keep your beverage dispenser in good working order with these cleaning and handling tips
• Do not place any part of your beverage dispenser in the freezer or dishwasher
• Hand wash all acrylic parts with warm soapy water. Rinse and dry with soft cloth for best results
• Do not use alcohol, ammonia, or any chemical based cleaners to clean dispenser
• Do not use abrasive materials such as scrapers or metal based brushes on dispenser
• ONLY use this product for cold liquids
DO NOT USE HOT LIQUIDS WITH THIS BEVERAGE DISPENSER
DISASSEMBLY
1. Detach faucet from dispenser by unscrewing hex nut from inside tank (Figures A-1 & A-2).
2. Pull out faucet body and silicone washer from front, retrieve hex nut from inside tank.
3. Detach upper assembly from faucet body by unscrewing bonnet (Figure B). Once the upper assembly is separated
from the faucet body, pull seat cup away from handle/bonnet (Figure C). NOTE: If seat cup remains in faucet body
after it was detached from the upper assembly, remove seat cup from faucet body.
4. Clean all parts in warm soapy water.
ASSEMBLY
1. Place seat cup over stem/spring on upper assembly. Securely lock the stem into the base of the seat cup. You will
know when the seat cup is securely locked in place when it will not detach from stem easily.
2. Hand tighten upper assembly/bonnet onto faucet body. You will know that the bonnet is properly installed if no
threading is seen on the faucet body.
3. Install the faucet body onto body of dispenser. Place silicone washer over threading of faucet body MAKING
SURE SILICONE WASHER IS FLUSH WITH BACK OF FAUCET BODY (Figures A-1 & A-2).
4. With one hand, place threading of faucet body through hole in front of the dispenser. With the other hand, screw
the hex nut onto the faucet from the inside of dispenser to secure. Hand tighten only
5. Fill container at location of dispensing. Drain dispenser at the end of the day before moving. If full, 2 people are
required to move dispenser
FAUCET BODY
FAUCET BODY
SEAT CUP
SEAT
CUP
BONNET
HEX NUT
SILICONE
WA4)ER
SILICONE
WA4)ER
THREADING
UPPER
ASSEMBLY
INSIDE
WALL
OUTSIDE
WALL
FIGURE A-1 FIGURE A-2 FIGURE B FIGURE C
Please contact our customer support at 1300 81 30 40 and we’ll be
happy to assist with any assembly questions, comments or concerns.
Visit our website at: www.TOPSHELFCONCEPTS.COM
Top Shelf Concepts 50 Morley st, Coorparoo. QLD. 4151